林业资源热解气化供热发电产业发展趋势与战略对策

生物质热解气化供热发电是林业资源加工剩余物高效综合利用产业。我国林业加工废弃物可利用量约为2.1亿吨/年,利用可再生林业资源供热和发电,有助于改善我国能源结构,增强能源安全保障,提升我国节能减排水平,推动社会主义新农村建设,促进林业可持续发展。针对目前林业资源气化供热发电产业发展过程中普遍存在的原料收储运存在瓶颈、生产过程自动化和智能化水平不高、标准化生产技术不成熟、高值化和综合利用技术缺乏等问题,建议加强林业特色资源林基地建设、创新分布式产业发展模式、突破卡脖子技术难题、严格市场准入审批、加强政府管理和行业规范、加大政策扶持力度,力争建立原料供应稳定、高品质燃气绿色制造和生物炭高效应用的一体化产业体系,到2035年气化产业年利用林业剩余物超过500万吨标准煤,总产值达100亿元/年。     

固溶冷却介质对GH4720Li合金组织和性能的影响

γ'相的形貌对GH4720Li合金的性能起着十分重要的作用。固溶淬火时高冷速可以增加基体的过饱和度,有利于获取细小的γ'相组织,然而过高的冷速容易导致工件淬火开裂。因此,工业生产中选择适当的冷却介质控制固溶淬火的冷却速度就显得尤其关键。采用光学显微镜(OM)、扫描电镜(SEM)等手段研究了不同冷却介质对GH4720Li合金组织和性能的影响。结果显示,固溶冷却介质对GH4720Li合金的晶粒尺寸、一次γ'相形貌和数量无影响;水冷试样中二次γ'相的数量最少、三次γ'相的尺寸最小;水溶性淬火剂(20%浓度)冷却后的样品中三次γ'相的尺寸最大,室温、高温拉伸的屈服强度略低于其他样品。     

铀钼矿硫酸焙烧过程动力学与熟料浸出研究

对于难处理铀钼矿而言,硫酸焙烧法可有效活化铀、钼组分并实现高效提取。焙烧过程正交试验结果表明,焙烧温度和焙烧时间对铀、钼浸出率均有较大影响,而酸矿质量比对铀浸出率影响更显著,硫酸浓度对钼浸出率影响更大。TG/DTG分析表明,整个焙烧过程可分为3个阶段：27.4～66.7、66.7～141.1、141.1～267.3 ℃;对应的Kissinger微分法反应活化能分别为17.592、16.878、38.660 kJ/mol。硫酸焙烧熟料浸出优化工艺参数为：浸出温度80 ℃、浸出时间3 h、液固体积质量比5 mL/g。     

铝酸钠溶液中钒酸盐的析出行为研究

以氧化铝生产流程中氢氧化铝的洗涤液为原料,研究了苛性碱浓度、反应温度及反应时间对溶液中钒酸盐析出情况的影响。结果表明,钒酸盐的析出率随苛性碱浓度的升高和反应时间的延长而增大,随反应温度的升高而减小。当铝酸钠溶液的苛性碱浓度为200g/L、反应温度为30℃、反应时间为72h时,溶液中的钒元素可减少60%以上。结晶析出的钒酸盐主要为钒酸钠和偏钒酸钠,其晶体结构为八面体。     

特种冶金生产流程的发展趋势

特种冶金是生产高端特殊钢和特种合金的主要手段,代表了一个国家的工业化发展水平,一直是国内外冶金技术竞争的制高点.本文首先回顾和总结了传统特种冶金技术的种类和主要生产流程;其次,概述了典型特殊钢品种的特种冶金生产流程;再次,对典型特钢企业的特种冶金生产流程进行了介绍;最后,对特种冶金生产流程的未来发展趋势作出预测.新技术将进一步促进特种冶金生产流程的变革与发展.     

Influence of Five-Year Degradation on Mechanical and Tribology Properties of Ultra-High-Molecular-Weight Polyethylene

Ultra-high-molecular-weight polyethylene (UHMWPE) has been the most commonly used bearing material in total joint replacement. The degradation of UHMWPE components has a notable influence on its mechanical properties. UHMWPE samples were immersed in simulated fluid (SBF) up to 5 years and the change in chemical composition and mechanical and wetting properties was investigated. It was found that the oxygen/carbon (O/C) ratio and crystallinity increased from 14.5 and 50.0% before immersion to 52.8 and 60.7% after immersion in SBF for 5 years, respectively. These resulted in a reduction in ball indentation hardness, scratch coefficient, peak load, and contact angle by 35.7, 21.0, 15.8, and 14.0%, respectively, after 5 years of immersion. The steady-state friction coefficient and wear rate increased 83.3 and 43.8%, respectively, after immersion in SBF for 5 years. The preliminary study indicated that the scratch test was an effective method to evaluate the surface performance of UHMWPE after short-term degradation, and small punch test was often used to assess the bulk properties of UHMWPE after long-term degradation.     

Numerical study of geometrical effects on the performance of an H-type cylindrical resonant photoacoustic cell

We have numerically studied the geometrical effects on the performance of an H-type cylindrical resonant photoacoustic cell, composed of one resonator and two symmetrical buffer cylinders, by performing simulations on the generation of acoustic waves in the cell. Here, the acoustic response (pressure), resonance frequency and quality factor are calculated for the cell performance, while the lengths and diameters of both resonator and buffer cylinders are considered for the geometrical parameters or dimensions. Our calculation solves linearized forms of the continuity equation, Navier-Stokes equation, energy equation, and equation of state using a finite element method under an assumption that the heat addition due to the laser passage and thus the variations in the velocity, pressure and temperature fields inside the cell are small enough. First, we performed a statistical analysis using a design of experiment method to evaluate the relative impacts of the cell dimensions on the acoustic response. Subsequently, we performed a parametric study to quantify the cell performance with the dimensional variations. Our results, along with the response surface methodology, provide guidance for a systematic design optimization of the cell for the best acoustic response. The approach in this study may be applied to the design of various types of resonant photoacoustic spectroscopy devices.     

Finite element analysis of the impact of liner thickness and hydrodynamic limit on the penetration depth of a shaped charge warhead

In this work, an identification method for the hydrodynamic limit of shaped charge jets (SCJs) is proposed using numerical analysis. To identify the hydrodynamic limit, we consider situations where two targets of the same density but different strengths are penetrated by the same SCJ. As a result, the SCJ corresponding with the hydrodynamic theory is a jet region with a velocity larger than 4 km/s. In addition, an investigation based on the hydrodynamic limit and liner thickness indicates that the penetration capability before and after the hydrodynamic limit improves as apex thickness decreases and base thickness increases, respectively. The simple and clear identification of the hydrodynamic limit is expected to be possible using the proposed method. Accordingly, a selective and organized liner thickness design can be developed.

     

An improved thermal model for characteristics analysis of multi-link ultra-precision press system

Journal of Mechanical Science and Technology - In traditional models, only the effect of temperature change of bearings on the heat generation power and thermal contact resistance is considered....     

Lyapunov exponent of friction-induced vibration under smooth friction curve

This paper studies the nonlinear behavior of the friction-induced vibration by using spring-mass model subject to the smooth frictionvelocity curve. The nonlinearity and instability of the friction may produce the chaotic vibration depending on the friction curve. In order to show this, the Lyapunov exponents are calculated for a variety of the slope and magnitude in the smooth friction curve. In turn, the dependency of the friction curve on the chaotic attractor is illustrated.