Effect of spray nozzle design on liquid-solid contact in fluidized beds

In industrial fluid cokers the feedstock, consisting of heavy bituminous hydrocarbons, is atomized with steam and injected into a hot fluidized bed of coke. Good and uniform contact of the liquid droplets with the solid particles is required to provide heat for the cracking reactions while minimizing mass transfer effects. Experiments in a pilot plant coker have suggested that the initial particle/liquid mixing, in the spray jet, is rather poor. Experiments in a X-ray scanner showed that liquid droplets and entrained particles accumulate just below the tip of the jet plume to form agglomerates.An experimental technique was used to quantitatively determine the quality of mixing with a variety of nozzle configurations including several novel designs. By improving spray stability, redistributing liquid droplets to the solids-rich region of the jet and increasing the surface area of the gas-liquid jet-fluidized bed interface, liquid/solid contact is improved.     

Surface adsorption of comb polymers by Monte Carlo simulations

This paper reports off-lattice Monte Carlo simulations of highly-branched comb homopolymers weakly adsorbed on a flat, featureless surface showing only covolume and dispersion interactions with the adsorbate. A minimal coarse-grained model, described by hard spheres connected by harmonic springs, was employed. The interaction energy of the adsorbed combs and linear chains is first discussed as a function of the molecular mass and of the number of beads in contact with the surface. The molecular size is then investigated as a function of backbone length and branching density at a fixed arm size. The apparent swelling exponents of the adsorbed combs are larger than those of the corresponding linear chains, and much larger than that of the free molecules. This result indicates a surface-induced stiffening of the comb backbone, further studied through the persistence length l_pers. It is found that l_pers increases upon adsorption over the free-molecule value, more so the larger is the branching density. Finally, the thickness of the adsorbed layer, the surface-induced molecular anisotropy and the molecular aspect ratio are investigated as a function of branching density and molecular mass.     

NIST 0:45 reflectometer

The NIST 0:45 reflectometer measures the spectral reflectance factor at an influx angle of 0° and an efflux angle of 45° of colored, nonfluorescent specimens at room temperature, with widths ranging from 3 to 10 cm and heights from 3 to 20 cm and with an uncertainty of less than 0.5 in color difference units. Published in 2008 by John Wiley & Sons, Inc. Col Res Appl, 33, 94–99, 2008     

Uncertainty analysis for the NIST 0:45 Reflectometer

Sets of color tiles are available from the National Institute of Standards and Technology calibrated using the NIST 0:45 Reflectometer. The uncertainties associated with the measured values for the color tiles are an indispensable component of the calibration report that accompanies these tiles. A systematic, analytical approach developed previously was applied to the particular case of the reference instrument and color tile set, taking into account the operation and characteristics of the instrument and the spectral properties of the set. The primary sources of uncertainty were identified, and the resulting uncertainties in the color space values L*, a*, and b* were determined. In general, the uncertainties are lowest for those color tiles whose reflectance factors are nearly constant with wavelength. Published in 2008 by John Wiley & Sons, Inc. Col Res Appl, 33, 100–107, 2008     

Neutron Reflectometry Characterization of Interface Width between Sol-Gel Titanium Dioxide and Silicon Dioxide Thin Films

Neutron reflectometry (NR) was used to directly measure the interface width between a titanium dioxide and a silicon dioxide film deposited by sol-gel processing. In a bilayer heated to 450°C, NR measurements showed that the interface width is 0.8 nm. This width is the same as the roughness of a sol-gel silicon dioxide surface after the same heat treatment, suggesting no interdiffusion or mixing at the bilayer interface.     

Comparison of orthorhombic and alpha-two titanium aluminides as matrices for continuous SiC-reinforced composites

The attributes of an orthorhombic Ti aluminide alloy, Ti-21Al-22Nb (at. pct), and an alpha-two Ti aluminide alloy, Ti-24Al-11Nb (at. pct), for use as a matrix with continuous SiC (SCS-6) fiber reinforcement have been compared. Foil-fiber-foil processing was used to produce both unreinforced (“neat”) and unidirectional “SCS-6” reinforced panels. Microstructure of the Ti-24A1-11Nb matrix consisted of ordered Ti₃Al (α ₂) + disordered beta(β), while the Ti-21 Al-22Nb matrix contained three phases: α₂, ordered beta (β ₀), and ordered orthorhombic(O). Fiber/ matrix interface reaction zone growth kinetics at 982 °C were examined for each composite system. Although both systems exhibited similar interface reaction products(i.e., mixed Ti carbides, silicides, and Ti-Al carbides), growth kinetics in theα ₂ +β matrix composite were much more rapid than in theO +β ₀ +α ₂ matrix composite. Additionally, interfacial reaction in theα ₂ +β} composite resulted in a relatively large brittle matrix zone, depleted of beta phase, which was not present in theO +β ₀+α ₂ matrix composite. Mechanical property measurements included room and elevated temperature tensile, thermal stability, thermal fatigue, thermo-mechanical fatigue (TMF), and creep. The three-phase orthorhombic-based alloy outperformed the α₂+β alloy in all of these mechanical behavioral areas, on both an absolute and a specific(i.e., density corrected) basis.     

Microstructure and Dielectric Characteristics of (PbxBa0.5−xSr0.5)TiO3 Ceramics

Microstructural and dielectric properties of the Pb _x Ba _0.5__x —Sr_0.5TiO₃ system have been studied. It is found that this system forms a solid solution in the entire composition range (0.0≤ x ≤0.5) and is cubic for the x = 0, 0.1, and 0.2 compositions and tetragonal for other compositions. Measurements of the dielectric constant as a function of temperature reveal that this material is ferroelectric at room temperature for the x > 0.2 compositions and has a broad paraelectric-ferroelectric transition region. No shift in the dielectric maxima was noted; however, there is a slight spread in the dielectric constant with frequency for the x = 0.4 composition. A quantitative model to mathematically analyze the effect of composition fluctuations on the dielectric broadening for a ternary system is presented. Transmission electron microscopic studies reveal the presence of 90° ferroelectric domains oriented along the {01     } planes for the x = 0.3 and 0.4 compositions.     

Interrelations of social support measures: Theoretical and practical implications.

To obtain a clearer picture of what constitutes social support, we conducted three studies to compare measures of different conceptions of social support. Relations of these instruments to various personality measures were also investigated. Subdividing the construct into discrete functions did not add to the sensitivity of the indices. Measures of received support and support networks were not strongly related to most of the perceived available support measures. Interview and questionnaire approaches were similar in the information they evoked about close supportive relationships. The results suggest that measures of perceived available support, regardless of the way the instruments attempt to break down the construct, generally assess the extent to which an individual is accepted, loved, and involved in relationships in which communication is open. Psychometric characteristics of the measures were associated with differential sensitivity over the range of supportive relationships. The theoretical implications of the findings are discussed with emphasis on the common core underlying social support indices. (PsycINFO Database Record (c) 2010 APA, all rights reserved)