A biosensor in the time domain based on the diffusion coefficient measurement: intermolecular interaction of an intermediate of photoactive yellow protein

A new type of biosensor is presented for the first time. This method is based on the diffusion measurement in the time domain by the transient grating method. As the first demonstration of this new method, various intermolecular interactions with a reaction intermediate of photoactive yellow protein, such as the protein-protein interaction, protein-DNA interaction, and protein-small molecule binding are detected. The characteristic advantages and limitations are summarized.     

Casting of organic glass by radiation-induced polymerization of glass-forming monomers at low temperature. II. Optical strain of remaining stress type

Previously it was found that casting could be carried out efficiently without strain formation by radiation-induced polymerization of glass-forming monomers. Two types of strain were observed in casting: thermal stream type, which was studied previously, and remained stress type. In this report, the effect of various factors on the formation of remaining stress-type strain in radiation-induced casting polymerization was studied. It was found that the molecular weight of prepolymer did not affect strain formation, while prepolymer concentration and viscosity of the system had a serious influence on strain formation. It could be deduced that this type of strain formed as a result of remaining inner stress due to poor relaxation of the shrinking stress. It was realized that less volume shrinkage of glass-forming monomers accompanying casting polymerization reduced the strain formation of this type in radiation-induced casting polymerization at low temperatures.     

Deposition of chlorophyll-a Langmuir-Blodgett films onto an SnO2 optically transparent electrode

The deposition of chlorophyll-a monolayers onto an SnO₂ optically transparent electrode was studied in relation to the deposition ratio. The values of the deposition ratio, which were approximately 0.95 for the upward movement and very small but non-zero for the downward movement, suggest that the multilayers prepared are Z-type films containing a small fraction of the Y-type component corresponding to the non-zero value. This is consistent with the photo- electrochemical behaviour of the pigmented electrodes which is markedly dependent on the deposition ratios, indicating structural inhomogeneity or imperfection of the multilayers.     

Identification of a model of grinding wheel life by the group method of data handling

A mathematical model for grinding wheel redress life is identified by the polynomial theory of complex systems. Wheel speed, feed, grain size and grade are chosen as the independent variables from among the factors considered to have an effect on wheel wear through the identification of the model. The model obtained enables the redress life to be predicted for all combinations of grinding wheel, work material and grinding conditions, and serves as an aid in the optimization of the grinding process.     

Syntheses,characterizations, and redox behaviors of new self-assembled metal complexes with bridging ligands incorporating chalcogen sites

Three new complexes, [Zn(dbsf)₂(dmf)₂] · 5.5dmf (dbsf = 4,4′-sulfonyldibenzoate) (1β), [Cu(tdsa)(phen)₂] · 1.5EtOH (tdsa = 5,5′-thiodisalicylate, phen = 1,10-phenanthroline) (2), and [Cu(sdp)(phen) · Cu(Hsdp)(phen)(CH₃COO)] · 3EtOH (sdp = 4,4′-sulfonyldiphenolate) (3) were prepared and structurally characterized. Complex 1β shows a one-dimensional coordination framework constructed from bridges between Zn(II) centers with two ligands. Complex 2 is a monomeric complex, which assembles by π–π interactions. Complex 3 shows a unique two-dimensional coordination framework that is constructed from two Cu(II) centers, sdp, and Hsdp. The redox properties of these three complexes were characterized by solid-state cyclic voltammetry. Complexes 1β and 3 show irreversible reduction waves because of the reduction of their sulfone sites. Complex 2 shows an irreversible oxidation wave because of oxidation of the sulfide site.     

Mechanochemical decomposition of PVC by using La2O3 as additive

A polyvinyl chloride (PVC, [CH2CHCl]n) sample was ground with one of the following oxide samples, lanthanum oxide (La2O3) and calcium oxide (CaO), as a reference, to investigate its mechanochemical (MC) decomposition. According to the XRD patterns for the ground products, peaks of lanthanum oxy-chloride, LaOCl which is water insoluble, were observed to appear in the patterns of the mixture samples at a molar ratio of (PVC: La2O3 = 1:2) and (1:4), after 20 min grinding, while the patterns of the ground PVC-CaO mixtures show the formation of CaOHCl, which is water soluble, in the products after 2 h grinding. TG patterns taken for the PVC-La2O3 mixtures ground for different periods of time do not indicate significant weight loss in the range from 200 to 300 degrees C, and this suggests that La2O3 is more effective additive than CaO in the MC decomposition for PVC. FT-IR patterns for organic phases in the ground mixture show the reduction of CCl bindings in the PVC structure. The MC reaction between PVC and La2O3 is accompanied by the formation of C-O single bonds, to form LaOCl, which is insoluble in water at ambient condition. This is the reason why the yield of Cl extracted by the water leaching reaches only less than 50%, while it reaches almost 100% in the yield of Cl from the PVC-CaO mixture ground for 2 h or more.     

Prediction of cutting forces and machining error in ball end milling of curved surfaces -II experimental verification

This paper presents the results of a series of experiments performed to examine the validity of a theoretical model for evaluation of cutting forces and machining error in ball end milling of curved surfaces. The experiments are carried out at various cutting conditions, for both contouring and ramping of convex and concave surfaces. A high precision machining center is used in the cutting tests. In contouring, the machining error is measured with an electric micrometer, while in ramping it is measured on a 3-coordinate measuring machine. The results show that in contouring, the cutting force component that influences the machining error decreases with an increase in milling position angle, while in ramping, the two force components that influence the machining error are hardly affected by the milling position angle. Moreover, in contouring, high machining accuracy is achieved in “Up cross-feed, Up cut” and “Down cross-feed, Down cut” modes, while in ramping, high machining accuracy is achieved in “Left cross-feed, Downward cut” and “Right cross-feed, Upward cut” modes. The theoretical and experimental results show reasonably good agreement.     

Pervaporation of methanol–water mixture by poly(γ-methyl L-glutamate) membrane and synergetic effect of their mixture on diffusion rate

The pervaporation behaviors of methanol–water by poly(γ-methyl L -glutamate) (PMLG) membrane at non-steady- and steady-state permeation were investigated. The values of t_1/2 (time required to reach a half value of steady-state permeation flux) for methanol and water changed and did not change with the component in feed, respectively. Both of the average diffusion coefficients for methanol–and water–PMLG from the mixture changed exponentially with the sorption amount of methanol by the synergetic effect on diffusion. The difference in behavior of non-steady and steady state diffusion was explained by whether D_o (diffusion coefficient at zero penetrant concentration) was influenced by the concentration distribution of penetrant in PMLG membrane.