Application of single and mixtures of red sandalwood and other natural dyes for dyeing of jute fabric: studies on colour parameters/colour fastness and compatibility

Single and binary mixtures of aqueous extracts of red sandalwood (RSW) with aqueous extract of other natural dyes like manjistha (MJ), jackfruit wood (JFW), marigold (MG), sappan wood (SW) and babool (BL) in different proportions are applied on bleached jute fabric for its dyeing after double pre-mordanted with myrobolan and aluminium sulphate applied in sequence under optimised conditions of mordanting with effects of use of different proportions of binary mixture of selective natural dyes on colour strength and other colour. Parameters and colour fastness properties have been investigated. Compatibility of selective binary mixture of dyes was also judged by a relatively newer colour index parameter established earlier from this laboratory. Binary of mixture of RSW and MJ is found to be most compatible with rating 4 (in 0–5 scale), and mixture of RSW:MG and RSW:JFW is found to have average compatibility having rating 3. Dyed fabric samples have also been further treated with cationic dye-fixing agents namely N-cetyl-N-trimethylammonium bromide (CTAB), cetrimide and Sandofix-HCF to improve wash fastness. Treatment with 2% CTAB or Sandofix-HCF improves the wash fastness to nearly 1 unit. Treatment with 1% benztriazole improves the light fastness of natural dyed jute textiles nearly half to one unit. The possible chemistry and mechanisms for such improvement in wash fastness by CTAB and improvement of light fastness by benztriazole for jute have also been discussed to explain the observed effects.     

Wear Behavior of Cooling Slope Rheocast A356 Al Alloy

In the present study, the dry sliding wear behavior of rheocast A356 Al alloys, cast using a cooling slope, as well as gravity cast A356 Al alloy have been investigated at a low sliding speed of 1 ms^?1, against a hardened EN 31 disk at different loads. The wear mechanism involves microcutting–abrasion and adhesion at lower load for all of the alloys studied in the present work. On the other hand, at higher load, mainly adhesive wear along with oxide formation is observed for gravity cast A356 Al alloy and rheocast A356 Al alloy, cast using a 45° slope angle. Unlike other alloys, 60° slope rheocast A356 Al alloy is found to undergo mainly abrasive wear at higher load. Accordingly, the rheocast sample, cast using a 60° cooling slope, exhibits a remarkably lower wear rate at higher load compared to gravity cast and 45° slope rheocast samples. This is attributed to the dominance of abrasive wear at higher load in the case of rheocast A356 Al alloy cast using a 60° slope. The presence of finer and more spherical primary Al grain morphology is found to resist adhesive wear in case of 60° cooling slope processed rheocast alloy and thereby delay the transition of the wear regime from normal wear to severe wear.     

Microstructure and Oxidation Characteristics of Laser and GTAW Weldments in Austenitic Stainless Steels

The present investigation reports microstructure and high-temperature oxidation behavior of GTAW and laser weldments of 316L stainless steel. The microstructure and oxidation behavior of composite laser weldment are found to be influenced by the welding speed. In GTAW weldment, weld metal shows higher oxidation rate as compared to base metal of same weldment. Furthermore, the inoculation of Ce in GTAW weld influences the microstructure and oxidation characteristics. The scale morphologies, scale adherence, and spallation have been characterized by SEM and EDAX.     

SiC–YAG sintered composites from hydroxy hydrogel powder precursors

Yttrium hydroxide and aluminium hydroxide hydrogel were derived from yttrium nitrate and aluminium nitrate through hydroxy hydrogel route in which SiC particles were kept dispersed. The gel-like mass was heat treated at 900°C in ambient atmosphere followed by heat treatment at 1400°C in Ar atmosphere. The specimens were then sintered in the temperature range of 1800–1950°C in Ar atmosphere with 30 min soaking. The phases were identified by XRD analysis. Microstructure of the sintered materials were analysed by scanning electron micrograph. With this new method of preparation of powder precursors, the process of sintering was easier and almost theoretical density was achieved with moderate hardness. The mechanism of densification was postulated to be a solid-state initiated liquid phase sintering and the overall process of which was activated by the reactive species formed from hydroxy hydrogel powder precursors.     

Theoretical Investigation of Some High‐Performance Novel Amine Azide Propellants

Monomethylhydrazine (MMH) is currently the most widely used hypergolic propellant, due to its high performance and low ignition delay. However, its toxicity is a major concern. The present work aims at developing high‐performance hypergolic fuels that are based on tertiary amine azide functionality. A number of potential amine azide candidates have been proposed, and some of their physical and chemical properties have been computed using state‐of‐the‐art molecular modeling techniques. Gas‐phase heats of formation have been calculated using the CBS‐QB3 method, and the first‐principle COSMO‐RS method has been used to compute heats of vaporization and vapor pressures. A density correlation, based on molecular‐volume calculation, has been established to predict the densities of the candidate molecules. Finally, the liquid‐phase heats of formation and densities have been used to predict the specific and density impulses of the proposed candidate molecules. The results show that many of the molecules proposed here have much higher density impulse than that of MMH, and may be considered for experimental studies.     

