The effect of substrate on the composition of polyhydroxyalkanoates in enhanced biological phosphorus removal

This paper primarily evaluates the effect of external substrate type on the composition of polyhydroxyalkanoates in enhanced biological phosphorus removal (EBPR). Two sets of sequencing batch reactors (SBRs) are operated for this purpose, one with acetate and the other with propionate as the sole carbon source at different influent COD/phosphate ratios in the range 6.7–20 mgCOD mg^?1P. Results indicate that propionate is a more efficient substrate for EBPR, enabling total phosphate removal regardless of the change in COD/phosphate ratio. Total polyhydroxyalkanoates formation of 267–291 mgCOD L^?1 with a slight increase at higher influent phosphorus levels is observed for acetate experiments, and a slightly lower level of 250–280 mgCOD L^?1, with a similar trend for propionate experiments. The volatile fatty acid type and composition in the influent induces a significant difference in the polyhydroxyalkanoates composition of the two sets of activated sludge sustained in corresponding SBR systems. Propionate is mostly stored as 3‐hydroxy‐2‐methylvalerate and polyhydroxyvalerate, while acetate is stored as polyhydroxybutyrate. The P uptake rate in SBRs fed with propionate is considerably higher than that in the acetate reactors. Parallel batch experiments yield different results, especially for systems fed with acetate, indicating that the enzymatic system to metabolize propionate is not rapidly established, always yielding a dominant polyhydroxybutyrate fraction in the generated polyhydroxyalkanoates regardless of the level of propionate in the feed. Copyright © 2007 Society of Chemical Industry     

Ion exchange with natural zeolites: an alternative for water softening?

Possibility of using natural zeolites for water softening was investigated. Quantitative data regarding separation of calcium from water at various levels of hardness through ion exchange with the ammonium selective natural zeolite clinoptilolite is reported. Capacity of the zeolite towards calcium removal in the presence of ammonium at low concentrations and calcium at higher concentrations, and breakthrough characteristics are presented. The results have revealed that removal of calcium, and hence hardness, through ion exchange with clinoptilolite under those circumstances is a promising alternative, with surface capacities reaching 11 mg calcium/g clinoptilolite.     

Examination of Dyeing Properties of the Dyed Cotton Fabrics with Barberry (Berberis vulgaris L.)

ABSTRACT

In this study, it was aimed at investing the cotton fabrics dyed with different percentages of the roots of barberry (Berberis vulgaris L.) via gall oak (Quercus infectoria Olivier; 10% and 20%) and aluminum sulfate (Al₂(SO₄)₃; 6%) mordants. The dyeing process was performed with the roots of barberry in the range of 10–100%. A reversed phase high performance liquid chromatography with diode array detection method was utilized for the identification of dyes present in the sample extracts. Natural yellow-dyed cotton samples were studied calorimetrically and their color coordinates L*, a*, b*, C*, h, K/S, and ?E* values were given.     

Natural ink production and printability studies for smart food packaging

Versatile smart packages provide information on the freshness of the content and help protect the content from microorganisms. In this sense, in this study both natural antimicrobial properties and pH sensitive natural dyes were obtained from red beet. Inks were prepared and printed using this dye and their suitability for smart packaging was investigated. For this purpose, red beet was cut into small sizes and mixed separately in ethanol and water (1:2) at 200 rpm. The betaine dye was taken up in solvent. These solvents were removed with evaporator and precipitated with centrifugation and dried in a vacuum oven. The chemical structure of the obtained dye was illuminated by Attenuated Total Reflection-Fourier Transform Infrared Spectroscopy (ATR-FTIR). The color character was determined by UV spectroscopy. Pink colored natural ink was produced by using ink varnish with carboxymethyl cellulose polymer and solid dye. Screen printing was made with this ink and the color, gloss, and lightfastness characters of prints were examined. Antimicrobial effects of the obtained prints were measured against Staphylococcus aureus and Escherichia coli. Mordanting studies were performed with (KAl[SO₄]₂.12H₂O) and change in color character was measured. The prints produced using the red beet extract have a yellow-orange color in the basic state; in acid cases it was determined to have a pink-purple color. In addition, it has been found that the ink prints obtained from red beet have antimicrobial properties against bacteria. Results prove that produced samples have good antimicrobial, pH indicator, and printability properties. This colorant can be used in smart food packaging.     

Effect of process parameters and talc ratio on hot plate welding of polypropylene

This study analyzes the influence of different talc ratios on weld strength of polypropylene joined with hot plate welding process. It further determines the optimum welding parameter settings to achieve the optimum weld strength and observes the effect of process parameters, namely plate temperature and heating time on the joint quality. Process parameters were considered as variables and their effect, interactions and relative significance were investigated by utilizing design of experiment. Simultaneously, a mathematical predictive model of the weld strength was developed in terms of welding parameters. The model can predict effectively weld strength with a 95% confidence level.     

Optimization of the enzymatic production of isoamyl acetate with novozym 435 from candida antarctica

In this study the production of isoamyl acetate by esterification of isoamyl alcohol and acetic acid was carried out using immobilized C . antarctica lipase (Novozym 435) as a catalyst without any organic solvent. The esterification yield was optimized with response surface methodology. This method was used with four parameters to evaluate the effects of important variables on the esterification yield. The parameters are acid/alcohol mole ratio (0.2-0.8), enzyme amount (4-12%, w/w), temperature (30-50 °C), and reaction time (4-8 hr). It was found that the most effective parameter was acid/alcohol mole ratio. As acid/alcohol mole ratio increased at any given reaction time and amount of enzyme, ester concentration, C p (mmol ester/g mixture), increased up to an acid/alcohol mole ratio of 0.7 and thereafter decreased. The model indicated the optimum conditions for maximum esterification (3.45 mmol ester/g mixture) in the acid/alcohol mole ratio of 0.52 for 8.15% enzyme at 43.2 °C and after 5.27 hr, which were in good agreement with the experimental value (3.5 mmol ester/g mixture).     

Determination of hydroquinone using poly(3‐methylthiophene) synthesized electrochemically on pt electrode in methylene chloride

Poly(3‐methylthiophene) (P3MT) film was synthesized by potentiodynamic method on Pt electrode in methylene chloride solution containing 0.10M tetrabuthlammonium perchlorate supporting electrolyte and used for the determination of hydroquinone (HQ) with amperometric I–t method in solution consisting of NaHSO₄/Na₂SO₄ (SBS; pH 2.0). This modified electrode has a lower working potential and good operational stability due to reducing electrode fouling when compared with the direct oxidation of HQ at the bare Pt electrode. Limit of detection, limit of quantification, and the linear response range were found to be 1.32 × 10^?5 mM, 4.41 × 10^?5 mM, and between 4.41 × 10^?5 – 50.0 mM (R² = 0.997), at 0.50 V versus saturated calomel electrode, respectively. HQ determination in complex matrix was checked using real samples to demonstrate the applicability of modified electrode. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40859.     

Catalyst incorporation at defects during nanowire growth

Scanning and transmission electron microscopy was used to correlate the structure of planar defects with the prevalence of Au catalyst atom incorporation in Si nanowires. Site-specific high-resolution imaging along orthogonal zone axes, enabled by advances in focused ion beam cross sectioning, reveals substantial incorporation of catalyst atoms at grain boundaries in <110> oriented nanowires. In contrast, (111) stacking faults that generate new polytypes in <112> oriented nanowires do not show preferential catalyst incorporation. Tomographic reconstruction of the catalyst-nanowire interface is used to suggest criteria for the stability of planar defects that trap impurity atoms in catalyst-mediated nanowires.