Synthesis, characterization and application of allyl phenol modified amberlite XAD-4 resin for preconcentration and determination of copper in water samples

A new chelating resin was prepared by coupling Amberlite XAD-4 with phenol through an azo spacer, then modified by allyl bromide and characterized (by elemental analysis and IR) and studied for preconcentration of Cu(II) using flame atomic absorption spectrometry (FAAS) for metal monitoring. The optimum pH value for sorption of the above mentioned metal ion was 4.5. The resin was subjected to chemical evaluation through batch binding and column chromatography of Cu(II). The chelating resin can be reused for 15 cycles of sorption-desorption without any significant change in sorption capacity. A recovery of 98% was obtained for the metal ion with 0.5 M HNO₃ as eluting agent. The equilibrium adsorption data of Cu(II) on modified resin were analyzed by Langmuir, Freundlich and Temkin models. Based on equilibrium adsorption data the Langmuir, Freundlich and Temkin constants were determined to be 0.061, 0.193 and 0.045 at pH 4.5 and 25 °C. The method was applied for the copper determination from industrial waste water sample.     

A method for preparation and application of micronized ferrite pigments in anticorrosive solvent-based paints

This work presents a method of preparing single-, double-, and triple-cation ferrite pigments by employing simple chemical techniques to study their corrosion protection properties. The prepared pigments were characterized using X-ray diffraction and scanning electron microscopy. All prepared ferrite pigments were evaluated using ASTM methods. Anticorrosive paint formulations were performed using different prepared pigment loadings. The physico-mechanical and corrosion properties of dry paint films were examined. The tests revealed that the prepared ferrite pigments show excellent anticorrosive behavior, and that the best among them in performance are zinc and zinc magnesium. Calcium, zinc–calcium, and zinc–magnesium–calcium ferrites show better performance in high pigment loadings, while magnesium ferrite pigments show good results only in low pigment loading.     

Investigation of Removal of Cu(II) Ions by Commercial Activated Carbon: Equilibrium and Thermodynamic Studies

Protection of Metals and Physical Chemistry of Surfaces - The present study deals with the application of activated carbon for the adsorptive removal of Cu(II) from its aqueous solutions. This...     

Hydrophobic polyethersulfone porous membranes for membrane distillation

Membrane distillation (MD) is a thermal, vapor-driven transportation process through micro porous hydrophobic membranes that is increasingly being applied to seawater and brine desalination processes. Two types of hydrophobic microporous polyethersulfone flat sheet membranes, namely, annealed polyethersulfone and a polyethersulfone/tetraethoxysilane (PES/TEOS) blend were prepared by a phase inversion process. The membranes were characterized and their performances were investigated using the vacuum membrane distillation of an aqueous NaCl solution. The performances of the prepared membranes were also compared with two commercially available hydrophobic membranes, polytetrafluorethylene and polyvinylidene fluoride. The influence of operational parameters such as feed temperature (25–65 °C), permeate vacuum pressure (200–800 mbar), feed flow rate (8–22 mL/s) and feed salt concentration (3000 to 35000 mg/L) on the MD permeation flux were investigated for the four membranes. The hydrophobic PES/TEOS membrane had the highest salt rejection (99.7%) and permeate flux (86 kg/m²·h) at 65 °C, with a feed of 7000 ppm and a pressure of 200 mbar.     

Performance characteristics of a miniaturised chemical looping steam reformer for hydrogen enrichment of fuels

A miniaturised chemical looping steam reformer (μ-CLSR) is being developed at the University of Newcastle (Australia) for onboard hydrogen enrichment of fuels in internal combustion engines. Experimental results from the first prototype highlighted an imbalance between the rates of redox reactions. A new configuration has been developed to resolve this shortcoming. The objective of this study is to examine the effectiveness of the new configuration in handling the imbalance between redox rates. Experiments were conducted on magnetite and wuestite metal oxides under methane and steam environments in the new configuration. Results indicate that if micro-reactors within the reformer are operated in parallel during the oxidation half cycle and in sequence during the reduction half cycle, the imbalance can be effectively managed. This combined with manifold switching of reacting gases at 48 s intervals enables metal oxides to achieve a 30% fractional conversion at 900 °C; resulting in a product gas stream with 96% H₂ purity.     

Effects of colloidal properties on sensible heat transfer in water-based titania nanofluids

Nanofluids have attracted considerable attention in recent years as effective working fluids in heat transfer applications. Nanofluids are essentially suspensions of nanoparticles in a base fluid and exhibit higher thermal conductivity than conventional heat transfer fluids.     

Numerical analysis of transport phenomena for designing of ejector in PEM forklift system

In the present study, Computational Fluid Dynamics (CFD) technique is used to design an ejector for anode recirculation in an automotive PEMFC system. A CFD model is firstly established and tested against well-documented and relevant solutions from the literature, and then used for different ejector geometries under different operating conditions. Results showed that a single ejector with optimized geometry cannot cover the required recirculation in the entire range of the fuel cell current. Having two ejectors for different ranges of currents is thus proposed as an alternative solution in which the system can better take the advantage of ejectors for recirculation purpose. In addition, the operating mode of one variable nozzle ejector has been investigated and compared with aforementioned cases. The results showed that the variable nozzle ejector can work in the same operational mode as in the case with two ejectors. However, in practice, the latter one needs a more complicated control system and it is more difficult to manufacture.     

Mechanical properties of composites from sawdust and recycled plastics

Mechanical properties of wood plastic composites (WPCs) manufactured from sawdust and virgin and/or recycled plastics, namely high density polyethylene (HDPE) and polypropylene (PP), were studied. Sawdust was prepared from beech industrial sawdust by screening to the desired particle size and was mixed with different virgin or recycled plastics at 50% by weight fiber loading. The mixed materials were then compression molded into panels. Flexural and tensile properties and impact strength of the manufactured WPCs were determined according to the relevant standard specifications. Although composites containing PP (virgin and recycled) exhibited higher stiffness and strength than those made from HDPE (virgin and recycled), they had lower unnotched impact strengths. Mechanical properties of specimens containing recycled plastics (HDPE and PP) were statistically similar and comparable to those of composites made from virgin plastics. This was considered as a possibility to expand the use of recycled plastics in the manufacture of WPCs. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3641–3645, 2006     

Shading and lighting operation in office buildings in Austria: A study of user control behavior

Occupants of buildings typically operate devices such as windows, shades, luminaires, radiators, and fans to bring about desirable indoor environmental conditions. These control actions can have a significant impact on buildings’ performance (energy use, indoor climate). A better understanding of control-oriented user behavior can not only facilitate more accurate predictions of buildings’ performance, but also support the effective operation of buildings’ service systems. This paper describes a study of control-oriented user behavior (as related to systems for lighting and shading) in three office buildings in Austria. The results specifically shed light on the relationships between control actions and environmental conditions inside and outside buildings.