The elliptic paraboloid failure criterion for cellular solids and brittle foams

Summary Cellular solids and brittle foams are increasingly finding application in constructions mainly as core materials for loaded sandwich structures where the loading of the structure generates multiaxial stress states on them. It has been established that the principal mechanism of deformation is based on the cell-wall bending and closed-cell as well as open-cell foams present similar stiffnesses. Therefore simple relations are found for their tensile, compressive and shear strengths and their elastic properties.It has been established in this paper that the modes of failure of such materials can be satisfactorily described by the elliptic paraboloid failure criterion for the general orthotropic body. Then, as soon as the yield or failure stresses in simple tension and compression are measured along the three principal stress directions of the material the failure locus is unequivocally defined and all the properties of the material under any complicated load can be accurately established. However, since these materials fail in the compression-compression-compression octant of the principal stress space by elastic buckling, the EPFS-criterion is cut-off by an ellipsoid surface, with intercepts along the principal axes the respective compressive failure stresses.The criterion thus established yields satisfactory results. It has been tested among others in a reticulated vitreous carbon foam as well as in an aluminium foam. The experimental results for these foams existing in the literature are fitting better with this universal criterion than any other considered, thus indicating the validity of the elliptic paraboloid failure criterion also for this type of materials.     

Thermal analysis of the architecture of old and new houses at Ghadames

The study suggests improvements in the design of new houses to conserve energy and enhance indoor thermal comfort. Summer temperature records show that a new house has an average indoor temperature of 35°C with the ambient average 31°C. The traditional house in the old city recorded 28°C for the same period. Winter temperatures in both types of houses were similar (12°C) when not occupied. Architectural features of the two houses were compared to identify those responsible for difference in the thermal performance. Larger exposed surface and window areas, higher overall heat transfer coefficient and weaker thermal coupling with the ground for the new houses seems to contribute to their inferior thermal performance.     

The glass fibre-polymer interface: II—Work of fracture and shear stresses

Pull-out experiments have been carried out on single production fibres under carefully controlled conditions. Four parameters were determined. The interfacial yield stresses, of about 9–14 MPa, were very much smaller than the shear strengths of the bulk polymers in the case of an epoxy, whether post-cured or not, and a non-post-cured polyester. Values for the work of fracture of the interface varied from 140 to 300 Jm^?2, and again were less than those of the polymer. Interface failure sometimes took place in the epoxy rather than at the fibre surface, whereas with the polyester it always took place at the fibre surface. After interface failure, pull-out was governed by friction, with maximum shear stresses of 7–10 MPa for polyester, and 21–34 MPa for epoxy, the higher values being obtained for the post-cured resins. Average frictional shear stresses were sometimes less than a half of the maximum shear stress, indicating that the fibre Poisson's shrinkage was playing an important role in the pull-out process. A silicone release agent reduced the frictional shear stresses to 2·5 MPa, with both resins.     

FMR and EXAFS modeling of heat-treated Fe-rich and Co-rich TM-M thin films

Ion-beam sputter-deposited alloy films of Co/sub 74/Fe/sub 6/B/sub 15/Si/sub 5/ and Fe/sub 75/Ni/sub 5/B/sub 15/Si/sub 5/ were examined for their magnetic and structural properties. Films were characterized by ferromagnetic resonance, vibrating sample magnetometry, and extended X-ray absorption fine structure (EXAFS) analysis. Using atomic parameters deduced from EXAFS modeling and fitting procedures, magnetic properties were calculated with no adjustable parameters. Correlation between perpendicular FMR measurements and EXAFS first-shell modeling suggests a low-temperature formation of cobalt-borides in the Co/sub 74/Fe/sub 6/B/sub 15/Si/sub 5/ alloy. Annealed Fe/sub 75/Ni/sub 5/B/sub 15/Si/sub 5/ samples did not display evidence of structural and/or magnetic instabilities until the onset of long-range crystallization near T/sub ann/=400 degrees C.<>     

Calculation of the molar volume of liquid hydrocarbons

Equations are proposed for calculating the molar volume of liquid hydrocarbons used in production of surfactants. With such data, it will be possible to calculate most of the physicochemical properties of these hydrocarbons to solve many process problems. __________ Translated from Khimiya i Tekhnologiya Topliv i Masel, No. 6, pp. 39–41, Novemmber–December, 2006.