Shape memory alloy film damping for smart miniature systems

This paper presents a dynamic analysis of the free and forced vibration of a free-standing bridge of superelastic shape memory alloy TiNiCuCo film with ultra-low fatigue properties and evaluates its versatility for novel miniature scale damping applications. A thermodynamics-based finite element model is used to simulate the evolution of martensite phase fraction during load-induced martensitic phase transformation. The effects of pre-strain, strain rate and excitation load on the hysteresis of stress-strain characteristics are investigated in order to assess damping energies. The analysis is performed under non-isothermal conditions taking into account heat transfer and rate-dependence of release and absorption of latent heat. We show that damping energy can be maximized by applying an optimum pre-strain. A maximum damping capacity of 0.17 is determined for the case of complete stress-strain hysteresis loop during phase transformation.     

Effect of seed layers on low-temperature,chemical bath deposited ZnO nanorods-based near UV-OLED performance

Low-temperature wet chemical bath deposition (CBD) method is one of the most efficient and least hazardous solution-based techniques which is widely employed to grow ZnO NRs. In CBD method, a seed layer is usually deposited on the substrate. In this paper, high quality ZnO and aluminum doped ZnO (AZO) seed layers are sputtered on the indium tin oxide (ITO) coated glass. In continue, aligned ZnO NRs are grown on the AZO and ZnO seed layers via CBD technique. The effect of the growth time and seed layer on the physical properties of as-grown ZnO NRs are investigated. According to the results, the seed layer plays an essential role on the growth orientation and growth rate of the ZnO NRs. The ZnO NRs grown on AZO seed layer are more aligned rather than ZnO seed layer due to their higher texture coefficients. The relative photoluminescence (PL) intensity ratio of near band emission (NBE) to deep level emission (DLE) (I_NBE/I_DLE) for the ZnO NRs grown on AZO and ZnO seed layers are calculated as 7.45 and 2.62, respectively. To investigate the performance of the as-grown ZnO NRs, near ultraviolet organic light-emitting diodes (UV-OLEDs) using ZnO NRs array as n-type material and poly [2-methoxy-5-(2-ethyl-hexyloxy)-1,4-phenylene-vinylene] (MEH-PPV) conjugated polymer as p-type material have been fabricated. The total concentration of traps ($N_t$), the characteristic energies ($E_t$) and the turn-on voltages for the devices with the structures of ITO/AZO/ZnO NRs/MEH-PPV/Al (device A) and ITO/ZnO/ZnO NRs/MEH-PPV/Al (device B) are attained 7.65 × 10¹⁶ and 7.75 × 10¹⁶ cm^?3, 0.232 and 0.206 eV, 23 and 21 V, respectively. Moreover, based on the electroluminescence (EL) spectra, the NBE peaks for device A and B are obtained nearly in the wavelengths of 382 and 388 nm, respectively. Finally, various charge carrier transportation processes of prepared UV-OLEDs have been studied, systematically.     

Hydrodynamics of pulsed spouted beds: Effects of pulsation waveform,amplitude, and frequency

The effect of flow pulsations is studied via a discrete element model on hydrodynamics of spouted bed, which is being used in many important industries like drying processes. Decreased horizontal air percolation and preserving upward momentum, increased particle circulation, increased particle traverse distance, and better homogeneity are resulted from flow pulsations in spouted beds. Among the waveforms studied, square and triangular waveforms differ most and least from steady spouting, respectively. The predictions indicate that the pulsed spouted bed has the potential to enhance both gas and particle motion, hence being useful in drying and other operations.     

Pd(II)/Pd(0) Anchored on Magnetic Organic–Inorganic Hybrid Mesoporous Silica Nanoparticles: A Nanocatalyst for Suzuki–Miyaura and Heck–Mizoroki Coupling Reactions

Journal of Inorganic and Organometallic Polymers and Materials - 3-Chloropropyltrimethoxysilane (CPTMS) was grafted on the surface of silica coated Fe3O4 core (Fe3O4@MCM-41) and then condensed with...     

