Morphology and characterization of conductive films based on polyaniline‐coated polystyrene latexes

The polyaniline (PANI)‐coated polystyrene (PS) latexes were synthesized, and the electrically conductive films were prepared thereafter. The weight ratio of PANI was 5%. Thermal analysis of the latices was performed using DSC and TGA. In this study, the electrically conductive films were prepared above the PS glass transition temperature (T_g). During the film formation, the effects of the annealing temperature and atmosphere (air or N₂) on the film resistance were investigated. In addition, the film morphology was observed utilizing scanning electron microscopy. The film resistance decreased in the initial heating stage due to the increasing temperature and the compaction of film. Then the film resistance increased with further annealing due to the aging of PANI. Typically, the film resistance was about 6000 Ω/sq, and the conductivity was 0.3 S/cm. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5406–5413, 2006     

多媒体教学服务系统的设计

本文从实际使用出发,提出了多媒体教学系统的设计思路,主要介绍了多媒体教学系统的系统结构、主要系统功能等。     

Electrocatalyst materials for fuel cells based on the polyoxometalates—K7 or H7[(P2W17O61)Fe(H2O)] and Na12 or H12[(P2W15O56)2Fe4(H2O)2]

Free acids of the iron substituted heteropoly acids (HPA), H₇[(P₂W₁₇O₆₁)Fe^III(H₂O)] (HFe1) and H₁₈[(P₂W₁₅O₅₆)₂Fe^III₂(H₂O)₂] (HFe2) were prepared from the salts K₇[(P₂W₁₇O₆₁)Fe^III(H₂O)] (KFe1) and Na₁₂[(P₂W₁₅O₅₆)₂Fe^III₄(H₂O)₂] (NaFe4), respectively. The iron-substituted HPA were adsorbed on to XC-72 carbon based GDLs to form HPA doped GDEs after water washing with HPA loadings of ca. 1 μmol. The HPA was detected throughout the GDL by EDX. Solution electrochemistry of the free acids are reported for the first time in sulfate buffer, pH 1-3. The hydrogen oxidation reaction was catalyzed by KFe1 at 0.33 V, with an exchange current density of 38 mA/cm². Moderate activity for the oxygen reduction reaction was observed for the iron substituted HPA, which was dramatically improved by selectively removing oxygen atoms from the HPA by cycling the fuel cell cathode under N₂ followed by reoxidation to give a restructured oxide catalyst. The nanostructured oxide achieved an OCV of 0.7 V with a Tafel slope of 115 mV/decade. Cycling the same catalysts in oxygen resulted in an improved catalyst/ionomer/carbon configuration with a slightly higher Tafel slope, 128 mV/decade but a respectable current density of 100 mA/cm² at 0.2 V.     

基于曝光适度评价的多曝光图像融合方法

针对数字相机在拍摄宽亮度范围场景时动态范围不足的问题,提出一种高效的多曝光图像融合方法.该方法通过场景的多次采样曝光,分析不同像素的亮暗变化,利用高斯数学模型计算评价数值.将结合图像亮度信息的曝光适度评价方法应用于图像分块区域,并计算每个像素的权重值,消除图像块效应.将不同曝光度下成像的图像序列融合为一幅局部自适应曝光的高动态范围(HDR)图像,实现动态范围扩展.与另外3种方法进行对比分析,结果表明:该方法简便有效,细节纹理与颜色信息具有更强的表现能力,且熵值更高.     

Microstructure and mechanical properties of pulsed DC magnetron sputtered nanocomposite Cr-Cu-N thin films

The nanocomposite Cr-Cu-N thin films have been deposited at a substrate temperature of 250 °C by a bipolar asymmetric pulsed DC reactive magnetron sputtering process. Different Cu contents ranging from 0.4 to 14.9 at.% were achieved. The structures of Cr-Cu-N thin films were analyzed by XRD. The surface and cross sectional morphologies of thin films were examined by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The nanoindentation and scratch tests were adopted to evaluate the mechanical and tribological properties of Cr-Cu-N coatings. The influences of Cu content on the structure, mechanical and tribological properties of Cr-Cu-N coatings were explored. It is observed that the columnar structure no longer exists when the Cu content exceeds 10.9 at.%. The stability of CrN phase in the coating is influenced by the Cu content. The scratching coefficient of thin films decreases with increasing Cu content. Sufficient adhesion and tribological properties of Cr-Cu-N coatings are achieved. The maximum average hardness around 20 GPa and scratching coefficient around 0.1 are found in the coatings with around 2.1 to 2.6 at.% Cu in this work.     

Effects of temperature and current density on the surface hardness and tribological properties of Ti-6Al-4V alloy by molten salt carburization

Surface hardening of Ti-6Al-4V alloy was achieved by carburization in a molten salt bath containing BaCO₃ as the carbon-yielding agent with electrolysis within the temperature range 790–930°C. The hardness of the total carburizing layer (TCD) is influenced by the bath temperature, the applied current density and the carburizing period. The major hardening effect is considered to be the formation of a solid solution of carbon in -Ti. The oxide film wrapping at the outermost surface of cathodically charged specimens, identified to be mainly BaTiO₃, was formed irrespective of the bath temperature during the quenching process and has no effect on the surface hardening. The optimal carburizing parameters obtained in this study for surface hardening are carburizing at 930±10°C (bath temperature) and 0.3 A/Cm² (applied current density) for 90 min (carburizing period), while those for tribological properties improvement are carburizing at 860±5°C and 0.3 A/Cm² for 90 min.     

An investigation on the hot extrusion process of magnesium alloy sheet

This study investigates the hot extrusion of magnesium alloy sheets at various temperatures, material, speed and lubricant. A multi-speed method is applied to extrude a magnesium alloy sheet at a high extrusion ratio. The experimental results are analyzed to optimize the processing conditions, increase the tensile strength and reduce the extrusion load on the magnesium alloy thin sheet. Nowadays, most magnesium alloy products are manufactured by industrial die casting. Hot extrusion is seldom used to finish magnesium products because the extrusion speed, temperature and extrusion load significantly effect the properties of the product. In this study, the Taguchi experimental method with the orthogonal array is applied. ANOVA is used to investigate how parameters affect the extrusion process. All possible mechanical properties of the product are analyzed to obtain the optimal process parameters. In addition, magnesium alloys with different compositions are experimentally tested to determine the mechanical properties of the extruded product and obtain the relationship between the process parameters and the properties of the material.     

An elastic net-based hybrid hypothesis method for compressed video sensing

Multimedia Tools and Applications - Compressed Sensing, an emerging framework for signal processing, can be used in image and video application, especially when available resources at the...     

A study of optimal viewing distance in a parallax barrier 3D display

The optimal viewing distance was proposed as a parameter for designing a parallax barrier 3D display. It can be designed based on simple geometric method and by considering the pitches of image display pixels and parallax barrier, or even including the aperture ratios of the image display pixels and parallax barrier. It can be analyzed by using ray tracing method. By considering the optical refraction index of the cover glass, the angular behavior of the system becomes more realistic; however, the geometric method is difficult to be used. We propose a revised method for estimating the view distance and angular behavior. In this paper, we have demonstrated a designated eye position (DEP) for each view and shown that multiple DEPs make a circular curve around the center of the display. We prove the new concept by comparing the optical ray tracing calculations and optical measurement.