Ni,Cr, and Fe surfaces corroded by molten ZnCl2

Understanding the corrosion of molten ZnCl₂ on metal surfaces is significant for the corrosion protection of metals, sustainable use of molten salts, preparation of ZnO coatings, and so on. In this paper, surfaces of pure Ni, Cr, and Fe corroded by molten ZnCl₂ were investigated. The results show that Ni suffered very slight corrosion, while Cr experienced more serious corrosion than Ni, but lighter corrosion than Fe. The morphology of the corrosion of Cr and Fe, respectively, presented pitting and intergranular corrosion characteristics. Furthermore, nanostructured ZnO coatings were obtained on the surfaces of Ni and Fe, but not on the surface of Cr. The ZnO coating on the Ni surface was doped with a small amount of Zn₅(OH)₈Cl₂, and the ZnO coating on the Fe surface was doped with ZnFe₂O₄ and Zn₂OCl₂. The coatings on the Ni and Fe surfaces had an average thickness of 1.5 and 50 μm, respectively.     

Single-Crystalline TiO2(B) Nanobelts with Unusual Large Exposed {100} Facets and Enhanced Li-Storage Capacity

The {100} facet of single-crystalline TiO₂(B) is an ideal platform for inserting Li ions, but it is hard to be obtained due to its high surface energy. Here, the single-crystalline TiO₂(B) nanobelts from H₂Ti₃O₇ with nearly 70% {100} facets exposed are synthesized, which significantly enhances Li-storage capacity. The first-principle calculations demonstrate an ab in-plane 2D diffusion through the exposed {100} facets. As a consequence, the nanobelts can significantly accommodate Li ions in LiTiO₂ formula with specific capacity up to 335 mAh g⁻¹, which is in good agreement with the electrochemical characterizations. Coating with conductive and protective poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate), the cut-off discharge voltage is as low as 0.5 V, leading to a capacity of 160.7 mAh g⁻¹ after 1500 cycles with a retention rate of 66% at 1C. This work provides a practical strategy to increase the Li-ion capacity and cycle stability by tailoring the crystal orientation and nanostructures.     

含煤盆地深层“超饱和”煤层气形成条件

中国深层煤层气资源丰富，但总体勘探和认识程度较低，尚未形成较为系统的深层煤层气地质理论。通过解剖分析准噶尔盆地白家海凸起和鄂尔多斯盆地临兴区块深层"超饱和"煤层气井的试气/生产动态，估算原地游离气的含气量，分析了深层"超饱和"煤层气的形成条件。研究表明：①深层"超饱和"煤层气储层中除吸附气外，还含有原地游离气，用常规试气方法可直接获得气流，煤层气的产出不明显依赖于排水降压；②埋藏超过一定深度，在煤阶和温度的综合作用下，煤的吸附能力将随埋深的继续增加而降低，煤层中吸附气的饱和度有增加的趋势，在达到吸附饱和后，出现原地游离气并形成"超饱和"煤层气，盆地深层具有"超饱和"煤层气形成的优势条件；③由于地温梯度和压力梯度的不同，不同盆地"超饱和"煤层气出现的临界深度不同，异常高压和异常高热流可以降低深层"超饱和"煤层气形成的临界深度；④深层"超饱和"煤层气开发具有大大缩短见气时间、充分利用地层能量和累积产水量低等优势，有望成为未来煤层气勘探开发的一个重要领域。     

浅谈大断面巷道掘进技术的实践与体会

该文针对当前矿井炮掘巷道大断面掘进普遍存在掘进施工较慢的实际,结合公司实际情况,有针对性地提出了解决的办法。     

Operating Range Scheduled Robust Dahlin Algorithm to Typical Industrial Process with Input Constraint

International Journal of Control, Automation and Systems - There is a class of typical nonlinear industrial process, which can be characterized by a first-order inertia plus pure delay model in an...     

Multi-objective layout optimization for an orbital propellant depot

Structural and Multidisciplinary Optimization - The overall layout optimization design of an orbital propellant depot involves the optimization of shape, size, and positions of propellant tanks in...     

铝合金热轧板锭熔铸技术及设备

本文概述了近年来铝合金热轧板锭的熔铸设备和熔铸技术的发展和最新成就，重点介绍晶粒细化、熔体净化、检测及铸造新技术，为国内铝板带企业跟踪国际铝合金板锭熔铸技术、开展技术攻关和进行技术创新提供有益的参考。     

加氢催化剂预硫化技术进展

阐述了加氢催化剂预硫化的方法和预硫化对加氢催化剂的作用,介绍了国外公司在加氢催化剂器外预硫化技术领域的发展近况,同时对国内相关单位在该领域的技术现状作了具体论述。     

以IBAC为核心处理洗浴废水的试验研究

根据洗浴废水的水质特征,采用原水→混凝沉淀-过滤→固定化生物活性炭(Immobilized Biological Activated Carbon,IBAC)→微滤膜(MF)→UV消毒→出水的工艺流程.混凝沉淀-过滤物化预处理单元可以有效地减少洗浴废水中的各类污染物.IBAC生化处理单元,实现有机污染物、LAS、浴臭等有效去除,是保证出水合格的根本措施.微滤膜发挥物理截留作用、UV消毒杀死细菌和总大肠菌群.出水水质达到＜城市供水水质标准＞(CJ/T 206-2005).