Theoretical analysis of control properties for the brushless doubly fed reluctance machine

The brushless doubly fed induction machine (BDFIM) has been extensively researched for approximately 30 years, but a related machine [the brushless doubly fed reluctance machine (BDFRM)], has not. This was mainly due to the fact that reluctance rotor designs were not capable of generating saliency ratios large enough to make the BDFRM competitive with other machines. However, recent developments in reluctance rotors, spurred on by research into synchronous reluctance machines, has resulted in high saliency ratio rotors that are economic to build. This, together with the promise of higher efficiency and simpler control compared to the BDFIM, means that further investigation of the BDFRM is warranted. A relatively limited amount of work to date has been published on the BDFRM. This paper attempts to fill this void by presenting a theoretical analysis of some of the important control properties of the ideal BDFRM.     

Crisis phenomena upon evaporation in grid capillary and porous coatings and arterial structures of heat pipes

The article presents the results of experimental investigations of critical (limit) heat fluxes upon evaporation on porous coatings, and it substantiates the physical model of the process.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 49, No. 4, pp. 607–614, October, 1985.     

Structure and composition of guanidine acrylate, guanidine methacrylate, their homopolymers, and copolymers with diallyldimethylammonium chloride

Structures and compositions of the monomers guanidine acrylate and guanidine methacrylate, their homopolymers, and copolymers with diallyldimethylammonium chloride enriched in acrylate comonomer units were determined. It was shown that ampholytic copolymers, owing to their ionic nature, contained comonomeric guanidine acrylate or methacrylate units and diallyldimethylammonium chloride units, as well as the acrylate comonomer with the diallyl counterion and polymeric acrylate and diallyl ion pairs. It follows from IR and ¹H NMR data that guanidine methacrylate has the same structure (with two hydrogen bonds) in the solid state and in solutions. Guanidine acrylate structures in the solid state and in dimethylsulfoxide are identical and analogous to guanidine methacrylate structure in this solvent. In water, the guanidine acrylate structure has another type of hydrogen bonding (with one hydrogen bond, where the proton is shifted toward the guanidine group). These features of hydrogen bonding of guanidine acrylate and guanidine methacrylate are also retained in their homopolymers and copolymers with diallyldimethylammonium chloride. It was shown that the thermal stability of the copolymers was higher than that of their homopolymers, confirming the formation of intramolecular ion pairs of oppositely charged units of ampholytic copolymers. Moreover, the thermal stability of guanidine methacrylate-diallyldimethylammonium chloride copolymers is higher than that of guanidine acrylate-diallyldimethylammonium chloride copolymers.     

On the nonuniformity of a capillary flow

It is established that the capillary rise of a liquid has an oscillatory character, in contrast to the commonly accepted opinion that a vertical capillary is filled at a monotonically varying velocity. The value of the tangential shear stress arising in an ascending liquid is evaluated for ethyl alcohol and distilled water.     

Experimental Electronuclear Setup at the Institute of Theoretical and Experimental Physics

The purpose and current construction status, at the Institute of Theoretical and Experimental Physics, of an experimental electronuclear setup, combining a pulsed proton linear accelerator (36 MeV, 0.5 mA) and a subcritical blanket thermal-power assembly 100 kW, are discussed. The main equipment is already available or is being built in industry. The setup can be used to investigate the dynamics of the interaction of a linac–driver and a subcritical reactor and problems concerning the accelerator–driver and the target–blanket assembly. The proton beams and neutron fluxes will be used for applied purposes. In the future it will be possible to increase substantially the current and energy of the proton beam.     

Low-Power VLSI Implementation of the Inner Receiver for OFDM-Based WLAN Systems

In this paper, we propose low-power designs for the synchronizer and channel estimator units of the Inner Receiver in wireless local area network systems. The objective of the work is the optimization, with respect to power, area, and latency, of both the signal processing algorithms themselves and their implementation. Novel circuit design strategies have been employed to realize optimal hardware and power efficient architectures for the fast Fourier transform, arc tangent computation unit, numerically controlled oscillator, and the decimation filters. The use of multiple clock domains and clock gating reduces the power consumption further. These blocks have been integrated into an experimental digital baseband processor for the IEEE 802.11a standard implemented in the 0.25mum- 5-metal layer BiCMOS technology from Institute for High Performance Microelectronics.     

The hot blow forming of AZ31 Mg sheet: Formability assessment and application development

The hot blow forming of magnesium sheet offers significant opportunity for forming complex, lightweight parts for automotive applications. This paper characterizes the elevated-temperature formability of AZ31 magnesium sheet materials and the effect of processing conditions on the performance of these materials. In addition, magnesium sheet application development at General Motors Corporation is reviewed.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.