Bounds for the solution of hyperbolic problems

This article describes a newly developed and implemented method for computing guaranteed errorbounds for the solution of hyperbolic initial value problems. The basic concepts—modified fixed point theorems and approximated operators—allow an a posteriori error-estimation automatically. Therefore, no a priori knowledge of Lipschitz constants, monotonicity properties or additional error analysis is necessary.     

Biaxiale Ermüdung reibrührgeschweißter Strukturelemente

Biaxial fatigue of friction stir welded stiffened panels Within the framework of the European WelAir project, cruciform specimens made from stiffening FSW overlap joints were fatigued in the DLR biaxial test rig. To resemble the loading situation of pressurized fuselage structures, proportional loading without any phase shift, but with different load ratios λ between the loading components in both directions was applied.Natural crack initiation and subsequent crack growth were governed by the stiffness gradient caused by introducing the stringer. Cracks initiated and propagated at run‐in and run‐out locations in a direction perpendicular to the weld seam. The shortest fatigue life was observed for uniaxial loading in welding direction (λ = 0). An additional stress component perpendicular to the joint line (λ > 0) resulted in a higher number of cycles to failure. Similar to single stringer panels, increasing the load ratio also increased the number of cycles to failure for FSW clip‐stringer structural members, but additionally gives a different location of the fatal crack.     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

Verbessertes Widerstandsgesetz für Stufendiffusoren

Zusammenfassung Es wird ein allgemeines Widerstandsgesetz für Stufendiffusoren hergeleitet, bei dem die Widerstandszahl den Zusatzverlust gegenüber den Verlusten der bis zum Kontursprung reichenden fiktiven Kanal- bzw. Rohrstr?mungen in der Zu- und Abstr?mung beschreibt. Unter vereinfachenden Annahmen reduziert sich dieses Gesetz auf die bekannte Carnot-Formel. Insbesondere wird dabei der Anteil des Zusatzverlustes, der vom Unterdruck an der Stufe und von der Wandschubspannungs?nderung unmittelbar hinter der Stufe herrührt, vernachl?ssigt. Die Berücksichtigung dieses Anteils führt zu einem gegenüber der Carnot-Formel verbesserten Widerstandsgesetz. Herrn Prof. Dr.-Ing. Martin Fiebig zum 60. Geburtstag     

Production and properties of micro‐porous glas bubble zinc and aluminium composites

Micro‐porous syntactic foams were produced by means of integration of glass bubbles into aluminium and zinc matrices. Preforms of glass bubbles were pressure infiltrated with the alloys AlSi9Cu9 ans ZnAl4Cu using squeeze casting. The preforms were sintered thermically without the use of bonding agents. Using the combination of different sintering steps syntactic foams with locally different densities could be produced. The mechanical properties of the foams were tested indicating a high compression strength of the foams and a very good compression energy absorption. Furthermore, corrosion behaviour and behaviour at higher temperatures were investigated.