Nanoporous microtubes obtained from a Cu-Ni metallic wire

Nanoporous microtubes of a nickel-copper alloy were obtained from a Cu-44Ni-1Mn (wt%) commercial wire (200 μm diameter). A new synthesis method was established through three steps: 1) partial oxidation of the wire at 1173 K in air, 2) removal of the inner unoxidized core by chemical etching, 3) reduction in 10 bar hydrogen atmosphere. During oxidation, the segregation of Cu and Ni occurred because of their different diffusion coefficients in the corresponding oxides. As a consequence, pores were formed by Kirkendall effect and due to selective chemical etching of the different oxides. Additional porosity formed because of volume contraction during reduction with hydrogen. After reduction, the microtube shows a composition gradient from the inner wall (almost pure nickel) to the outer wall (almost pure copper). The process allowed to obtain microtubes with tuneable wall thickness and inner pores around 180 ± 80 nm. The morphological features developed suggest improved capillarity properties for applications in MEMS.     

Effects of the indentation process on fatigue life of drilled specimens: optimization of the distance between adjacent holes

The generation of permanent compressive stresses around the holes is recognized as a valuable mean to delay the onset and propagation of the defects and to extend the fatigue life of the mechanical components. In the work, a bilateral indentation process, performed on each side of the component, is widely used in order to create a residual circumferential stress field around the area to be drilled and that persists after the drilling operation. In order to evaluate the process parameters and to identify optimal geometric solutions, several static and fatigue tests are conducted on AW 6082-T6 aluminum alloy specimen where two holes are created. In particular, experimental tests on only drilled specimens (OD) and specimens subjected to Indentation process (IP) varying the indentation depth and the center-tocenter distance of the holes are performed. Several numerical analyses, conducted in ANSYS APDL environment with explicit solver, allow to determine the influence of the distance between two adjacent holes and the effect of the indentation depth on the residual stress distribution.     

A distributed command governor based on graph colorability theory

In this paper, a distributed command governor (CG) strategy is introduced that, by the use of graph colorability theory, improves the scalability property and the performance of recently introduced distributed noncooperative sequential CG strategies. The latter are characterized by the fact that only 1 agent at a decision time is allowed to update its command, whereas all the others keep applying their previously computed commands. The scalability of these early CG distributed schemes and their performance are limited because the structure of the constraints is not taken into account in their implementation. Here, by exploiting the idea that agents that are not directly coupled by the constraints can simultaneously update their control actions, the agents in the network are grouped into particular subsets (turns). At each time instant, on the basis of a round‐robin policy, all agents belonging to a turn are allowed to update simultaneously their commands, whereas agents in other turns keep applying their previous commands. Then, a turn‐based distributed CG strategy is proposed and its main properties are analyzed. Graph colorability theory is used to determine the minimal number of turns and to distribute each agent in at least a turn. A novel graph colorability problem that allows one to maximize the frequency at which agents can update their commands is proposed and discussed. A final example is presented to illustrate the effectiveness of the proposed strategy.     

Some recent advances in polyolefin functionalization

Polyolefin‐based materials are increasingly being used in many industrial applications for packaging, automotive and construction materials. The recent developments of research have been aimed at making these materials, often complex, being mixtures, block copolymers, micro‐ and nanocomposites with inorganic and organic fillers, more efficient and environmentally friendly (through recycling processes, and the use of bio‐polyolefins). In this context, functionalized polyolefins, on the one hand, play a fundamental role in improving the morphology and thus the thermal and mechanical properties of heterophase systems, and, on the other hand, provide new materials difficult to obtain by conventional synthesis in connection with the type of inserted functionality. Therefore it appears to be of interest to report and discuss here the recent results concerning the radical grafting in the melt of different functionalities onto polyolefins as well as the capability reached of modulating ad hoc the degree of grafting and the final structure/architecture of functionalized polyolefins. © 2013 Society of Chemical Industry     

The influence of process-oriented organisational design on operational performance and innovation: a quantitative analysis in the financial services industry

Market competition requires that organisations excel at both operational performance and innovation. Though process orientation is intended to benefit operations in general, the impact of specific elements remains unclear. The purpose of this study is to identify the specific organisational design components of process orientation that simultaneously influence operational performance and innovation. We survey employees in the financial services sector (N = 1069) regarding the influence of six process-oriented organisation design components on operational performance and innovation using PLS-SEM. The results indicate that organisational structure and process improvement encourage both operational performance and innovation. Personal autonomy is partially beneficial, while the others have no joint influence on operational performance and innovation. This study is first in providing evidence regarding the influence of a broad variety of organisational design components of process orientation on operational performance and innovation. The study contributes to theory on how process orientation improves operational performance and innovation. The findings can serve as a guideline for managers and organisations as to which organisational design components should be implemented to improve operations.     

