Testing of the multi-application small light water reactor (MASLWR) passive safety systems

Experimental thermal hydraulic research has been conducted at Oregon State University for the purpose of assessing the performance of a new reactor design concept, the multi-application small light water reactor (MASLWR). The MASLWR is a pressurized light water reactor design with a net output of 35 MWe that uses natural circulation in both normal and transient operation. Due to its small size, portability and modularity, the MASLWR design is well suited to help fill the potential need for grid appropriate reactor designs for smaller electricity grids as may be found in developing or remote regions. The purpose of the OSU MASLWR test facility is to assess the operation of the MASLWR under normal full operating pressure and full temperature conditions and to assess the passive safety systems under transient conditions. The data generated by the testing program will be used to assess computer code calculations and to provide a better understanding of the thermal-hydraulic phenomena in the design of the MASLWR NSSS. During this testing program, four tests were conducted at the OSU MASLWR test facility. These tests included one design basis accident and one beyond design basis accident. During the performance of these tests, plant operations to include start up, normal operation and shut down evolutions were demonstrated successfully.     

Microstructural development and creep deformation in equiaxed γ, γ+α 2, and γ+α 2+B2 titanium aluminides

The development of microstructure and its influence on creep properties have been studied for structures including equiaxed γ, duplex, and other structures of varying α ₂ morphology in two Ti-48Al-2Cr-2Nb alloys. Heat treatments at 1125 °C have been utilized to produce equiaxed γ microstructures in alloys with or without Mo additions. The γ → α transformation produces α ₂ plates with several orientation variants within γ grains during subsequent annealing of the equiaxed γ microstructures below the α transus. Formation of this α ₂ morphology results from rapid up-quenching (UQ), and this structure persists through annealing, cooling, and creep testing. Differences in minimum creep rates for several microstructures containing varying amounts of multi- or single variant γ/α ₂ grains are shown to be minimal. The presence of Mo has also resulted in improved creep resistance in equiaxed γ and γ+α ₂+B2 structures, as compared to similar microstructures in the Ti-48Al-2Cr-2Nb alloy. Deformation during creep at 760 °C at stresses between 200 and 400 MPa occurs by a combination of twinning and dislocation glide without recrystallization, resulting in power-law stress exponents in the range of 6 to 9. Only minimal strain path dependence of the minimum creep rate is detected in a comparison of creep rates in stress jump, stress drop, and single stress tests. This article is based on a presentation made in the symposium “Fundamentals of Gamma Titanium Aluminides,” presented at the TMS Annual Meeting, February 10–12, 1997, Orlando, Florida, under the auspices of the ASM/MSD Flow & Fracture and Phase Transformations Committees.     

Deformation and fracture of urethane–methacrylate resins

The tensile properties of three urethane–methacrylate resins that varied in the soft segment content of the urethane were characterized. The strain birefringence at a circular hole was observed during loading–unloading cycles to progressivley higher displacements. The shear strain distribution at the hole was calculated from the isochromatic fringe contours and compared with results from linear elastic analysis. When the onset of nonlinearity, and the subsequent appearance of residual strain at the root of the hole, were correlated with features of the macroscopic stress-displacement curves, three regions of prefracture deformation were defined. A region of linear elastic behavior was observed at the lowest strains. The maximum shear strain at the linear limit was the same in all the resins, and appeared to correlate with the yield condition at the hole. When the shear strain at the hole exceeded about 2.8%, the fringe patterns started to deviate from the elastic prediction. However, strain was fully recoverable in this region as indicated by the absence of residual birefringence at the hole after unloading. This region of nonlinear, recoverable deformation extended to progressively higher strains as the amount of urethane soft segment increased. This feature was attributed to the network structure of the urethane–methacrylate resins. A region characterized by nonrecoverable deformation at the hole followed at higher strains; the urethane soft segment content had a major effect on the amount of permanent deformation sustained before fracture. The fracture surfaces exhibited features typical of brittle fracture without crazing. © 1995 John Wiley & Sons, Inc.     

Evidence of successful river spawning by lake trout (Salvelinus namaycush) in the Lower Niagara River,Lake Ontario

Restoration of a wild-produced lake trout Salvelinus namaycush population in Lake Ontario has not been successful despite the adult population often meeting or exceeding restoration targets. Lack of high-quality spawning habitat in Lake Ontario is suggested as one impediment to recruitment of wild lake trout, although the quantity and location of spawning habitat is poorly understood. If high-quality spawning habitat is limited in Lake Ontario, lake trout may be using uncommon spawning locations such as rivers. Anecdotal angler accounts point to the Niagara River as a lake trout spawning location. To better understand the potential of the Niagara River as a spawning location, egg and juvenile fish collections were conducted 12–14 river kilometers from the mouth of the Niagara River from 2010 to 2012; and mature female lake trout with surgically implanted acoustic tags were monitored from 2015 to 2019. Genetic analyses confirmed 60% of collected eggs and 93% of collected post-hatch juvenile fish in the Niagara River were lake trout. Tagged female lake trout returned to the Niagara River over consecutive years during the spawning season. The short duration of lake trout presence in the river (mean = 56 days/year) suggests female lake trout use the Niagara River primarily for spawning. Diversity in spawning locations may provide lake trout population’s resilience against environmental variability through a portfolio effect. Improved identification of riverine spawning locations, including their overall contribution to wild recruitment, may be a useful tool for managers to restore a wild-produced population of lake trout in Lake Ontario.     

Intelligent monitor for typhoon in IoT system of smart city

The Journal of Supercomputing - Accidents often occur in the earth—typhoons, floods, earthquakes, traffic accidents and so on. Whether these accidents can be timely and effectively responded...     

Correction to: Non-congruent non-degenerate curves with identical signatures

Journal of Mathematical Imaging and Vision - A correction to this paper has been published: https://doi.org/10.1007/s10851-021-01028-0     

A Model of Weekly Labor Participation for a Belgian Synthetic Population

This paper presents a model of labor participation calibrated on a weekly basis; part-time and full-time employments are also considered. By applying the theory of random utility maximization we model households’ choices. In order to have a good temporal and spatial coverage the model is calibrated on three datasets, extracted from both national and regional travel surveys. The results are applied to synthetic households that reproduce the Belgian population. The proposed innovative methodology simulates synthetic agents by accounting both for households’ and individuals’ characteristics, while not suffering from the problem of the “zero cell value”. The results indicate that there is major day-to-day variability in working activity participation; in particular, on Wednesdays and Fridays the number of households working part-time or not working is particularly high. This is consistent with what was expected by the analysts. Working participation is a fundamental component in activity based models where work is considered a skeletal activity. The tools developed here can be useful to study how changes in population characteristics (i.e. increases of flexible working arrangements and of the number of women in the work force) affect activity participation and travel patterns.