Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.     

Value of information in remanufacturing complex products

Remanufacturing facilities usually face a trade-off between limited information about remanufacturing yields and potentially long supplier lead times. To improve production performance, these firms may attempt to acquire more timely and accurate information about remanufacturing yields or alternatively, to reduce the lead times of purchased parts. We develop four decision-making models to evaluate the impact of yield information and supplier lead time on manufacturing costs. We identify the operating conditions under which these capabilities are valuable, along with their relative impact on facility performance. Each model is formulated as an infinite horizon, stochastic dynamic program (Markov decision process). Our results indicate that the yield information is generally quite valuable, while investments in supplier responsiveness provide trivial returns to products with few parts. However, as product complexity increases with large number of target parts, the value of short lead times increases.     

Dynamics of liquid-filled spacecraft

A method is presented for simulating coupled liquid-solid dynamics. An important example of a coupled liquid-solid system is a satellite carrying fuel. The dynamics of the satellite and the onboard fuel influence each other, which may lead to satellite motion that is uncontrollable. For better understanding of the complex dynamics of coupled systems, a numerical model is developed. The model consists of two parts. The first part that solves the liquid motion is only briefly discussed here. The focus in this paper is on the way in which the dynamics of the liquid and the solid body are coupled. For this, the governing equations are presented in which terms appear that represent the force and torque on the solid body due to the sloshing liquid. The governing equations are rewritten such that the discrete approximation of these equations can be integrated in a stable manner for arbitrary liquid/solid mass ratios. Results are presented demonstrating the stability of the present model. A grid-refinement study and a time-step analysis are performed. Finally, the flat-spin motion of a satellite, partially filled with liquid, that flew in 1992 as part of the Wet Satellite Model experiment is studied. Results from the simulation are compared with the actual flight data.     

Self-oscillating dimmable electronic ballast

This paper presents a simple alternative for an electronic ballast operating in self-sustained oscillating mode with dimming capability for fluorescent lamps. A simple modification in one of the gate drivers side circuit allows the lamp to dim without compromising the simplicity, reliability, and low cost which characterize the self-oscillating electronic ballast (SOEB). A qualitative analysis is presented to explain the behavior of the proposed self-oscillating electronic ballast with dimming feature. In addition, the stability and the key equations for the design are derived using the extended Nyquist criterion and describing function method. Experimental results from two 40-W electronic ballasts are presented to demonstrate the performance and to validate the analysis carried out.     

Characterization of the Residence Time Distribution in Spray Dryers

In this work it is presented a study on the residence time distribution (RTD) of particles in a co-current pilot-plant spray dryer operated with a rotary atomization system. A nuclear technique is applied to investigate the RTD responses of spray dryers. The methodology is based on the injection of a radioisotope tracer in the feed stream followed by the monitoring of its concentration at the outlet stream. The experiments were performed during the drying of aqueous suspensions of gadolinium oxide. The RTD responses obtained experimentally presented good reproducibility, indicating that the technique applied is well suited to investigating fluid-dynamics of spray dryers. In addition to the experimental investigation, a mathematical model was used to describe the RTD experimental curves.     

Failure analysis of a broken tooth

Several days after heart surgery, a patient discovered his upper right canine tooth had broken at the root. Such tooth damage, recognized post-operatively, is usually assumed to be caused by blunt mechanical force from an instrument used by the anesthesiologist during placement of a breathing tube at the start of surgery. In this case, the patient had saved the crown portion of the broken tooth, and it was possible to examine the root fracture characteristics. The curvature and direction of the crack path and natural tooth situation suggested that failure could be described through a cantilever beam model. This was confirmed when a whole extracted sample tooth was embedded and broken by a measured force in a manner consistent with the model. The resulting fracture surface matched that of the patient’s broken canine tooth. However, the high load and force direction necessary to fracture the root was inconsistent with forces applied during the anesthesia procedure. The failure analysis and further investigation indicated tooth clenching on the breathing tube during recovery was the likely cause of fracture. This paper presents an alternate explanation for intubation-related dental injury, demonstrates the practicality of fractographic analysis of biological materials, and introduces a methodology for simulating in vitro tooth settings for mechanical testing.     

Explosive chemistry: Simulating the chemistry of energetic materials at extreme conditions

In this article, we review recent atomistic computational techniques to study the electronic structure aspects and chemistry of energetic materials at high-pressure and/or high temperature. While several mechanisms have been proposed for the initial events of energetic materials at high-pressure, we explore the validity of a proposed shear-induced local metallization via molecular bond bending in the insensitive explosive TATB. We study the effect of high-stress (both uniform and uniaxial) on the electronic energy band-gap and the first chemical event of a prototypical energetic material, that of nitromethane. We also determine chemical reactions rate laws and decomposition mechanisms from a quantum-based molecular dynamics simulation of HMX, a widely used explosive material, at conditions of high density and temperature similar to that encounter under detonation. Finally, we review a new multi-scale computational tool recently developed to model the shock-induced chemistry of energetic materials at the atomistic level, and report its applicability to shocked solid nitromethane. This revised version was published online in June 2006 with corrections to the Cover Date.     

Evanescently coupled photodiodes integrating a double-stage taper for 40-Gb/s applications-compared performance with side-illuminated photodiodes

The design, fabrication, and performance of double-stage taper photodiodes (DSTPs) are reported. The objective of this work is to develop devices compatible with 40-Gb/s applications. Such devices require high efficiency, ultrawide band, high optical power handling capability, and compatibility with low-cost module fabrication. The integration of mode size converters improves both the coupling efficiency and the responsivity with a large fiber mode diameter. Responsivity of 0.6 A/W and 0.45 A/W are achieved with a 6-/spl mu/m fiber mode diameter and cleaved fiber, respectively, providing relaxed alignment tolerances (/spl plusmn/1.6 /spl mu/m and /spl plusmn/2 /spl mu/m, respectively), compatible with cost-effective packaging techniques. DSTPs also offer a wide bandwidth greater than 40 GHz and transverse-electric/transverse-magnetic polarization dependence lower than 0.2 dB. Furthermore, a DSTP saturation current as high as 11 mA results in optical power handling greater than +10 dBm and a high output voltage of 0.8 V. These capabilities allow the photodiode to drive the decision circuit without the need of a broad-band electrical amplifier. The DSTP devices presented here demonstrate higher responsivities with large fiber mode diameter and better optical power handling capabilities and are compared with classical side-illuminated photodiodes.     

LiNbO3 optical waveguides formed in a new proton source

Proton-exchanged planar waveguides have been fabricated on Z-cut and X-cut lithium niobate crystals by using a new proton source formed by a mixture of benzoic and adipic acids. Waveguide index profiles and optical characteristics have been obtained at different values of the adipic-benzoic acid concentration ratio. The samples have been structurally characterized by Raman and infrared (IR) absorption spectroscopy and double-crystal X-ray diffraction. Good quality samples have been fabricated by using 30 mol% ratio dilution, showing very low scattering levels (<0.1 dB/cm), relatively high electrooptic coefficient (r₃₃=0.88 pm/V), and low relative percentage of interstitial protons (26%). The main factor limiting the waveguide optical properties is the substitutional-interstitial proton ratio, which can be easily controlled to produce good quality waveguides. A demonstration of the repeatability of the exchange process in the acid mixture is also provided