Predicting mode-II delamination suppression in z-pinned laminates

A finite element model for predicting delamination resistance of z-pin reinforced laminates under the mode-II load condition is presented. End notched flexure specimen is simulated using a cohesive zone model. The main difference of this approach to previously published cohesive zone models is that the individual bridging force exerted by z-pin is governed by a specific traction-separation law derived from a unit-cell model of single pin failure process, which is independent of the fracture toughness of the unreinforced laminate. Therefore, two separate traction-separation laws are employed; one represents unreinforced laminate properties and the other for the enhanced delamination toughness owing to the pin bridging action. This approach can account for the so-called large scale bridging effect and avoid using concentrated pin forces in numerical models, thus removing the mesh-size dependency and permitting more accurate and reliable computational solutions.     

Adsorption of pharmaceuticals from aqueous solutions on synthetic zeolites

The objectives of this study were to measure the sorption capacity of a dilute solution of drugs in water on hydrophobic zeolites and to quantify aspects of their adsorption mechanisms for potential use in wastewater remediation. The removal of three drugs, erythromycin (ERY), carbamazepine (CBZ) and levofloxacin (FLX) from water using three organophilic zeolites (Y, mordenite (MOR), ZSM-5) was investigated. Adsorption isotherms show that these three drugs are adsorbed in remarkable amounts by Y. These data were confirmed by thermogravimetric analysis. The presence of these drugs inside the Y cage was revealed by unit cell parameter variations and structural deformations obtained by X-ray structure analyses carried out using the Rietveld method on zeolite after adsorption. Our results indicate that the adsorption properties of zeolitic materials do not only depend on micropore size and that zeolite shape selectivity also depends on structural features which are difficult to determine “a priori”. In order to test the ability of organophilic zeolites in removing drugs from wastewater, the adsorption of ERY, FLX and CBZ on zeolite Y from water samples collected at the outlet of a wastewater treatment plant located in Northern Italy was determined. These drugs were almost completely adsorbed by Y zeolite, confirming that this material is suitable for removing drugs from wastewater.     

A simulative approach for evaluating alternative feeding scenarios in a kanban system

In accordance with the lean production philosophy, an assembly line may be supplied by means of a kanban system, which regulates and simplifies the flow of materials between the lines and the warehouses. This paper focuses on evaluation of feeding policies that differ from each other in term of the number of kanbans managed per feeding tour. A pure cost-based approach is thus proposed, which considers both inline inventories along with handling costs proportionate to the number of operators involved in the parts-feeding process. A multi-scenario simulative approach is applied in order to establish the number of operators required to avoid inline shortages. The scenario minimising total cost is then selected. The innovation introduced is a model for describing kanban arrivals and their requests for feeding, improving the potential of the simulation to describe real-life environments. Lastly, a case study from the automotive industry is presented in order to highlight the applicability of the proposed approach as well and the effects of alternative feeding policies on the total cost incurred.     

Proteome Analysis of Subsarcolemmal Cardiomyocyte Mitochondria: A Comparison of Different Analytical Platforms

Mitochondria are complex organelles that play critical roles in diverse aspects of cellular function. Heart disease and a number of other pathologies are associated with perturbations in the molecular machinery of the mitochondria. Therefore, comprehensive, unbiased examination of the mitochondrial proteome represents a powerful approach toward system-level insights into disease mechanisms. A crucial aspect in proteomics studies is design of bioanalytical strategies that maximize coverage of the complex repertoire of mitochondrial proteins. In this study, we evaluated the performance of gel-based and gel-free multidimensional platforms for profiling of the proteome in subsarcolemmal mitochondria harvested from rat heart. We compared three different multidimensional proteome fractionation platforms: polymeric reversed-phase liquid chromatography at high pH (PLRP), sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE), and isoelectric focusing (IEF) separations combined with liquid chromatography-mass spectrometry/mass spectrometry (LC-MS/MS), and bioinformatics for protein identification. Across all three platforms, a total of 1043 proteins were identified. Among the three bioanalytical strategies, SDS-PAGE followed by LC-MS/MS provided the best coverage of the mitochondrial proteome. With this platform, 890 proteins with diverse physicochemical characteristics were identified; the mitochondrial protein panel encompassed proteins with various functional roles including bioenergetics, protein import, and mitochondrial fusion. Taken together, results of this study provide a large-scale view of the proteome in subsarcolemmal mitochondria from the rat heart, and aid in the selection of optimal bioanalytical platforms for differential protein expression profiling of mitochondria in health and disease.