Towards a Better Prediction of Cell Settling on Nanostructure Arrays—Simple Means to Complicated Ends

Vertical arrays of nanostructures (NSs) are emerging as promising platforms for probing and manipulating live mammalian cells. The broad range of applications requires different types of interfaces, but cell settling on NS arrays is not yet fully controlled and understood. Cells are both seen to deform completely into NS arrays and to stay suspended like tiny fakirs, which have hitherto been explained with differences in NS spacing or density. Here, a better understanding of this phenomenon is provided by using a model that takes into account the extreme membrane deformation needed for a cell to settle into a NS array. It is shown that, in addition to the NS density, cell settling depends strongly on the dimensions of the single NS, and that the settling can be predicted for a given NS array geometry. The predictive power of the model is confirmed by experiments and good agreement with cases from the literature. Furthermore, the influence of cell‐related parameters is evaluated theoretically and a generic method of tuning cell settling through surface coating is demonstrated experimentally. These findings allow a more rational design of NS arrays for the numerous exciting biological applications where the mode of cell settling is crucial.     

Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.     

500 kV 开关弹簧机构支架螺栓断裂的原因分析及处理

HPL500B2型弹簧机构支架(BA)螺栓断裂可能导致开关分合闸失败,对其原因进行分析,发现BA螺栓由于预紧固力矩过大,接近其扭断力矩,使得作用在BA螺栓上的力偏高,BA螺栓安全系数仅为12%,安全系数较低。列出BA螺栓更换步骤及注意事项,并详细介绍分闸、合闸弹簧调整步骤,为类似事件的处理提供参考。     

Characteristics of tiger nut milk: effects of milling

A standard method for the extraction of tiger nut milk has been introduced. It has been shown that, although milling duration improves the yield of tiger nut milk solids and its nutrient composition, there is a quantifiable loss of nutrient in the pressing residue during milk extraction. Milling duration improved the colloidal stability of the milk against creaming during 16 h of storage. A higher milling intensity resulted in the aggregation of biological polymers which resulted in colloidal destabilisation. Milling improved the lightness and stability and reduced browning rate of the tiger nut milk during storage. This report is important for the production of tiger nut milk of consistent and comparable characteristics. Milling has been introduced as a processing method for the qualitative and quantitative modulation of the properties of tiger nut milk. It is recommended to develop further strategies to improve the colloidal stability of tiger nut milk as a beverage.     

Behavior of 316L stainless steel containing corrosion pits under cyclic loading

The environmental performance of 316L grade stainless steel, in the form of tensile specimens containing a single corrosion pit with various aspect ratios, under cyclic loading in aerated chloride solutions is investigated in this study. Results from environmental tests were compared and contrasted with those obtained using finite element analysis (FEA). Fractography of the failed specimens obtained from experiments revealed that fatigue crack initiation took place at the base of the shallow pit. The crack initiation shifted towards the shoulder and the mouth of the pit for pits of increasing depth. This process is well predicted by FEA, as the strain contour maps show that strain is the highest around the centric strip of the pit. However, for shallow pits, local strain is uniformly distributed around that strip but begins to concentrate more towards the shoulder and the mouth region for increasingly deep pits.