Novel algorithms for shared segment protection

The major challenges in designing survivable schemes are how to allocate a minimal amount of spare resources (e.g., bandwidth) using fast (e.g., polynomial-time) algorithms, and, in case a failure occurs, to be able to recover quickly from it. All existing approaches invariably make tradeoffs. We propose novel shared segment protection algorithms which make little or no compromise . We develop an elegant integer linear programming (ILP) model to determine an optimal set of segments to protect a given active path. Although the ILP approach is useful for a medium-size network, it is too time consuming for large networks. Accordingly, we also design a fast heuristic algorithm based on dynamic programming to obtain a near-optimal set of segments. Although the heuristic algorithm has a polynomial time complexity, it can achieve a bandwidth efficiency as high as some best-performing shared path protection schemes and, at the same time, much faster recovery than these shared path protection schemes. The proposed scheme is also applicable to a wide range of networking technologies, including Internet Protocol and wavelength-division multiplexing networks under the generalized multiprotocol label switched framework.     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

部分种子成分的特征X射线在等效生物材料中衰减的测定

用Ｓｉ（Ｌｉ）探测器实现了Ｎａ、Ｍｇ、Ｓ、Ｃｌ的特征Ｘ射线在有机膜中的相对衰减以及与Ｏ、Ｋ元素的特征Ｘ射线能量相当的Ｘ射线或轫致辐射在有机膜中的相对衰减，分别得出了它们减的数学描述，并把实验得到不同能量的Ｘ射线在有机膜中的质量吸收系数与Ｂｅｒｋｅｌｅｙ的ＯＣＧ软件计算出的结果相比，相关都小于３０％。     

Synthesis, characteristics and oxygen-sensitive properties of SrMgxTi 1 − xO3 nanocrystals

SrMg_xTi_{1 - x}O₃ nanocrystals (x = 0.1–0.6) were synthesized by the stearic acid gel method. Powder samples were characterized by X-ray diffraction and X-ray photoelectron (XP) spectroscopy. The results showed that the lattice parameter a and the O 1s XP spectrum changed not only with the Mg content x but also with the grain size d of the samples. The conductivity of a thick film specimen fabricated on an aluminium oxide wafer was investigated in a nitrogen—oxygen atmosphere.     

工业汽轮机的清洗

本文介绍了用饱和蒸汽对冷凝式汽轮机进行清洗除垢时主要参数的确定、操作要点及清洗方案，清洗后的汽轮机运行正常。     

Patient's self-interpretation of tuberculin skin tests

BACKGROUND: In the outpatient use of tuberculin skin testing (purified protein derivative [PPD]), it is at times inconvenient to have a patient revisit for interpretation. Therefore, we assessed patients' ability to self-interpret these test results. METHODS: In keeping with prior custom, patients were seen by an experienced nurse, who performed skin testing with PPD intermediate strength as well as mumps and Candida anergy control tests in some cases, and explained the procedure. The patients were asked to return 48 to 72 h later, at which time one of the researchers recorded their test interpretations before they were again evaluated by the nurse. RESULTS: Sixty-eight patients were studied, of whom 59 returned at appropriate interval. Eighteen patients had a positive PPD test reaction of 10 to 20 mm induration, which only one patient correctly identified as a positive test result. However, positive anergy control tests were correctly interpreted in 10 of 27 cases. CONCLUSION: The small number of positive PPD test result recognition by these patients may be partially attributed to their lack of education, as well as foreign birth and denial of illness. PPD results should be checked by an experienced professional.     

Verbessertes Widerstandsgesetz für Stufendiffusoren

Zusammenfassung Es wird ein allgemeines Widerstandsgesetz für Stufendiffusoren hergeleitet, bei dem die Widerstandszahl den Zusatzverlust gegenüber den Verlusten der bis zum Kontursprung reichenden fiktiven Kanal- bzw. Rohrstr?mungen in der Zu- und Abstr?mung beschreibt. Unter vereinfachenden Annahmen reduziert sich dieses Gesetz auf die bekannte Carnot-Formel. Insbesondere wird dabei der Anteil des Zusatzverlustes, der vom Unterdruck an der Stufe und von der Wandschubspannungs?nderung unmittelbar hinter der Stufe herrührt, vernachl?ssigt. Die Berücksichtigung dieses Anteils führt zu einem gegenüber der Carnot-Formel verbesserten Widerstandsgesetz. Herrn Prof. Dr.-Ing. Martin Fiebig zum 60. Geburtstag     

特征X射线能谱法测定Fe^＋注入小麦种子的深度

用１１０ｋｅＶ Ｆｅ＾＋离子束垂直注入小麦种胚后，在扫描电子显微镜上沿种子纵沟剖面，在不同深度上测量Ｆｅ元素被激发出的特征Ｘ射线强度分布，结果表明分布呈指数衰减，与晶体中的热扩散分布相类似，并对此进行了讨论。     

Production and properties of micro‐porous glas bubble zinc and aluminium composites

Micro‐porous syntactic foams were produced by means of integration of glass bubbles into aluminium and zinc matrices. Preforms of glass bubbles were pressure infiltrated with the alloys AlSi9Cu9 ans ZnAl4Cu using squeeze casting. The preforms were sintered thermically without the use of bonding agents. Using the combination of different sintering steps syntactic foams with locally different densities could be produced. The mechanical properties of the foams were tested indicating a high compression strength of the foams and a very good compression energy absorption. Furthermore, corrosion behaviour and behaviour at higher temperatures were investigated.