Design of Alkaline/Surfactant/Polymer (ASP) Slug and its use in Enhanced Oil Recovery

Abstract

Studies have been done to design an optimum composition of alkali/surfactant/polymer (ASP) slug and its application in flooding to increase the additional recovery of oil. A very low concentration of alkali and surfactant is used to achieve ultra-low interfacial tension between the trapped oil and the injection water, and polymer is used to increase the viscosity of the injection water for mobility control. Based on the experimental results of physico-chemical properties of polymer, surfactant, and alkali and their mutual interaction in solution, an ASP slug of composition SDS: 0.1 wt%, SDBS: 0.075 wt%, polyacrylamide: 2,000 ppm, and NaOH: 0.7 wt% has been recommended for flooding. Two sets of core-flooding experiments have been conducted using the designed ASP slug in a tri-axial core holder to measure the additional recovery of oil. The average additional oil recovery over conventional water flooding was found to be more than 20% of the original oil in place (OOIP).     

Development of a Highly Selective,Sensitive, and Fast Response Upconversion Luminescent Platform for Hydrogen Sulfide Detection

Hydrogen sulfide (H₂S) has been recognized as one of most important gaseous signaling molecules mediated by a variety of physiological and pathological processes. Yet, its functions remain largely elusive due to the lack of potent monitoring methods. Hereby this issue is addressed with a powerful new platform—dye‐assembled upconversion nanoparticles (UCNPs). A series of chromophores with different absorption bands and fast responses towards H₂S is combined with UCNPs and results in a library of H₂S sensors with responsive emission signals ranging from the visible to the near‐infrared (NIR) region. These nanoprobes demonstrate highly selective and rapid responses to H₂S in vitro and in cells. Furthermore, H₂S levels in blood can be detected using the developed nanoprobes. Hence the reported H₂S sensing platform can serve as a powerful diagnostic tool to research H₂S functions and to investigate H₂S‐related diseases.     

Neutrophil N1 and N2 Subsets and Their Possible Association with Periodontitis: A Scoping Review

Periodontitis is a chronic non-communicable disease caused by dysbiotic changes that affect the subgingival microbiota. During periodontitis, neutrophils play a central role in the initial recognition of bacteria, and their number increases with the appearance of the first signs of periodontal inflammation. Recent evidence has led to the proposition that neutrophils can also functionally polarize, determining selective activity patterns related to different diseases. Two well-defined neutrophil phenotypes have been described, the pro-inflammatory N1 subset and the suppressor N2 subset. To date, it has not been established whether these different neutrophil subtypes play a role in the pathogenesis of periodontitis. Thus, this scoping review aimed to determine whether there was evidence to suggest that the neutrophils present in periodontal tissues can be associated with certain phenotypes. The research question, population, concept, and context sought to identify original articles, in humans, that detected the presence of neutrophils in the periodontal tissues of people affected by periodontitis. Based on the search strategy, we found 3658 studies. After removing the papers with abstracts not related to the outcome measures and eligibility criteria, 16 articles were included for qualitative analysis. Several studies identified the presence of different neutrophil subsets, specifically, the naive, pro- and para-inflammatory, hyper-reactive and hyper-active, and high- and low-responder phenotypes. The existing evidence demonstrates the presence of pro-inflammatory, hyper-reactive and high-responder neutrophils in periodontal tissues affected with periodontitis. There is no evidence demonstrating the presence of the N1 or N2 phenotypes in periodontal tissues during periodontitis. However, the existence of pro-inflammatory phenotypes, which increase NETosis and degranulation, and increase the production of pro-inflammatory cytokines, could be suggestive of the N1 phenotypes.     

Pharmacological and Therapeutic Applications of Esculetin

Esculetin is a coumarin compound, which belongs to the class of benzopyrone enriched in various plants such as Sonchus grandifolius, Aesculus turbinata, etc. Free radicals lead to the development of oxidative stress causing inflammation, arthritis, cancer, diabetes, fatty liver disease, etc. These further reduce the efficacy of anticancer drugs, activate inflammatory signaling pathways, degrade joints and cartilage, and disrupt the glycemic index and normal function of liver enzymes. For instance, the current treatment modalities used in arthritis such as non-steroidal anti-inflammatory drugs, disease-modifying anti-rheumatoid drugs, and lipoxygenase inhibitors present limited efficacy and adverse effects. Thus, there is a constant need to find newer and safer alternatives. Esculetin has an immense antioxidative potential thereby alleviating arthritis, diabetes, malignancies, and hepatic disorders. Structurally, esculetin contains two hydroxyl groups, which enhance its ability to function as an antioxidant by inhibiting oxidative stress in pathological conditions. Leukotriene B4 synthesis, NF-κB and MPAK pathway activation, and inflammatory cytokine production are the main causes of bone and joint deterioration in arthritis, whereas esculetin treatment reverses these factors and relieves the disease condition. In contrast, lipid peroxidation caused by upregulation of TGF-β-mediated expression and dysfunction of antioxidant enzymes is inhibited by esculetin therapy, thus reducing liver fibrosis by acting on the PI3K/FoxO1 pathway. Therefore, targeting NF-κB, pro-inflammatory cytokines, TGF-β and oxidative stress may be a therapeutic strategy to alleviate arthritis and liver fibrosis.