A systematic study on the effects of synthesis conditions of polyamide selective layer on the CO2/N2 separation of thin film composite polyamide membranes

Different top layer fabrication methods (amine-first, acid-first, spin coating), organic phase solvents (hexane, heptane, mixed hexane/heptane), acid acceptors (triethylamine, sodium carbonate, sodium hydroxide), and surfactant sodium dodecyl sulfate concentrations (0, 0.05, and 0.1 wt%) were utilized to fabricate thin film composite polyamide membranes for CO₂/N₂ separation. The results, according to an L9 orthogonal array of Taguchi approach, showed that employing acid-first method increases both CO₂ permeance and CO₂/N₂ selectivity of the membranes at a feed gas pressure of 3 bars. On the other hand, sodium hydroxide, and triethylamine should be used, as acid acceptors, to maximize CO₂ permeance and CO₂/N₂ selectivity, respectively. Moreover, the use of hexane solvent and 0 wt% surfactant led to maximum permeance, while, hexane solvent and 0.1 wt% surfactant were needed to reach the highest selectivity. The above level setting of synthesis parameters also resulted in the minimum sensitivity of the fabrication process to the noise factors effects. As shown by the analysis of variance, acid acceptor, and organic solvent types were the most influential parameters on CO₂ permeance and CO₂/N₂ selectivity, respectively. The effects of fabrication method and surfactant concentration, as single factors, on permeation/selectivity responses were also investigated.     

Preparation and Characterization of Nanosized Pomegranate Peel-Based Activated Carbon for Application in Pyridine Removal from Aqueous Solution

Theoretical Foundations of Chemical Engineering - Effect of activating procedure on the physic-chemical properties and adsorption performance of activated carbon was investigated. For this,...     

A novel bilayer drug-loaded wound dressing of PVDF and PHB/Chitosan nanofibers applicable for post-surgical ulcers

A novel bilayer nanofibrous wound dressing, with enhanced mechanical properties is successfully fabricated. This membrane, consisted of polyvinylidenefluoride (PVDF) nanofibers for providing tensile strength and polyhydroxybutyrate/chitosan (PHB/CTS) nanofibers loaded with gentamicin with ability of controlled drug delivery, is a great choice for post-surgical ulcers. Mechanical properties showed dramatically improvement of tensile strength by addition of PVDF layer. Gentamycin release represented both an immediate and a sustained release of about 24?h and 1 week, respectively and release increment with increase of CTS ratio. Results also revealed that drug release in structures follow first order kinetic and Fickian release mechanism.     

Spark plasma sintering of Al-doped ZrB2–SiC composite

This research presents the influence of Al addition on microstructure and mechanical behavior of ZrB₂–SiC ultra-high temperature ceramic matrix composite (UHTCMC) fabricated by spark plasma sintering (SPS). A 2.5?wt% Al-doped ZrB₂–20?vol% SiC UHTCMC was produced by SPS method at 1900?°C under a pressure of 40?MPa for 7?min. The microstructural and phase analysis of the composite showed that aluminum-containing compounds were formed in-situ during the SPS as a result of chemical reactions between Al and surface oxide films of the raw materials (i.e. ZrO₂ and SiO₂ on the surfaces of ZrB₂ and SiC particles, respectively). The Al dopant was completely consumed and converted to the intermetallic Al₃Zr and Al₄Si compounds as well as Al₂O₃ and Al₂SiO₅. A relative density of 99.8%, a hardness (HV5) of 21.5?GPa and a fracture toughness (indentation method) of 6.3?MPa?m^1/2 were estimated for the Al-doped ZrB₂–SiC composite. Crack bridging, branching, and deflection were identified as the main toughening mechanisms.     

Facile catalytic ring opening polymerization of lactic acid: Comparing the performance of Fe and Zn metal species

As a bio‐compatible/degradable polymer, poly(lactic acid) (PLA) has been widely noticed in tissue engineering and medical applications. Proper catalytic ring‐opening polymerization of lactic acid is pertinent to development of active metal species capable of producing high‐molecular‐weight polymers. In this work, ligand catalyst (2,4‐di‐tertio‐butyl‐6‐{[(2‐di‐methyl‐amino ethyl) methyl amino] methyl} phenol) was synthesized and then attached to Fe‐based and Zn‐based metal substitutes, and performance of metal species toward ring opening polymerization of lactic acid has been investigated. Regulation of reaction condition at 180°C for 36 h with Zn‐based catalyst allowed for late‐stage production of a high‐molecular‐weight PLA, while Fe‐based facilitated polymerization at early stages leading to PLAs with comparatively twofold higher molecular weight at lower time, monomer‐to‐initiator ratio, and temperature (at 170°C). A ratio of monomer to initiator of 5000 with Fe catalyst resulted in the highest molecular weight. Thus, polymerization has been facilitated by the use of Fe‐based catalyst. For this class of catalyst with Fe substitute, the product was characterized by means of ¹H‐NMR, Fourier transform infrared spectroscopy, and differential scanning calorimetry analyses. J. VINYL ADDIT. TECHNOL., 25:215–224, 2019. © 2018 Society of Plastics Engineers