Preparation and characterization of poly(vinyl chloride)–continuous carbon fiber composites

In this article, we report on the preparation and characterization of novel poly(vinyl chloride) (PVC)–carbon fiber (CF) composites. We achieved the reinforcement of PVC matrices with different plasticizer contents using unidirectional continuous CFs by applying a warm press and a cylinder press for the preparation of the PVC–CF composites. We achieved considerable reinforcement of PVC even at a relatively low CF content; for example, the maximum stress (σ_max) of the PVC–CF composite at a 3% CF content was found to be 1.5–2 times higher than that of the PVC matrix. There were great differences among the Young's modulus values of the pure PVC and PVC–CF composites matrices. The absolute Young's modulus values were in the range 1100–1300 MPa at a 3% CF content; these values were almost independent of the plasticizer content. In addition, we found a linear relationship between σ_max and the CF content and also recognized a linear variation of the Young's modulus with the CF content. The adhesion of CF to the PVC matrix was strong in each case, as concluded from the strain–stress curves and the light microscopy and scanning electron microscopy investigations. The mechanical properties of the PVC–CF composites with randomly oriented short (10 mm) fibers were also investigated. At low deformations, the stiffness of the composites improved with increasing CF content. Dynamic mechanical analysis (DMA) was used to determine the glass‐transition temperature (T_g) of the PVC–CF composites. The high increase in the Young's modulus entailed only a mild T_g increase. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Design and characterization of polypropylene matrix/glass fibers composite materials

In this article, polymer composites based on polypropylene (PP) matrix reinforced with short glass fibers type E (GF‐type E) were obtained. However, to ensure good interfacial adhesion and stress transfer across the interface, the influence of the chemical functionalization of the phases was analyzed. The better interfacial adhesion is assured by the use of maleic anhydride grafted PP and amino‐functionalized GF. The obtained composite materials were tested from the point of view of composition, morphology, and mechanical properties. It can conclude that the chemical functionalization of the two phases is beneficial from the point of view of compatibility of the phases and consequently higher mechanical properties are obtained. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42163.     

Towards a hydrodynamically enhanced design and operation of primary settling tanks – Results of a long term in situ measurement investigation program

In modern wastewater treatment the function of primary settling tanks (PSTs) has become more complex comprising the control of readily biodegradable carbon between denitrification and biogas production by an optimum performance. This requires detailed investigations in order to obtain exact knowledge of the processes within PSTs. The article shows the results of the investigation of a PST comprising in situ flow measurements and removal efficiency analysis. The measurements were carried out at different surface overflow rates, which ranged from low to even higher values than those recommended by design guidelines. This was done in order to investigate the relationship between hydrodynamic processes and removal efficiency at high hydraulic loads. Inflowing and outflowing suspended solids concentrations and loads were recorded on‐line during the measurements. The measurements provided detailed insight into the flow processes within the PST as a first step towards hydrodynamically driven design and operation control of PSTs.     

Reagentless pH-stat for microliter fluid specimens

pH-stating is a common technique for monitoring kinetics of various biochemical reactions that involve the generation of hydrogen or hydroxyl ions. In this work, we describe a reagentless electrochemical micro-pH-stat where the titrant of acid or base is produced by water electrolysis on the rotating sample system (RSS) platform. RSS originated from the authors' laboratory as a convective platform to support different analytical techniques in microliter-sized samples. As water electrolysis induces no volume change and the current that generates the reagent can be precisely measured even at low levels, very small samples in the microliter range become accessible for pH-stating: a reduction of more than an order of magnitude in specimen size relative to the most sensitive conventional methods. Nearly 100% current efficiency has been achieved with this system using a 250 microm Pt minidisc working electrode for electrolysis. The developed micro-pH-stat has been validated by the determination of the activity of erythrocyte acetylcholinesterase as a function of substrate concentration and pH. The optimal pH and activity profile obtained are in good agreement with those determined with standard techniques. The micro-pH-stat has the potential for applications for enzyme assays, reagentless pH control, acidity/alkalinity, and buffer capacity measurements in very small samples of biomedical and environmental origin.     

Wavelength- and amplitude-modulated photoacoustics: comparison of simulated and measured spectra of higher harmonics

Photoacoustic (PA) spectra generated by current modulation of a distributed feedback diode laser (DFB-DL) were measured for the ammonia absorption line at 1.53 microm and calculated using absorption spectra taken from a database. The algorithm is based on a combined amplitude- and wavelength-modulation (AM-WM) scheme. The spectral characteristics of the DFB-DL were determined by comparing simulated spectra with Fourier transform infrared measurements. PA spectra were measured and simulated from the first to fourth harmonic and a variation of the modulation depth with modulation frequency was observed. It was found that combined AM-WM modulation may produce larger PA signals than separate AM or WM detection for the first harmonic.     

