Polycarbonate‐based composites reinforced by in situ polytetrafluoroethylene fibrillation: Preparation,thermal and rheological behavior

Fibrillar reinforced composites of polytetrafluoroethylene (PTFE) and polycarbonate (PC) were prepared by in situ fibrillation of PTFE into PC matrix using twin screw extruder. Different samples were obtained by varying the relative ratio between PC and PTFE. The rheological properties of the PC/PTFE composites were found to depend on concentration of the PTFE fibrils. The melt strength analysis in nonisothermal conditions was also studied. The increase in force and decrease in drawability with increasing the PTFE content are associated with the PTFE fibrils formed in situ during the thermomechanical process in twin screw extruder. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42401.     

Evolution of the Metaponto District,Southern Italy: From Land Reform to New Sustainable Scenarios

In this paper we have represented the economic, environmental and territorial transformation of Metaponto district (southern Italy) generated by the land reform since 1950. The coastal area, once inhospitable and unproductive, through land reform has become a point of development for the entire Basilicata Region. The intensive model of economic development applied to agriculture and tourism today represents the main critical points of high environmental impact. In particular, the great human pressure exerted by economic activities has led to an insufficient capacity of water purification systems in the area and such criticism is amplified in the summer mainly for seaside tourism. In this study we have measured the environmental load exerted on the territory and we have estimated the human pressure on the district in the year 2030 and made proposals for amendments to current patterns of development in the agricultural and tourist sectors.     

Engineering model for intumescent coating behavior in a pilot‐scale gas‐fired furnace

In the event of a fire, intumescent fire protective coatings expand and form a thermally insulating char that protects the underlying substrate from heat and subsequent structural failure. The intumescence includes several rate phenomena, which have been investigated and quantified in the literature for several decades. However, various challenges still exist. The most important one concerns mathematical model validation under realistic exposure conditions and/or time scales. Another is the simplification of advanced models to overcome the often‐seen lack of a complete set of input and adjustable model parameters for a given coating, thereby providing models for industrial applications. In this work, these two challenges are addressed. Three experimental series, with an intumescent coating inside a 0.65 m³ gas‐fired furnace, heating up according to so‐called cellulosic fire conditions, were conducted and a very good repeatability was evident. The experiments were run for almost 3 h, reaching a final gas temperature of about 1100°C. Measurements include transient temperature developments inside the expanding char, at the steel substrate, and in the mineral wool insulation placed behind the substrate. A mathematical model, describing the intumescent coating behavior and temperatures in the furnace using a single overall reaction was developed and validated against experimental data. By including a decomposition front movement through the char, a good qualitative agreement was obtained. After further validation against experiments with other coating formulations, it has potential to become a practical engineering tool. © 2016 American Institute of Chemical Engineers AIChE J, 62: 3947–3962, 2016     

Metformin Reduces Lipogenesis Markers in Obese Mice Fed a Low-Carbohydrate and High-Fat Diet

Lipogenesis is the process by which fatty acids are synthesized. In metabolic syndrome, an insulin resistant state along with high plasma levels of free fatty acids (FFA) and hyperglycemia may contribute to the lipogenic process. The aim of the present study was to investigate the effects of oral administration of metformin on the expression of lipogenic genes and glycemic profile in mice fed with low‐carbohydrate high‐fat diet by evaluating their metabolic profile. SWISS male mice were divided into 4 groups (N = 7) that were fed with standard (ST), standard plus metformin (ST + MET), low‐carbohydrate high‐fat diet (LCHFD) and low‐carbohydrate high‐fat diet plus metformin (LCHFD + MET) (100 mg kg^?1 diet) diets respectively. Food intake, body weight and blood parameters, such as glucose tolerance, insulin sensitivity, glucose, HDL‐c, total cholesterol, triglycerides, ASL and ALT levels were assessed. Histological analyses were performed on hematoxylin and eosin‐stained epididymal adipose tissue histological specimens. The expression levels of peroxisome proliferator‐activated receptor (PPARγ), sterol regulatory element‐binding protein 1 (SREBP1), fatty acid synthase (FAS) and acetyl‐CoA carboxylase (ACC), were assessed by RT‐PCR. This study showed that metformin decreased adipocyte area, body weight and food consumption in obese animals when compared to the standard group. Furthermore, the expression of lipogenic markers in adipose tissue were diminished in obese animals treated with metformin. This data showed that oral administration of metformin improved glucose and lipid metabolic parameters in white adipose tissue by reducing the expression of lipogenesis markers, suggesting an important clinical application of MET in treating obesity‐related diseases in metabolic syndrome.     

