Decentralizing India's urban development

Early in 1983 the Indian Planning Commission appointed four Task Forces on Housing and Urban Development to review existing urban policies and to recommend appropriate action starting from the Seventh Plan (1985–1989). The Task Forces covered four areas of major concern: (1) urban planning, (2) urban finance, (3) urban organizations, and (4) urban shelter. They submitted their reports by the end of 1983, and taken together these constitute the most significant review of urban policy ever undertaken in India. ¹ The Task Forces had distinguished urban experts, both officials and academics, as members, with a common Member-Secretary from the Planning Commission. The common theme in all four reports is a plea for a decentralized and equitable approach towards urban development in the country.     

Design of particle-reinforced polyurethane mould materials for soft tooling process using evolutionary multi-objective optimization algorithms

Polyurethane is used for making mould in soft tooling (ST) process for producing wax/plastic components. These wax components are later used as pattern in investment casting process. Due to low thermal conductivity of polyurethane, cooling time in ST process is long. To reduce the cooling time, thermal conductive fillers are incorporated into polyurethane to make composite mould material. However, addition of fillers affects various properties of the ST process, such as stiffness of the mould box, rendering flow-ability of melt mould material, etc. In the present work, multi-objective optimization of various conflicting objectives (namely maximization of equivalent thermal conductivity, minimization of effective modulus of elasticity, and minimization of equivalent viscosity) of composite material are conducted using evolutionary algorithms (EAs) in order to design particle-reinforced polyurethane composites by finding the optimal values of design parameters. The design parameters include volume fraction of filler content, size and shape factor of filler particle, etc. The Pareto-optimal front is targeted by solving the corresponding multi-objective problem using the NSGA-II procedure. Then, suitable multi-criterion decision-making techniques are employed to select one or a small set of the optimal solution(s) of design parameter(s) based on the higher level information of the ST process for industrial applications. Finally, the experimental study with a typical real industrial application demonstrates that the obtained optimal design parameters significantly reduce the cooling time in soft tooling process keeping other processing advantages.     

Nanoscale Studies of the Early Stages of Oxidation of a TiAl-Base Alloy

The strategy to perform nanoscale studies of the initial stages of oxidation of TiAl involved first gaining some information on the electronic structure of pure TiO₂ surfaces and then on TiAl surfaces before and after oxidation both in low- and high-oxygen potentials. Both materials were studied in atomically-cleaned states generated by repeated sputtering and heating. It was found that the oxygen vacancies created additional defect states in the band gap of stoichiometric TiO₂. The results obtained on TiO₂ were used as fingerprints to study the oxide nucleation. The results on the initial stages of oxidation of TiAl confirm the nucleation of Ti₂O₃ islands of nanometer size and monolayer height in a low-oxygen-pressure environment, whilst a TiO₂ layer developed in an atmospheric environment. The ledges on atomically-cleaned surfaces usually acted as nucleation sites.     

Studies on engineering properties of PVC–PMMA semi‐interpenetrating polymer networks

Semi1 and semi2 interpenetrating polymer networks (IPNs) of PVC and in situ formed PMMA have been synthesized using diallyl phthalate and ethylene glycol dimethacrylate as the crosslinkers of PVC and PMMA, respectively. These two types of IPNs have been compared w.r.t their physical, mechanical, and thermal properties and an endeavor has been made to find a correlation of these properties with the morphology generated in these systems. The semi1 IPNs displayed a decrease in their mechanical parameters and the physical properties as well, while in contrast, the semi2 IPNs exhibited a marginal increase in the corresponding values after an initial drop upto about 15% of crosslinked PMMA incorporation when compared to the crosslinked PVC in the case of semi1 IPN and linear PVC in the case of semi2 IPN. The various samples of semi1 and semi2 IPNs showed a two‐stage degradation typical of PVC, while confirming the increased stability with the samples having higher percentages of PMMA. The influence of crosslinking of the major matrix in semi1 IPN was almost counterbalanced by the influence of crosslinking in the dispersed PMMA phase in the case of semi2 IPN. The softening characteristics as detected by the extent of penetration of the probe, as has been detected by thermomechanical analysis, are in conformity with their mechanicals. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1725–1735, 2005     

Anodic film studies on nickel under high rate transpassive dissolution conditions

Coulometry and Auger Electron Spectroscopy (AES) were employed to study thickness and composition of anodic films formed on nickel under high rate transpassive dissolution conditions. Nickel anodes were polarized at constant current densities up to 30 A/cm² in alkaline nitrate electrolytes of different nitrate and hydroxyl ion concentration using a flow channel cell with a constant electrolyte flow velocity of 10m/sec. Results show that with increasing current density film thickness goes through a maximum. Nitrogen is detected at the apparent film metal interface in the current region where metal dissolution occurs. No correlation between anodic film thickness and dissolution efficiency is found. The data, together with previous observations, suggest that high rate transpassive dissolution takes place from film free sites.     

Mechanical and dynamic mechanical properties of jute fibers–Novolac–epoxy composite laminates

A study was done of jute composite using a polymer matrix of epoxidized Novolac resin (ENR), diglycidyl ether of bisphenol A (DGEBA)–based epoxy, and their blends with different weight percentages of the resins. It was found that on blending ENR with DGEBA, the storage modulii at room temperature are enhanced by about 100% or more in the case of 30 and 40% ENR‐containing matrices, whereas the enhancement in the case of 20 and 12% ENR‐containing matrices is only 50% that of the pure matrix. It was also observed that the tan δ peak heights of the composites containing 30 and 40% ENR are closer to that of 20% ENR‐containing composite. The probable explanation drawn on the basis of experimental findings of DMA and mechanical analysis is that by blending ENR with DGEBA epoxy it is possible to manufacture jute composites with increased stiffness without sacrificing their ductility. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2800–2807, 2002     

Increasing productivity and protein content using early-maturing rices and efficient nitrogen management

Germplasm with shorter duration than that of the currently grown varieties is being generated to maximize productivity of irrigated rice. However, short-duration varieties often produce yields lower than the medium- and long-duration varieties. Experiments were conducted during the 1980–82 dry and wet seasons to increase productivity through the use of very early-maturing rices and the improved management of nitrogen (N) fertilizers.Results over three years showed that IR58 and IR9729-67-3 (growth duration 100 ± 5 days) yield as well as or higher than IR36 although earlier maturing. They generally had a higher productivity (kg ha^–1 day^–1) than IR36 (110 ± 5 days).Three years' data suggest that the improved timing of broadcast applications of urea in split doses increased grain yield comparable with the basal incorporation of slow-release sulfur-coated urea (SCU) or deep point-placement of urea supergranules (USG).Results on elite breeding lines showed that the early-maturing IR9729-67-3 produced higher protein yield ha^–1 than longer duration varieties such as IR8 and IR42 in the dry season. Furthermore, contrary to earlier results, single basal incorporation of slow-release SCU increased the protein yield of rice by 53 kg ha^–1 and deep point-placement of USG by 43 kg ha^–1 over split application of prilled urea.