Influence of ZrB2 hard ceramic reinforcement on mechanical and wear properties of aluminum

In this work, the effect of ZrB₂ (0, 5, 10 and 20?vol%) ceramic reinforcement on densification, structure, and properties of mechanically alloyed Al was investigated. The milling of Al-ZrB₂ powder compositions resulted in formation of agglomerates with varied size. In particular, the size of agglomerates was reduced considerably with increased addition of ZrB₂ to Al. Interestingly, the densification of hot pressed Al increased from 96.06% to 99.22% with ZrB₂ addition. The reduction of agglomerates size was attributed to the enhanced densification of Al-ZrB₂ composites. Pure Al showed relatively low hardness (0.94?GPa) and it was improved to 1.78?GPa with the addition of 20?vol% ZrB₂. The mechanical properties have significantly been improved for Al-ZrB₂ composites. Especially Al - 20?vol% ZrB₂ possessed a very high yield strength (529?MPa), compressive strength (630?MPa) and compressive strain of 19.25%. Realization of such a good combination of mechanical properties is the highest ever reported for Al composites so far in the literature. The coefficient of friction (COF) of Al-ZrB₂ varied narrowly between 0.33 and 0.40 after dry sliding wear against steel disc. The wear rate of Al-ZrB₂ composites was within mild wear regime and varied between 98.88?×?10^?6 and 34.66?×?10^?6 mm³/Nm. Among all the compositions, Al - 20?vol% ZrB₂ composite exhibited the lowest wear rate and high wear rate was noted for pure Al. Mild abrasion, tribo-oxidation, third body wear (wear debris) and delamination were the major material removal mechanisms for Al-ZrB₂ composites. Overall the hardness, strength and wear resistance of Al - 20?vol% ZrB₂ composite was improved by 84.3%, 84.3% and 64.2%, respectively when compared to pure Al.     

Determination of the Quadrupole Splitting in Bulk n-GaAs by Warm-Up Spectroscopy

Semiconductors - We found bulk n-GaAs layers grown by liquid phase epitaxy to be irregularly stressed. Deformation created by this stress causes a small but detectable quadrupole splitting of...     

Calculation of the Ephemeris and Clock Corrections of GLONASS and GPS Navigation Space Vehicles in Ultra-Rapid Regime on the Basis of Measurement Data

Measurement Techniques - An algorithm and program for calculation in ultra-rapid regime of the ephemeris and time information of GLONASS and GPS navigation space vehicles are developed. The results...     

A Dynamic Inertial Weight Strategy in Micro PSO for Swarm Robots

Wireless Personal Communications - A relatively new area of research and development is Swarm Robotics. It is a part of the swarm intelligence field. In the proposed paper, we shall use swarm...     

Investigation into the Influence of Sodium Lignosulfonate,Anionic Surfactants,and Their Mixtures on the Copper Cementation Rate by Zinc

Russian Journal of Non-Ferrous Metals - This article is devoted to the influence of sodium lignosulfonate (SL), anionic surfactants (sodium dodecylsulfate (SDS), sodium dodecylbenzene sulfonate...     

A review on some classes of algebraic systems

ABSTRACT

In this paper, we review some algebraic control system. Precisely, linear and bilinear systems on Euclidean spaces and invariant and linear systems on Lie groups. The fourth classes of systems have a common issue: to any class, there exists an associated subgroup. From this object, we survey the controllability property. Especially, from those coming from our contribution to the theory.     

Fabrication of Wear-Resistant Ti3AlC2/Al3Ti Hybrid Aluminum Composites by Friction Stir Processing

Metallurgical and Materials Transactions A - Hybrid nanocomposites have potential as wear-resistant materials. However, synthesizing these nanocomposites by conventional molten state methods result...     

Design and Optimization of Thick-Walled Cylinders with Load Localization Near the End Face

Strength of Materials - The paper presents a procedure for determining the design parameters of multilayer thick-walled structures with a local load on the inner surface portion located near the...     

Optimization of the Sintering Parameters for Materials Manufactured by Powder Injection Molding

Powder Metallurgy and Metal Ceramics - The properties of sintered and heat-treated steels produced from the Catamold 8740 material by powder injection molding were examined. Parts made of the...