Segregation of Isovalent Impurity Cations at the Surfaces of MgO and CaO

Enthalpies of segregation for isovalent impurities in magnesium and calcium oxide as a function of surface concentration were calculated by using an atomistic computer simulation method. We have considered Be²⁺, Mg²⁺, Ca²⁺, Ba²⁺, and Ni²⁺, segregating to both (001) and (110) faces. The results obtained can be extrapolated to predict the behavior of other impurities including Mn²⁺, Fe²⁺, and Co²⁺, We find, for example, that Fe²⁺, Mn²⁺, Ca²⁺, Sr²⁺, and Ba²⁺ will concentrate at the (001) surface of MgO, while Ni²⁺ will be depleted. The enthalpy of segregation is found to vary substantially with coverage particularly for the larger impurities. The enthalpy becomes less negative with increasing impurity concentration due to the increasing lattice strain until the surface is nearly saturated. Then additional stabilization is obtained by restructuring of the surface layer. We predict reconstructed surfaces for both the (001) and (110) faces, which contain a high concentration of a larger impurity ion. The enthalpy of segregation shows a maximum at around 50% surface coverage implying a bimodal surface distribution of segregant. The influence of segregation on surface energy suggests two unusual effects. The (001) surface energy of the impure crystal becomes negative for surface concentrations of impurity greater than 10% Ba²⁺ or 75% Sr²⁺ in MgO. This implies a thermodynamic barrier to sintering. At high coverages of Ba²⁺ in MgO the (110) surface becomes more stable than the (001) face suggesting that facetting may occur.     

Factors affecting cloud point analysis of palm oleins

Some of the factors affecting cloud point determination of palm oleins are described. These are the type of container used, method of stirring, rate of stirring and bath temperature. The repeatability and reproducibility standard deviations of the method are determined from collaborative trials. Recommendations for the test are made to reduce the large variations among laboratories.     

Stability studies on methyl and ethyl fatty acid esters of sunflowerseed oil

Fatty acid esters, high in linoleic acid, were prepared and stored for long-term engine tests. Storage tests with these esters were undertaken to obtain more information on optimal storage requirements and general stability characteristics. Samples were kept at three temperature levels (20 C, 30 C and fluctuating around 50 C) for a 90-day period and were removed at regular intervals for chemical and physical analysis. The influence of air, temperature, light, TBHQ and contact with mild steel was evaluated by comparing the free fatty acid, peroxide, anisidine, ultraviolet absorption, viscosity and induction periods. A statistical model was used to evaluate the data and to reduce the large number of data points to comparable curves. Storage of esters in contact with air, especially at a temperature above 30 C, resulted in significant increases in peroxide, ultraviolet absorption, free fatty acid, viscosity and anisidine values. Exclusion of air retarded oxidation at all temperature levels. A direct relationship between viscosity increases and oxidation parameters was evident. Exposure to light caused a small increase in the oxidation parameters of esters stored at the highest temperature level. Addition of TBHQ prevented oxidation of samples stored under moderate conditions. Under unfavorable storage conditions the anti-oxidant was no longer effective. Mild steel had very little effect on the oxidation parameters. Only the anisidine values of samples stored at the highest temperature level were slightly increased. Methyl esters performed slightly better than ethyl esters during the storage test. The following practical guidelines for storage of fatty acid ester fuels are: (i) airtight containers should be used; (ii) the storage temperature should be <30 C; (iii) mild steel (rust free) containers may be used, and (iv) TBHQ has a beneficial effect on oxidation stability.     

Use of electrochemical oxidation process as post-treatment for the effluents of a UASB reactor treating cellulose pulp mill wastewater.

The main purpose of this study was to evaluate the performance of the electrochemical oxidation process as a post-treatment for the effluents of a bench-scale UASB reactor treating simulated wastewater from an unbleached pulp plant. The oxidation process was performed using a single compartment cell with two plates as electrodes. The anode was made of Ti/Ru0.3Ti0.7O2 and the cathode of stainless steel. The following variables were evaluated: current density (75, 150 and 225 mA cm(-2)) and recirculation flow rate in the electrochemical cell (0.22, 0.45 and 0.90 L h(-1)). The increase in current density from 75 to 225 mA cm(-2) did not increased the color removal efficiency for the tested flow rates, 0.22, 0.45 and 0.90 L h(-1), however the energy consumption increased significantly. The results indicated the technical feasibility of the electrochemical treatment as post-treatment for UASB reactors treating wastewaters from pulp and paper plants.     

Three-Phase Induction Generator for Single-Phase Line

Hydroelectric generators of less than 20 kilowatts can be in remote areas served only by a single-phase line. For high efficiency and low cost, a three-phase induction generator should be used. This three-phase generator can operate with balanced voltages and currents when the ``phase-splitting' circuit uses two capacitors connetted to two different single-phase voltage sources.     

Improving the Public Health Information Network through Semantic Modeling

The US Centers for Disease Control and Prevention (CDC) created the Public Health Information Network to advance fully capable, interoperable information systems in public health organizations. PHIN prioritizes public health information systems' functional requirements, capabilities, performance measures, and operational characteristics while letting the architects of those systems choose enabling approaches, methods, and concepts to meet the requirements. PHIN also provides a certification process for public health administrators to evaluate their information infrastructure's quality. The certification process is important because affected organizations often depend on certification for continued funding.     

IBM RISC System/6000: architecture and performance

The IBM RISC System/6000, a superscalar microprocessor, is presented. The architecture of this processor has its instruction set specifically designed for a superscalar machine containing three independent units-branch, fixed-point, and floating-point. The design also emphasizes high-performance floating-point operations. The design principles are to offer maximum overlap of the three functional units, avoid dead cycles, and define instructions that can (for the most part) be completed at a rate of one per cycle. The branch cycle, fixed- and floating-point units, cache management, and performance are described. Benchmark results are given     

Intravaginal Controlled Administration of Flurogestone Acetate: (III) Development of Rate-Control Vaginal Devices

A Rate-Control vaginal device was developed which overcomes the low bioavailability and unpredictable Q - t^1/2 type release and absorption rate profiles of flurogestone acetate delivered by the currently marketed Syncro-Mate pessary.

The in vitro release and vaginal absorption profiles from the Rate-Control vaginal device were run simultaneously, a linear Q - t relationship was obtained with a significant improvement in bioavailability. A mathematical model was developed to correlate the in vitro drug release and the vaginal absorption profiles of flurogestone acetate from the vaginal devices.

The design, development and the simultaneous release and absorption profiles of flurogestone acetate from this new vaginal device were outlined and discussed.