NUMERICAL ANALYSIS OF THE EFFECTS OF LOCAL HYDRODYNAMICS ON MASS TRANSFER IN HETEROGENEOUS POROUS MEDIA

Many engineering problems require the estimation of mass transfer coefficients in porous materials. In heterogeneous materials or in cases where mass transfer sites are not spatially uniform, empirical equations for mass transfer coefficients vary widely, and the origin of these differences is not well understood. In this article, we use a stochastic algorithm to model mass transfer from single particles in a two-dimensional heterogeneous packed bed. The computed mass transfer coefficients are used to generate a distribution of local Peclet numbers in the bed. Detailed hydrodynamics are then used to interpret variations in the local Peclet number. The results show clear relationships between pore structure, streamline patterns, and mass transfer rates.     

The static and dynamic characteristics of single and multiplephase-shifted DFB laser structures

The influence of longitudinal mode spatial hole burning (LMSHB) on the performance of distributed feedback (DFB) laser structures is examined in detail. A comprehensive model has been used to interpret the experimental results and to construct a theoretical framework that was utilized to develop more advanced device designs. An increasing side mode intensity with output power, movement of the lasing mode relative to the stopband, and curvature of the light-current characteristic at low power can all be manifestations of the influence of LMSHB on the static device performance. The dynamic behavior can also be affected, with extended wavelength chirp and amplitude patterning effects on the timescale of the effective carrier recombination time being particularly important     

Clinical and experimental studies of intraoperative autotransfusion using a new filtration device

The Haemocell S-350 device has recently been introduced for intraoperative autotransfusion. The system uses a novel membrane filter to process shed blood. In the first part of this study a 0.2-micron pore size filter was used in a randomized trial comparing the use of autotransfusion (n = 8) with bank blood controls (n = 9) during aortic reconstruction. This part of the trial was abandoned because of unexpected non-surgical bleeding. Bank blood requirements fell from a median of 3.0 (range 0.0-9.0) units to 1.5 (range 0.0-7.0) units when autotransfusion was used, but these patients had a greater perioperative blood loss (1791 (range 932-3104) versus 1140 (range 440-3840) ml). There was evidence of postoperative heparin excess with an activated partial thromboplastin time ratio of 1.3 (range 0.9-3.0) versus 1.0 (range 1.0-1.2) in controls and an activated clotting time of 206 (range 143-280) versus 137 (range 107-142) s. This was confirmed by raised plasma heparin levels and a prolonged thrombin time normalized by protamine. To improve performance a 0.6-micron pore size filter was studied in ten patients. Filtration efficiency doubled from 19 to 38 per cent. Electron micrographs demonstrated better filter clearance, but 44 per cent of the original concentration of heparin remained in the reinfusate. The S-350 device may be an attractive alternative to centrifugation for intraoperative autotransfusion but, until efficiency is improved, it should only be used for cardiovascular surgery when excess heparin can be reversed with protamine.     

Threshold voltage-minimum gate length trade-off in buried channelPMOS devices for scaled supply voltage CMOS technologies

The trade-off between threshold voltage (V_th) and the minimum gate length (L_min) is discussed for optimizing the performance of buried channel PMOS transistors for low voltage/low power high-speed digital CMOS circuits. In a low supply voltage CMOS technology it is desirable to scale V_th and L_min for improved circuit performance. However, these two parameters cannot be scaled independently due to the channel punch-through effect. Statistical process/device modeling, split lot experiments, circuit simulations, and measurements are performed to optimize the PMOS transistor current drive and CMOS circuit speed. We show that trading PMOS transistor V_th for a smaller L_min results in faster circuits for low supply voltage (3.3 to 1.8 V) n⁺-polysilicon gate CMOS technology, Circuit simulation and measurements are performed in this study. Approximate empirical expressions are given for the optimum buried channel PMOS transistor V _th for minimizing CMOS circuit speed for cases involving: (1) constant capacitive load and (2) load capacitance proportional to MOS gate capacitance. The results of the numerical exercise are applied to the centering of device parameters of a 0.5 μm 3.3 V CMOS technology that (a) matches the speed of our 0.5 μm 5 V CMOS technology, and (b) achieves good performance down to 1.8 V power supply. For this process the optimum PMOS transistor V_th (absolute value) is approximately 0.85-0.90 V     