Novel macromolecular inhibitors of human immunodeficiency virus-1 protease

An intracellularly expressed defective human immunodeficiency virus type-1 (HIV-1) protease (PR) monomer could function as a dominant-negative inhibitor of the enzyme that requires dimerization for activity. Based on in silico studies, two mutant PRs harboring hydrophilic mutations, capable of forming favorable inter- and intra-subunit interactions, were selected: PR(RE) containing Asp25Arg and Gly49Glu mutations, and PR(RER) containing an additional Ile50Arg mutation. The mutants were expressed and tested by PR assays, nuclear magnetic resonance (NMR) and cell culture experiments. The mutant PRs showed dose-dependent inhibition of the wild-type PR in a fluorescent microtiter plate PR assay. Furthermore, both mutants were retained by hexahistidine-tagged wild-type HIV-1 PR immobilized on nickel-chelate affinity resin. For the first time, heterodimerization between wild-type and dominant-negative mutant PRs were also demonstrated by NMR spectroscopy. (1)H-(15)N Heteronuclear Single Quantum Coherence NMR spectra showed that although PR(RE) has a high tendency to aggregate, PR(RER) exists mainly as a folded monomer at 25-35 microM concentration, but in the presence of wild-type PR in a ratio of 1:1, heterodimerization occurs with both mutants. While the recombinant virus containing the PR(RE) sequence showed only very low level of expression, expression of the viral proteins of the virus with the PR(RER) sequence was comparable with that of the wild-type. In cell culture experiments, infectivity of viral particles containing PR(RER) protein was reduced by 82%, at mutant to wild-type infective DNA ratio of 2:1.     

Exploratory study of introducing HPC to non-ICT researchers: institutional strategy is possibly needed for widespread adaption

The Journal of Supercomputing - Machine learning algorithms are becoming more and more useful in many fields of science, including many areas where computational methods are rarely used....     

Wireless sensor node localization

For most wireless sensor network (WSN) applications, the positions of the sensor nodes need to be known. Global positioning systems have not fitted into WSNs very well owing to their price, power consumption, accuracy and limitations in their operating environment. Hence, the last decade has brought about a large number of proposed methods for WSN node localization. They show tremendous variation in the physical phenomena they use, the signal properties they measure, the resources they consume, as well as in their accuracy, range, advantages and limitations. This paper provides a high-level, comprehensive overview of this very active research area.     

Ammonia detection by using quantum-cascade laser photoacoustic spectroscopy

A pulsed quantum-cascade distributed-feedback laser, temperature tunable from -41 degrees C to +31.6 degrees C, and a resonant differential photoacoustic detector are used to measure trace-gas concentrations to as low as 66 parts per 10(9) by volume (ppbv) ammonia at a low laser power of 2 mW. Good agreement between the experimental spectrum and the simulated HITRAN spectrum of NH3 is found in the spectral range between 1046 and 1052 cm(-1). A detection limit of 30 ppbv ammonia at a signal-to-noise ratio of 1 was obtained with the quantum-cascade laser (QCL) photoacoustic (PA) setup. Concentration changes of approximately 50 ppbv were detectable with this compact and versatile QCL-based PA detection system. The performance of the PA detector, characterized by the product of the incident laser power and the minimum detectable absorption coefficient, was 4.7 x 10-9 W cm(-1).     

External cavity diode laser based photoacoustic detection of CO2 at 1.43 microm: the effect of molecular relaxation

Photoacoustic spectroscopy, based on an external cavity diode laser operating at 1431 nm, was used for measuring CO2 concentration as a minority component in a gas mixture. By using N2 as a buffer gas, a molecular relaxation effect was observed, which influenced both the amplitude and the phase of the measured photoacoustic signal and consequently reduced the sensitivity of the PA system. This molecular relaxation effect could be suppressed by adding water vapor of a constant and relatively high (approximately 4%) concentration to the gas sample. In parallel with this, the arising spectral interference between H2O and CO2 necessitated the development of a simple yet efficient signal analysis method, which increased the sensitivity of the system by more than one order of magnitude and accordingly reduced the minimum detectable CO2 concentration down to approximately 1000 ppm.