Effect of nitrogen and nickel on the stability of an Fe-12Cr-23Mn austenitic steel

The effect of nitrogen and nickel on the austenite stability and the structural changes as a result of cold work of an Fe-12Cr-23Mn alloy steel has been examined by transmission electron microscopy and X-ray analysis. Prestrain was performed either at room temperature or at 200° C. Final strain was carried out at liquid nitrogen temperature. The volume fraction of strain-induced martensite decreased by 40% and 12% due to the addition of 2.43% Ni and 0.11% N, respectively, despite whether prestrain was performed or not. The mechanisms are discussed in terms of the phase, stacking faults, dislocation cells and dislocation tangles induced by prestrain and final strain.     

Parallel Algorithms for Image Template Matching on Hypercube SIMD Computers

This correspondence presents several parallel algorithms for image template matching on an SIMD array processor with a hypercube interconnection network. For an N by N image and an M by M window, the time complexity is reduced from O(N2M2) for the serial algorithm to O(M2/K2 + M * log2 N/K + log2 N * log2 K) for the N2K2-PE system (1 ? K ? M), or to O(N2M2/L2) for the L2-PE system (L ? N). With efficient use of the inter-PE communication network, each PE requires only a small local memory, many unnecessary data transmissions are eliminated, and the time complexity is greatly reduced.     

低电压氧化锌压敏电阻器的研究

研究了一种制造低电电压氧化锌压敏电阻器的方法。在基本成分的基础上适当加入二氧化钛可降低梯度电压（Ｖ１ｍＡ／ｍｍ），适量掺硼和改进热处理工艺可减小元件的漏电流和提高其稳定性。     

The Synthesis of Covalent Triazine-Based Frameworks via Friedel–Crafts Reactions of Cyanuric Chloride with Thienyl and Carbazolyl Derivatives for Fluorescence Sensing to Picric Acid,Iodine and Capturing Iodine

A multifunctional thiophene-based covalent triazine framework (TTPATTh) with triphenylamine as core is synthesized by Friedel–Crafts reaction of cyanuric chloride with thienyl derivative for the first time. The yield of TTPATTh (99.59%) is far higher than that of the carbazole-based CTF (TTPATCz, 47.03%). TTPATTh and TTPATCz possess high BET surface areas with 1235 and 2501 m² g^–1 as well as high pore volumes with 1.60 and 2.23 cm³ g^–1, respectively. TTPATTh and TTPATCz have high thermal stability with high thermal decomposition temperatures of 514 and 598 °C in nitrogen atmosphere. With the introduction of triazine rings, the fluorescence sensing sensitivities of TTPATTh and TTPATCz to picric acid and iodine are improved significantly. Especially for TTPATTh, the K_sv values reach 5.95 × 10⁵ and 1.61 × 10⁴ L mol^–1, and LODs reach 1.02 × 10^–12 and 1.86 × 10^–12 mol L^–1. To the best of the knowledge, this is the most sensitive value among thiophene-based porous organic polymers to PA and I₂. Furthermore, TTPATTh and TTPATCz can also adsorb iodine in vapor phase, cyclohexane solution and aqueous solution, and release iodine by heating or in ethanol solution. The efficiency of controlling the release of iodine is higher than that in ethanol.     

Mold-filling characteristics of AZ91 magnesium alloy in the low-pressure expendable pattern casting process

The magnesium (Mg) alloy low-pressure expendable pattern casting (EPC) process is a newly developed casting technique combining the advantages of both EPC and low-pressure casting. In this article, metal filling and the effect of the flow quantity of inert gas on the filling rate in the low-pressure EPC process are investigated. The results showed that the molten Mg alloy filled the mold cavity with a convex front laminar flow and the metal-filling rate increased significantly with increasing flow quantity when flow quantity was below a critical value. However, once the flow quantity exceeded a critical value, the filling rate increased slightly. The influence of the flow quantity of inert gas on melt-filling rate reveals that the mold fill is controlled by flow quantity for a lower filling rate, and, subsequently, controlled by the evaporation of polystyrene and the evaporation products for higher metal velocity. Meanwhile, the experimental results showed that the melt-filling rate significantly affected the flow profile, and the filling procedure for the Mg alloy in the low-pressure EPC process. A slower melt-filling rate could lead to misrun defects, whereas a higher filling rate results in folds, blisters, and porosity. The optimized filling rate with Mg alloy casting is 140 to 170 mm/s in low-pressure EPC.     

不同活化剂对石油焦基活性炭孔结构的影响

以石油焦为原料 ,Na OH,KOH和 Na2 CO3 为活化剂制备活性炭 ,采用氮气吸附考察了不同活化剂对活性炭的比表面积、中孔和微孔孔径分布、孔容积及平均孔径等孔结构的影响 .结果表明 :KOH活化制备的活性炭包含 1 nm的微孔和 4nm的中孔 ,总孔容 0 .648cm3 /g,比表面积大 ;Na OH制备的活性炭以 1 nm的微孔为主 ,占总孔容 ( 0 .1 65 cm3 /g)的 98% ,平均孔径 1 .83nm;Na2 CO3 制备的活性炭以 4nm的中孔为主 ,占总孔容 ( 0 .1 43cm3 /g)的 68.5 % ,平均孔径 3.42 nm,比表面积小 .3种样品的孔径都呈现出多峰分布特征 .KOH和 Na2 CO3 活化制备的活性炭的 N2 吸附脱附曲线属于 型 ,Na OH活化制备的活性炭吸附脱附曲线属于 型 .     

Kynar—500涂装工艺与涂层性能研究

介绍了Kynar－500涂料的涂装工艺，并对涂层的性能作了试验与分析。     

环己烷液相无催化剂的氧化动力学研究

采用搅拌釜反应器,在确认已排除传质因素对反应速率影响的情况下,研究了环己烷液相无催化剂的氧化反应动力学。应用自由基理论及最优化计算技术,从导出的8个候选动力学模型中,确定了最佳的动力学模型,它能满意地描述环已烷氧化过程。该动力学可为环己烷氧化工业生产操作条件的优化、反应器的选型及工业设计提供依据。     

工业废渣磷石膏用作充填材料的研究

研制了以工业废渣磷石膏为基材的充填材料.改性后磷石膏的耐水性大大增强,抗压强度≥0.79 MPa、渗透系数≤1×10-5cm.s-1,并且具有合适的C、Φ值.     

Poly(3‐chlorothiophene) films prepared by the direct electrochemical oxidation of 3‐chlorothiophene in mixed electrolytes of boron trifluoride diethyl etherate and sulfuric acid

3‐Chlorothiophene (CT) was electrochemically polymerized in mixed electrolytes of a boron trifluoride diethyl etherate solution containing 0–20% (by volume) sulfuric acid. The oxidation potentials of the monomer in these media were measured to be only 1.06–1.31 V (vs Ag/AgCl). These values were much lower than that of CT in acetonitrile and 0.1 mol/L (Bu)₄NBF₄ (1.92 V vs Ag/AgCl). Poly(3‐chlorothiophene) (PCT) films with conductivities of 0.1–2 S cm^?1 were obtained. The structure, morphology, and electrochemical behavior of the PCT films also were investigated. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 502–509, 2003