Monolithically integrated laser/rear-facet monitor arrays withV-groove for passive optical fiber alignment

An InGaAsP/InP laser monolithically integrated with a rear facet monitor and a fiber V-groove has been demonstrated for the first time. The integrated device incorporates an etched-facet laser fabricated using an in situ, multistep, reactive ion etch process. The integrated V-groove, which is etched directly into the InP substrate, is designed to enable passive alignment of an optical fiber to the active region of the laser. Passive coupling efficiencies of 18% and 8% have been obtained using cleaved multimode and single mode fibers, respectively. Responsivities of the rear facet monitor were as high as 0.49 A/W     

Experimental evaluation of a multivariable adaptive nonlinear predictive controller

A new multivariable adaptive nonlinear predictive controller is designed using a general nonlinear input-output model and variable transformations. The controller is similar in form to typical linear predictive controllers can be tuned analogously or by specifying a single parameters for each controlled variable. In addition, the design procedure is computationally efficient. The new controller is compared to a multi-loop proportional-integral (PI) controller with one-way static decoupling and to an adaptive linear predictive controller through tests on a simulated nonlinear distillation column. The new controller performed well in an experimental application to a multicomponent distillation column.     

Role of cholesterol in regulating apolipoprotein B secretion by the liver

The review examines the evidence that the supply of cholesterol available for incorporation into nascent lipoprotein particles exerts a regulatory influence on apolipoprotein (apo) B secretion by the liver. Support for this hypothesis comes both from in vitro experiments and from recent observations in normal subjects and patients with dyslipidemia associated with familial hypercholesterolemia, obesity, noninsulin dependent diabetes mellitus, growth hormone deficiency and cholesteryl ester storage disease. The findings do not negate a role for triglyceride synthesis in determining apoB secretion in very low density lipoprotein, but the inhibitory effects on the latter process of pharmacological blockade of cholesterol synthesis or esterification suggest that it is conditional upon an adequate supply of cholesteryl ester.     

Silicon carbide-toughened zirconia ceramics

Tetragonal zirconia polycrystalline (TZP) ceramics containing SiC reinforcement in the form of fine particles (nano-scale), particles (micro-scale), whiskers and platelets were synthesized by hot-pressing. The effects of morphology and grain size of SiC reinforcement on the strength and fracture toughness at room temperature were investigated. The addition of SiC (in whatever form) caused decreases in strength and toughness at room temperature with the exception of whisker-reinforced materials. Toughness fell off with increasing temperature, but nevertheless retained about one-half of the room-temperature value for that particular SiC reinforcement. However, the whisker- and particle-reinforced materials had higher K _lc values at high temperature than fine particle- or platelet-reinforced materials, with values in excess of 7 MPa m^1/2 at 1000 °C. The microstructure was examined for SiC whisker-reinforced/TZP materials by TEM and HREM, to examine the nature of the whisker/zirconia interface.     

Performance evaluation of the Golay code pulse compression technique

The Center for NDE, Iowa State University, has developed a laboratory prototype Golay code pulse compression system and tested it on a variety of materials. The performance of the system was evaluated in terms of signal-to-noise ratio enhancement (SNRE), resolution, and computation speed. The system's error sources also were discussed. The Golay code pulse compression was simulated on a computer and demonstrated the effective noise suppression. In addition, an equivalent pulse of the Golay code (delta-like pulse) was derived theoretically using a simple ultrasonic inspection model, which demonstrated its equivalence on the output correlated signal. Overall, the pulse compression technique extended the detection range for a given peak power and considerably reduced the system'swhite noise, hence providing enhanced signal-to-noise ratios (SNRs). An average of 30 dB improvement in SNR was obtained from highly energy-absorbent materials such as rubber, plastics, corks (insulation materials), and thick composites using the Golay codes of up to 512 bits. However, the technique did not effectively reduce coherent scattering noises from the coarse grain boundaries in cast stainless steels, Inconel weld metal, and material lay-ups in thin composites. Furthermore, it was found that, depending upon the system's hardware capabilities, the overall performance could be degraded considerably.