Experimental studies of the bond response of three-wire strands and some influencing parameters

The bond behavior of prestressing strands is of great importance for the capacity of precast prestressed concrete structures. In the present study, the bond behavior of three-wire strands, and some influencing parameters, were examined by means of steel encased pull-through and push-in tests. The three mechanisms: adhesion, friction and other mechanical actions were found to be present at the strand-concrete interface at different slip values. The results from the experiments showed that the micro roughness of the strand surface strongly affected the initial bond response of the strand, that is the adhesion in the interface. The maximum bond capacity of indented three-wire strands was found to be directly connected to the geometric properties of the strand indents. The influence of the concrete strength on the bond capacity of the strand was hard to interpret. However, the density of the concrete matrix was found to be a better parameter for determine the influence of the concrete rather than the compressive strength.     

High-resolution images from low-resolution compressed video

Surveys the field of super resolution (SR) processing for compressed video. The introduction of motion vectors, compression noise, and additional redundancies within the image sequence makes this problem fertile ground for novel processing methods. In conducting this survey, though, we develop and present all techniques within the Bayesian framework. This adds consistency to the presentation and facilitates comparison between the different methods. The article is organized as follows. We define the acquisition system utilized by the surveyed procedures. Then we formulate the HR problem within the Bayesian framework and survey models for the acquisition and compression systems. This requires consideration of both the motion vectors and transform coefficients within the compressed bit stream. We survey models for the original HR image intensities and displacement values. We discuss solutions for the SR problem and provide examples of several approaches.     

High slew-rate CMOS operational amplifier

A 0.8 /spl mu/m CMOS operational amplifier configuration with a slew rate in excess of 2 V/ns and a unity gain bandwidth of 55 MHz with a load capacitance of 15 pF is proposed. This employs a dynamic technique that turns on a large current source when the rate of change of input is larger than a pre-decided value.     

Metalorganic chemical vapor deposition of silver thin films for future interconnects by direct liquid injection system

Deposition of Ag films by direct liquid injection-metal organic chemical vapor deposition (DLI-MOCVD) was chosen because this preparation method allows precise control of precursor flow and prevents early decomposition of the precursor as compared to the bubbler-delivery. Silver(I)-2,2-dimethyl-6,6,7,7,8,8,8-heptafluoro-3,5-octanedionato-triethylphosphine [Ag(fod)(PEt₃)] as the precursor for Ag CVD was studied, which is liquid at 30 °C. Ag films were grown on different substrates of SiO₂/Si and TiN/Si. Argon and nitrogen/hydrogen carrier gas was used in a cold wall reactor at a pressure of 50–500 Pa with deposition temperature ranging between 220 °C and 350 °C. Ag films deposited on a TiN/Si diffusion barrier layer have favorable properties over films deposited on SiO₂/Si substrate. At lower temperature (220 °C), film growth is essentially reaction-limited on SiO₂ substrate. Significant dependence of the surface morphology on the deposition conditions exists in our experiments. According to XPS analysis pure Ag films are deposited by DLI-MOCVD at 250 °C by using argon as carrier gas.     

The anisotropic effect of a weak magnetic field on the photoconductivity of C<Subscript>60</Subscript> single crystals

The effect of crystal orientation on the photogeneration of free charge carriers was studied for C₆₀ single crystals in a weak magnetic field. The photoconductivity sharply depends on the orientation of magnetic field with respect to the crystallographic directions, showing a 5–8% increase for seven axes of the C₆₀ crystal.     

State of polarization changes: Classification and measurement

We propose a standardization procedure that provides a convenient, quantitative and reproducible laboratory-based method for measuring the state of polarization (SOP) fluctuations produced by polarization varying devices. This method is based on the SOP distributions generated by commercial polarization scramblers. We show that these devices generate distributions of the maximum change of the SOP (in a given sample time) that follow Rayleigh statistics, which scale linearly with scrambling frequency and the sample time. We use this procedure to measure the SOP fluctuations in a short length of coiled fiber subject to mechanical perturbations.     

Deformation-Strength Relationships in Short-Term Tension of Heat-Resistant Materials

The analysis of 124 curves obtained in short-term tensile tests demonstrate that they can be described by varying strain hardening and softening characteristics. Different stress–strain curves can be produced at invariable yield strength and ultimate strength and interrelated proportional variations of the above characteristics. To determine some specific stress–strain curve, it is necessary to take account of yield strength and ultimate strength as well as strain corresponding to the latter. The relations between yield strength, ultimate strength and hardening and their practically complete absence between these parameters and softening were statistically established.     

Oxidative degradation of polyamide reverse osmosis membranes: Studies of molecular model compounds and selected membranes

Selected aromatic amides were used to model the chemical reactivity of aromatic polyamides found in thin‐film composite reverse osmosis (RO) membranes. Chlorination and possible amide bond cleavage of aromatic amides upon exposure to aqueous chlorine, which can lead to membrane failure, were investigated. Correlations are made of the available chlorine concentration, pH, and exposure time with chemical changes in the model compounds. From the observed reactivity trends, insights are obtained into the mechanism of RO membrane performance loss upon chlorine exposure. Two chemical pathways for degradation are shown, one at constant pH and another that is pH‐history dependent. An alternative strategy is presented for the design of chlorine‐resistant RO membranes, and an initial performance study of RO membranes incorporating this strategy is reported. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1173–1184, 2003     

On the linear correlation between microhardness and mechanical properties in polar polymers and blends

The tensile elastic modulus (E), yield stress (σ_Y) and microhardness (MH) of neat and binary and ternary blends of glassy semicrystalline ethylene–vinyl alcohol copolymer (EVOH), a glassy amorphous polyamide and a semicrystalline nylon‐containing ionomer covering a broad range of properties were examined. The tests were carried out on dry and water‐equilibrated samples to produce stiffer and softer materials, respectively. From the results, more accurate linear correlations were found to describe adequately the microhardness, modulus and yield stress of these strongly self‐associated polymers through hydrogen bonding. Copyright © 2003 Society of Chemical Industry