Surface tension isotherms of a free surface and grain boundaries in the Cu-Sn system

Surface tension of pure copper and its alloys with Sn has been measured at 1000°C in a hydrogen atmosphere. Surface tension of a free surface equaled 1.81 N/m for pure copper, and 1.55, 1.38, and 1.28 N/m for the alloys with 0.05, 0.22, and 0.33 at % Sn, respectively; surface tension at grain boundaries equaled 0.5 N/m for pure copper, and 0.36, 0.3, and 0.23 N/m for the alloys, respectively. Based on these data, the concentration dependence of tin absorption at a free surface and grain boundaries has been calculated. Parameters of Sn absorption at grain boundaries and a free surface of copper have been compared with those of Sb and Bi.     

Influence of lead on the wear resistance of cast composites of the Fe-Cr-Cu-Ti-C system in sliding friction

The positive influence of lead (2.5%) on the original structure of a cast composite of the Fe-Cr-Cu-C-Ti system, its wear rate, friction coefficient, and the formation of secondary structures is established under the conditions of dry friction and friction with boundary lubrication. __________ Translated from Fizyko-Khimichna Mekhanika Materialiv, Vol. 42, No. 6, pp. 73–80, November–December, 2006.     

Invariance and polynomial design of strategies in the linear-quadratic game

A new algorithm to solve the H ^∞ control problem in the case of full information was presented. It combines the spectral and matrix methods. The polynomial Lur’e-Riccati operator was introduced. Parametrization of all solutions of the controlled plant equation by hidden variables was presented within the framework of the J.C. Willems behavioral approach. The kernel of the polynomial Lur’e-Riccati operator was decomposed into the direct sum of subspaces that are similar to the Jordan blocks. The saddle point of the linear-quadratic game which was found by V.A. Yakubovich in 1970 was shown to provide solution to the H ^∞ control problem for a considerable class of controlled plants.     

Securing safe operation of VVÉR reactor systems in nuclear power plants

The safe operation of VVéR reactors has been discussed throughout the entire design process, taking account of the normative documentation, including the international requirements (IAEA, EUR). After the first domestic normative document “Basic principles for securing the safety of nuclear power plants” was approved in 1973, work began on the reconstruction of the first-generation VVéR-440 power-generating units. The measures taken to increase safety concerned all types of reactors VVéR-440 and-1000. Information on implementing these measures is presented. __________ Translated from Atomnaya énergiya, Vol. 101, No. 2, pp. 87–93, August, 2006.     

Development and adoption of measures for increasing the safety of power-generating units of nuclear power plants with RBMK reactors in 1986–2005

The basic stages and directions of upgrading and reconstruction of the power-generating units of nuclear power plants with RBMK reactors over a period of 20 yr since the Chernobyl accident are reflected in this paper. The greatest amount of work was done in 1986–1990 on all units with RBMK-1000 and-1500 reactors which were operating at that time in the USSR. The purpose of the upgrade was to improve the neutron-physical characteristics of the reactor cores, increase the response speed of the safety and control system and decrease the positive effect of water outflow from the cooling loop of this system, increase the flow capacity of the systems performing emergency discharge of the steam-gas mixture from the reactor, and improve the basic operating documentation. The subsequent stages of the upgrading and reconstruction concerned mainly the first-generation power-generating units (Nos. 1 and 2 units of the Leningrad and Kursk nuclear power plants). These works were performed to make the power-generating units conform to the requirements of the modern normative documents on safety and allow for the possibility of these units to remain in operation after the nominal 30-yr service life has been exhausted. __________ Translated from Atomnaya énergiya, Vol. 100, No. 4, pp. 312–320, April, 2006.     

Ultrasound‐activated Knoevenagel condensation of malononitrile with carbonylic compounds catalysed by alkaline‐doped saponites

α,β‐Unsaturated nitriles have been synthesized by Knoevenagel condensation of a carbonylic compound with malononitrile, assisted by sonochemical irradiation. Two alkaline‐promoted clays (Li⁺‐ and Cs⁺‐exchanged saponites) have been employed as catalysts. The influence of the carbonylic compound (benzaldehyde or cyclohexanone) and the use of a solvent on the catalytic activity have been studied. Remarkable increase in the conversion values has been found when the reaction is activated by ultrasound, as compared with the thermal activation. In this green, solvent‐free procedure, α,β‐unsaturated nitriles have been produced in very high yields (97%) when the Cs⁺‐saponite is used as catalyst. Copyright © 2004 Society of Chemical Industry     

The impact of agricultural management practices on nutrient losses to water: data on the effects of soil drainage characteristics.

Against the background of increasing nutrient concentrations in Irish water bodies, this study set out to gain information on the potential of agricultural grassland to lose nutrients to water. Overland flow, flow from artificial subsurface drains and stream flow were gauged and sampled during heavy rainfall events. Dissolved reactive phosphorus (DRP), potassium (K), total ammonia (TA), and total oxidised nitrogen (TON) were measured in water samples. When the nutrient concentrations in water were examined in relation to the grassland management practices of the study catchments it emerged that soil P levels, the application of organic and inorganic fertilisers before heavy rainfall and the presence of grazing animals could all influence nutrient concentrations in surface and subsurface drainage water. Overall, the drainage characteristics of soil were found to have a considerable influence on the potential of land to lose nutrients to water.     

The Effect of Nucleators on the Quality of the Surface of Glass-Ceramic Denture Coatings

The effect of nucleator additives on the surface relief and the degree of crystallization of material intended for the dentine and enamel layers of artificial denture is considered. It is established that hydroxyapatite additive is optimal for producing the required relief in the prime and dentine layers.