Study of the Enhancement of the Efficiency of the Monocrystalline Silicon Solar Cell by Optimizing Effective Parameters Using PC1D Simulation

Silicon - In this paper, simulation of a monocrystalline silicon solar cell was done using PC1D software. The impact of different solar cell parameters, with their effects on power and efficiency,...     

Value analysis of intermittent generation sources from the systemoperations perspective

The objective of this study is to determine the economic and operational impact on energy cost of incorporating large photovoltaic (PV) and wind energy conversion systems (WECS) into the electric utility generation mix. In most cases, PV and WECS power outputs are subtracted from the utility load with the expectation that conventional generation would meet the residual load. This approach is valid for small penetration levels and/or for PV and WECS facilities connected near load centers, However, several constraints such as thermal generation characteristics, fuel supply and delivery, spinning reserve requirements, and hydro availability are not adequately represented in this process. To determine the optimal value of large-scale PV and WECS applications, a new methodology that would take into account the aforementioned constraints as well as a more global penetration is developed. Results indicate that while high hydro availability increases PV penetration levels, high ramping rates can also significantly increase penetration levels     

Comparing the Effectiveness of Coatings on Carbide andCermet Cutting Tool Inserts

A series of metal cutting experiments was performed on a CNC lathe to evaluate the performance of various coatings on different tool substrates. The workpiece material was plain medium carbon steel and the cutting tool materials were carbide and cermet inserts coated with various single as well as multilayer coatings. Machining was done under various cutting conditions of speed and feed-rate, and for various durations of Cutting. The output parameters studied were the cutting forces (axial, radial and tangential), the surface roughness of the workpiece, as well as the tool wear (crater and flank wear). From these results, the performances of the various cutting inserts are evaluated and compared. Results show that cutting forces are significantly lower when using coated cermets than when using coated carbides although different coatings on the same substrate also result in different cutting forces. However, there is less difference in the surface roughness of the finished workpiece for the various coatings and substrates.     

Analytical, numerical and experimental investigations of transverse fracture propagation from horizontal wells

This paper presents results of a comprehensive study involving analytical, numerical and experimental investigations into transverse fracture propagation from horizontal wells. The propagation of transverse hydraulic fractures from horizontal wells is simulated and investigated in the laboratory using carefully designed experimental setups. Closed-form analytical theories for Mode I (opening) stress intensity factors for idealized fracture geometries are reviewed, and a boundary element-based model is used herein to investigate non-planar propagation of fractures. Using the mixed mode fracture propagation criterion of the model, a reasonable agreement is found with respect to fracture geometry, net fracture pressures and fracture propagation paths between the modeled fractures and the laboratory tested fractures. These results suggest that the propagation of multiple fractures requires higher net pressures than a single fracture, the underlying reason of which is theoretically justified on the basis of local stress distribution.     

Prony-Based Optimal Bayes Fault Classification of Overcurrent Protection

The development of deregulation and demand for high-quality electrical energy has lead to a new requirement in different fields of power systems. In the protection field, this means that high sensitivity and fast operation during the fault are required while maltripping of relay protection is not acceptable. One case that may lead to a maltrip of the high-sensitive overcurrent relay is the starting current of the induction motor or inrush current of the transformer. This transient current has the potential to affect the correct operation of protection relays close to the component being switched. In the case of switching events, such transients must not lead to overcurrent relay operation; therefore, a reliable and secure relay response becomes a critical matter. Meanwhile, proper techniques must be used to prevent maltripping of such relays, due to transient currents in the network. In this paper, the optimal Bayes classifier is utilized to develop a method for discriminating the fault from nonfault events. The proposed method has been designed based on extracting the modal parameters of the current waveform using the Prony method. By feeding the fundamental frequency damping and ratio of the 2nd harmonic amplitude over the fundamental harmonic amplitude to the classifier, the fault case is discriminated from the switching case. The suitable performance of this algorithm is demonstrated by simulation of different faults and switching conditions on a power system using PSCAD/EMTDC software.     

Swift and Selective Reduction of Nitroaromatics to Aromatic Amines with Ni–Boride–Silica Catalysts System at Low Temperature

Various nitroaromatics are successfully reduced to amines with 100% conversion and selectivity in methanol at low temperature (≈5 °C), by using versatile system of 5% Ni–SiO₂ catalyst and NaBH₄ and in situ generation of Ni boride. The catalytic efficiency of Ni loading (5%, 10% and 15%) with silica or titania as support materials is investigated for reduction of nitrobenzene. The Ni–titania/NaBH₄ system recorded lower conversion and selectivity. The IR studies indicate that silica support does not have free –OH group on its surface. Thus the nickel boride is anchored to the silica to facilitate the catalytic process.     

Multilevel optimization applied to hull girder design using three panel forms

A multilevel design scheme for ship's hull girders (longitudinal members between two adjacent transverse frames) is presented in this paper. This design scheme handles, very conveniently, the complexity of using an optimization algorithm for such complex design problems having a large number of design variables, nonlinear constraints dealing with different failure modes and interactions among substructures, and nonlinear design objectives. The conventional multilevel design technique is modified by introducing an approach called constraint coordination to increase the probability of achieving the overall optimum very efficiently.The scheme is demonstrated by application to the structural design of hull girders with simple structural modelling to represent inland waterway ships on which there was a special emphasis in the original research project (Rahman 1991). Three possible panel (consisting of one stiffener and its attached plating) forms; tee stiffened, flat-bar stiffened and corrugated, are optimized to synthesize the hull girder in order to achieve the most efficient structure. The effect of price-structure (labour rate to material price ratio) on the design is also investigated.     

Cyclobutanones as markers for irradiated samples of Brie and Camembert cheese

The feasibility of applying a chemical method based on the formation of 2-alkylcyclobutanone to samples of irradiated soft cheese (Brie and Camembert) was investigated. Significant quantities of 2-dodecylcyclobutanone (DCB) and 2-tetradecylcyclobutanone (TCB) were detected in both types of irradiated cheese and are proposed as qualitative markers. Other members of the cyclobutanone family (decyl- and tetradecenyl-) are also thought to be present but could not be substantiated due to a lack of authentic standards. These compounds were absent from the unirradiated samples. Results also show a significant linear relationship between the irradiation dose (1 to 8 kGy) and the amount of DCB and TCB detected in the cheese.