Tribological Behavior of Aluminum Alloy AlSi10Mg-TiB<Subscript>2</Subscript> Composites Produced by Direct Metal Laser Sintering (DMLS)

Direct metal laser sintering (DMLS) is an additive manufacturing technique for the production of parts with complex geometry and it is especially appropriate for structural applications in aircraft and automotive industries. Aluminum-based metal matrix composites (MMCs) are promising materials for these applications because they are lightweight, ductile, and have a good strength-to-weight ratio This paper presents an investigation of microstructure, hardness, and tribological properties of AlSi10Mg alloy and AlSi10Mg alloy/TiB₂ composites prepared by DMLS. MMCs were realized with two different compositions: 10% wt. of microsize TiB₂, 1% wt. of nanosize TiB₂. Wear tests were performed using a pin-on-disk apparatus on the prepared samples. Performances of AlSi10Mg samples manufactured by DMLS were also compared with the results obtained on AlSi10Mg alloy samples made by casting. It was found that the composites displayed a lower coefficient of friction (COF), but in the case of microsize TiB₂ reinforcement the wear rate was higher than with nanosize reinforcements and aluminum alloy without reinforcement. AlSi10Mg obtained by DMLS showed a higher COF than AlSi10Mg obtained by casting, but the wear rate was higher in the latter case.     

Isothermal crystallization kinetics of poly(lactic acid)/synthetic mica nanocomposites

The isothermal crystallization kinetics of PLA/fluoromica nanocomposites was studied. Three types of synthetic mica at three concentrations (2.5, 5.0, and 7.5 wt % mica) were used and the effect of these micas on the crystallization and thermal properties of PLA was investigated by differential scanning calorimetry (DSC). The Avrami and Hoffman‐Weeks equations were used to describe the isothermal crystallization kinetics and melting behavior. Addition of these micas to the PLA matrix increased the crystallization rate, and this effect depended on the mica type and concentration. While the nonmodified Somasif ME‐100 exerted the smallest effect, the effect observed for the organically modified Somasif MPE was the most pronounced. The lower half‐time of crystallization t_1/2 was around 3 min for the PLA/Somasif MPE nanocomposites containing 7.5 wt % of filler at 90°C, which is about 16 min below that found for neat PLA. The equilibrium melting temperature ( ) of PLA were estimated for these systems, showing an increase in the composites and an increase with increasing loading, except for PLA/Somasif MPE, in which the increase of the mica content decreased about 5°C. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40322.     

Mathematical modeling of the partial hydrogenation of vegetable oil in a monolithic stirrer reactor

Experimental and theoretical studies on the partial hydrogenation of vegetable oil in a monolithic stirrer reactor are reported. A complete mathematical model of the reactor was developed, including hydrogenation and isomerization kinetics, catalyst deactivation, external gas–liquid and liquid–solid as well as internal mass transfer. The experimental studies were carried out in a Pd/Al₂O₃/Al monolithic stirrer reactor, at a wide range of temperatures (353–373 K), pressures (414–552 kPa), and catalyst loadings (0.00084–0.00527 kg_Pd,exp m^?3). Based on this model, simulated data can be used to evaluate the catalyst (Pd/Al₂O₃/Al) and the hydrogenation process in consecutive catalytic tests under different operating conditions. © 2014 American Institute of Chemical Engineers AIChE J, 60: 3524–3533, 2014     

Experimental Design Applied for Cost and Efficiency of Antioxidants in Biodiesel

Oxidation stability is a parameter of great importance for biodiesel quality control to both producers and subsequent consumers. To maintain the quality of biodiesel, currently the most effective and economical method is the addition of antioxidants that prevent or retard the biofuel oxidation reaction. In this study, efficiency and cost of synthetic antioxidants added to B100 biodiesel from soybean oil and pork fat were evaluated, using butylhydroxyanisole (BHA), butylhydroxytoluene (BHT) and tert-butylhydroquinone (TBHQ), in pure form or in mixtures, according to a simplex-centroid mixture experimental design. Results demonstrate an increased induction period (IP) in all trials when compared to the control sample, and TBHQ was the only antioxidant alone that met all the specification standards, while BHT and BHA alone met only the American standard specifications. The antioxidant mixture that presented the highest synergistic effect was that of TBHQ and BHA. Multi-response optimization indicated an optimum formulation containing 75 % TBHQ and 25 % BHA with an IP of 7.27 h at 110 °C and the antioxidant mixture cost of 31.31 USD, to be added for a ton of biodiesel. This simplex-centroid mixture experimental design shows an ability to be applied in the biodiesel, oils and fats industry to evaluate the oxidation stability and the occurrence of synergism between different mixtures of synthetic or natural antioxidants and their costs.     

Vitamin E acetate addition to poly(d,l)lactic acid modifies its mechanical behavior without affecting biocompatibility

Mechanical properties of poly(d,l )lactic acid films enriched with Vitamin E and Vitamin E Acetate (5–40% w/w) were investigated. The addition of both formulations resulted in increased polymer Young's modulus and tensile strength. Human foreskin fibroblasts and murine pre‐osteoblasts were used to assess the biocompatibility of polymers. Pre‐osteoblasts adhesion and proliferation were strongly decreased by Vitamin E, whereas Vitamin E Acetate did not alter cell proliferation. Collagen deposition was lower onto Vitamin E blended polymers than onto native and Vitamin E Acetate blended ones. Fibroblasts adhesion and proliferation were increased by both Vitamin E and Vitamin E Acetate addition. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2014 , 131, 39970.