贵冶动力中心二期反渗透系统改造

本文阐述对贵冶动力车间二期反渗透进行改造的成功实践 ,主要从反渗透系统设计、反渗透系统中容易出现的问题及解决方法等进行介绍。     

N,N′-二(β-十八酰氧基)乙基乙二胺二乙酸钠的合成及性能研究

用 N,N′-二羟乙基乙二胺、氯乙酸钠合成了 N,N′-二羟乙基乙二胺二乙酸钠(中间体),中间体再与硬脂酰氯反应制备了一种新型 Gemini 两性表面活性剂 N,N′-二(β-十八酰氧基)乙基乙二胺二乙酸钠。对产物合成条件进行了考察,优化的反应条件为:n(硬脂酰氯):n(中间体)=2.5,溶剂 V(水):V(氯仿)=1:2,pH=9.0～10.0,反应温度15～20℃,反应时间5 h。通过红外光谱和质谱分析确定了产物结构,并测试了产物的表面性能。结果表明,在25℃时,该产物的临界胶束浓度为0.24 mmol/L,临界胶束浓度下的表面张力为35.7 mN/m;即时泡沫高度为250 mm,5 min 后泡沫高度为220 mm;乳化时间为22.48 min(甲苯-水物系)和4.65 min(正己烷-水物系),亲水-亲油平衡值为5.4,等电点为 pH 3.3～6.5。     

天津德景住宅与商业

因：用地为东西向长达470m的长条形，其北侧紧邻城市干道。     

CFD Simulation of Liquid Film Flow on Inclined Plates

A two‐phase flow CFD model using the volume of fluid (VOF) method is presented for predicting the hydrodynamics of falling film flow on inclined plates, corresponding to the surface texture of structured packing. Using the proposed CFD model the influence of the solid surface microstructure, liquid properties and gas flow rate on the flow behavior was investigated. From the simulated results it was shown that under the condition of no gas flow the liquid flow patterns are dependent on the microstructure of the plates, and proper microstructuring of the solid surface will improve the formation of a continuous liquid film. It was also found that liquid properties, especially surface tension, play an important role in determining the thin‐film pattern. However, there are very different liquid film patterns under the action of gas flow. Thinner liquid films break easily, but thicker liquid films can remain continuous even at higher gas flow rates, which demonstrates that all factors affecting the liquid film thickness will affect the liquid film patterns under conditions of counter‐current two‐phase flow.     

Development of an end-point detector for parylene deposition process

Parylene is an emerging material for MEMS. It is an organic material that is grown by using the chemical vapor deposition method at room temperature. The deposition thickness is commonly controlled by the amount of solid-phase dimer loaded in a sublimation chamber. In a conventional deposition machine, the end point of the process is designated by the moment the dimer is exhausted. However, this end-of-process criterion does not offer precise, repeatable control of film thickness. We present the results of the development of an in situ end-point detector for a Parylene chemical vapor deposition process. The detector is based on the thermal transfer principle and can be implemented on commercial parylene deposition systems with minimal system modification. Such a sensor enables a user to stop the deposition when a targeted thickness is reached. The end point detector is very simple to implement on existing parylene deposition systems. A series of such sensors with different target deposition thickness would allow extraction of the actual deposition rate within a deposition run.     

西气东输工程用X70热轧板卷屈服强度检测值波动大的探讨

对西气东输工程用X70热轧板卷检验过程中出的屈服强度σ0.5波动大的情况进行了分析，认为拉伸试样弯曲是主要原因。这一问题可通过反复压平试样，确保试样的平直度以及适当提高钢的强度的方法加以解决。     

Piezoelectric Nanogenerators for Self-Powered Nanodevices

A novel approach converts nanoscale mechanical energy into electric energy for self-powering nanodevices.In our own work, we've used piezoelectric zinc-oxide nanowire (ZnO NW) arrays to demonstrate a novel approach for converting nanoscale mechanical energy into electric energy. Here, we review the fundamental principle behind the nanogenerator, present an approach for improving its performance, and discuss some of the challenges we face in pushing this technology to reach its potential.     

Hydrothermal Synthesis of Magnesium Aluminate Platelets

Magnesium aluminate (MgAl₂O₄) platelets were first synthesized by hydrothermal treatment of γ-AlO(OH) in a magnesium nitrate aqueous solution at 400°C. The platelets are 100–200 nm in width and 25 nm in thickness. The influence of temperature, the anions of the magnesium salt, the amount of magnesium salt, and precursor pH on the formation of such structure was investigated. The experimental results indicated that the anions of the magnesium salt and precursor pH could have a significant influence on the growth of MgAl₂O₄. MgAl₂O₄ formation followed the in situ transformation mechanism, which was the reason why the MgAl₂O₄ crystallites had a platelet morphology.     

ROADM技术发展与标准化研究

本文研究了ROADM的技术优势，主要结构类型，涉及的关键技术以及存在的问题，并分析了当前ROADM标准化进展情况与发展趋势，还介绍了当前设备现状和现网应用情况。     

探索小森

对于小森公司来说，最近几年在中国的销售业绩相当不错，小森印刷机在中国市场的占有率一直在稳步提高。中国的印刷市场正在高速增长，而小森能够取得如此佳绩，最根本的原因是积极应对世界印刷市场发展趋势，把深度满足用户的需求放在了首位，正如小森的企业理念——让客户感动。