Effects of colloidal properties on sensible heat transfer in water-based titania nanofluids

Nanofluids have attracted considerable attention in recent years as effective working fluids in heat transfer applications. Nanofluids are essentially suspensions of nanoparticles in a base fluid and exhibit higher thermal conductivity than conventional heat transfer fluids.     

Numerical analysis of transport phenomena for designing of ejector in PEM forklift system

In the present study, Computational Fluid Dynamics (CFD) technique is used to design an ejector for anode recirculation in an automotive PEMFC system. A CFD model is firstly established and tested against well-documented and relevant solutions from the literature, and then used for different ejector geometries under different operating conditions. Results showed that a single ejector with optimized geometry cannot cover the required recirculation in the entire range of the fuel cell current. Having two ejectors for different ranges of currents is thus proposed as an alternative solution in which the system can better take the advantage of ejectors for recirculation purpose. In addition, the operating mode of one variable nozzle ejector has been investigated and compared with aforementioned cases. The results showed that the variable nozzle ejector can work in the same operational mode as in the case with two ejectors. However, in practice, the latter one needs a more complicated control system and it is more difficult to manufacture.     

Basis weight uniformity analysis in nonwovens

It is widely recognized that nonwoven basis weight uniformity affects various properties of nonwovens, including appearance, physical properties, or mechanical properties. However, it is one of the nonwoven characteristics that is most difficult to characterize. This paper reports on the methodology based on the well-known quadrant method that objectively quantifies uniformity of nonwoven fabrics.     

Effect of enzymatic and mechanical treatment on combined desizing and bio-polishing of cotton fabrics

The main objective of this study was to improve the enzymatic effect by mechanical treatment on cotton fabric in combined desizing and bio-polishing. The purpose is to create a commercially and environmentally friendly process for water and energy saving. The effect of mechanical treatment and different enzyme concentration was studied. Both mechanical and enzymatic treatment effect were evaluated through measuring weight loss and light measurement of fabric surface. Fabric surface evaluation also was done via photo micrographing. Fabric hairiness was illustrated on captured photos of treated and untreated fabric. Finally, optimized data of treatment were obtained.     

Evaluation of Mass Exchange During Osmotic Dehydration of Plum Using Response Surface Methodology

Water loss (WL), solid gain (SG), weight reduction (WR) and shrinkage were quantitatively investigated during osmotic dehydration of plum using response surface methodology with the sucrose concentration (30–60g/100 g sample), temperature of sucrose solution (40–60°C) and immersion time (60–240 min). Experiments were designed according to Central Composite Rotatable Design with these three factors. For each response, second order polynomial models were developed using multiple linear regression analysis. With respect to water loss, solid gain, weight reduction and shrinkage, both linear and quadratic effects of four variables were found to be significant. In most cases, an increase of sucrose concentration, temperature and immersion time increased WL, SG, WR and shrinkage, except the increasing of immersion time for osmotic treatment has no effect on shrinkage. It was found that immersion time and temperature were the most significant factors affecting the WL during osmotic dehydration of plum followed by concentration of sucrose solution. This was also true for WR. Effect of temperature and time were more pronounced for SG than the concentration of sucrose solution.     

Optimistic Selection of Cluster Heads Based on Facility Location Problem in Cluster-Based Routing Protocols

Cluster-based routing protocols are one of the most favorable approaches for energy management in wireless sensor networks. The selection of the best cluster heads (CHs), as well as the formation of optimal clusters, is an NP-hard problem. The present study proposes an optimal solution for CHs selection to generate a network topology with optimized network performance. The problem is formulated as facility location problem and a linear programming model is used to solve the optimization problem. Results of analysis o the network simulator (NS2) indicate that applying this method in cluster-based routing protocols prolongs 16 % of the network lifetime, increases 15.5 % of data transmission and improves 5.5 % of throughput, as compared to the results of current heuristic methods such as LEACH, DEEC and EDFCM protocols.     

Mechanical properties of composites from sawdust and recycled plastics

Mechanical properties of wood plastic composites (WPCs) manufactured from sawdust and virgin and/or recycled plastics, namely high density polyethylene (HDPE) and polypropylene (PP), were studied. Sawdust was prepared from beech industrial sawdust by screening to the desired particle size and was mixed with different virgin or recycled plastics at 50% by weight fiber loading. The mixed materials were then compression molded into panels. Flexural and tensile properties and impact strength of the manufactured WPCs were determined according to the relevant standard specifications. Although composites containing PP (virgin and recycled) exhibited higher stiffness and strength than those made from HDPE (virgin and recycled), they had lower unnotched impact strengths. Mechanical properties of specimens containing recycled plastics (HDPE and PP) were statistically similar and comparable to those of composites made from virgin plastics. This was considered as a possibility to expand the use of recycled plastics in the manufacture of WPCs. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3641–3645, 2006     

Shading and lighting operation in office buildings in Austria: A study of user control behavior

Occupants of buildings typically operate devices such as windows, shades, luminaires, radiators, and fans to bring about desirable indoor environmental conditions. These control actions can have a significant impact on buildings’ performance (energy use, indoor climate). A better understanding of control-oriented user behavior can not only facilitate more accurate predictions of buildings’ performance, but also support the effective operation of buildings’ service systems. This paper describes a study of control-oriented user behavior (as related to systems for lighting and shading) in three office buildings in Austria. The results specifically shed light on the relationships between control actions and environmental conditions inside and outside buildings.