Orientation of smoke production in polyacrylonitrile

The introduction of ionic additives, such as KCN, or acidic comonomer units, such as methacrylic acid, which change the nature of the mechanism of nitrile oligomerization reaction from radical to ionic and cause its initiation at lower temperature, allows the level of obscurity and the total amount of smoke production, both in smouldering and flaming conditions to be decreased. An opposite result is obtained if diphenylpicrylhydrayl (DPPH) radicals in polyacrylonitrile is introduced; DPPH retards the initiation of the radical nitrile oligomerization reaction. The acrylonitrile-methacrylic acid copolymers have a limiting oxygen index, which increases with the methacrylic acid content. Owing to the increased amount of NH₃ produced during pyrolysis, the copolymers have a swelling behavior during the combustion test.     

Coagulation dynamics of fractal flocs induced by enmeshment and electrostatic patch mechanisms

The size and structure of flocs during floc formation were monitored for various coagulation mechanisms. Two distinctive mechanisms, namely, enmeshment and electrostatic patch, govern the dynamics of kaolin particles coagulation by polyaluminum chloride (PACl). They were investigated by small angle static light scattering (SASLS) and solid-state ²⁷Al NMR. In addition, a novel wet SEM (WSEM) was used in-situ to image the morphology of the aggregate in aqueous solution. Synthetic suspended particles were coagulated by two PACl products, a commercial product (PACl) and one laboratory product (PACl-E). The PACl-E contained more than 60% Al₁₃ while the PACl contained only 7% Al₁₃, with large percentage of colloidal Al. For coagulation by PACl at neutral pH and high dosage where the strong repulsion between particles occurs, the enmeshment ruled by reaction-limited aggregation (RLA) results in larger sweep flocs as well as higher fractal dimensional structure. For coagulation by PACl-E at alkaline pH and low dosage, the flocs were coagulated predominately by electrostatic patch with Al₁₃ aggregates. At such condition, it is likely that diffusion-limited aggregation (DLA) predominately rule PACl-E coagulation. The fractal dimension (D_s) values of PACl and PACl-E flocs formed at enmeshment and electrostatic patch increased with dosage, respectively. When breakage of flocs occurs, the breakage rate of PACl-E flocs is slower than that of sweep flocs. By WSEM imaging, the adsorption of spherical Al precipitates onto the particles was observed to form sweep flocs with a rough and ragged contour, while the PACl-E flocs were formed with a smooth and glossy structure.     

A large-scalein situ permeability test at Presenzano (Italy)

Bulletin of Engineering Geology and the Environment - Soil permeability had to be carefully determined in order to decide whether or not the whole lower reservior (750.000 m2) of the Presenzano...     

Free vibration of a clamped-free circular cylindrical shell partially filled with liquid—Part I: Theoretical analysis

Theoretical analyses are presented for the linear free vibration of a clamped-free cylindrical shell partially filled with an incompressible, inviscid liquid. For the vibration of the shell itself, the dynamic version of the Donnell equations was used and the problem was solved with the modified Galerkin procedure, taking the effect of the axisymmetric deformation due to the static liquid pressure into consideration. Concerning the vibration relevant to the liquid motion, the solution for the velocity potential was assumed as a sum of two sets of linear combinations of the suitable harmonic function, the unknown parameters of which were imposed to satisfy both boundary conditions along the wetted shell wall and the free liquid surface in a sense of appropriate series expansions. The procedure stated in the foregoing leads to a determinantal equation for the determination of the natural frequencies of the present shell-liquid system. To compare with the experimental results which will be stated in a companion paper,¹⁴ detailed numerical results will be presented in another companion paper¹³ on the free vibration characteristics of the two test cylinders partially filled with water.     

A semiautomated procedure for the determination of phosphorus in water, waste waters and particulates

Improved procedures for the determination of total dissolved phosphorus (TDP), particulate phosphorus (PP) and dissolved inorganic orthophosphate (DP) are described. Organic particulate material is solubilized in 5 n NaOH, and phosphorus compounds are oxidized and mineralized to orthophosphate by persulfate digestion. DP is determined by an improved automated molybdenum blue procedure that does not require sample pH adjustment or a correction for silicate interference in the 0–50 mg Si 1^?1 range. The use of 36-position digestion racks allows 32 TDP or PP samples to be digested in ca. 1 and 4 h respectively. Detection limits in μg of phosphorus 1^?1 are DP, 2; TDP, 5; and PP. 1. Waste water samples were analyzed for TDP and PP by the nitric acid-sulfuric acid procedure and by the proposed method. There was no significant difference between the two sets of data (P > 0.45).     

Levels of copper in the urine of women from nonpolluted farming regions of Japan.

Nearly 1500 spot urine samples were collected in the winter of 1987-1988 from women of seven farming prefectures located throughout Japan. Samples were analyzed for copper by flameless atomic absorption spectrometry. The copper content of the urine samples (Cu-U) distributed log-normally with a geometric mean (geometric standard deviation) of 36.9 (1.47) micrograms/l after adjustment for the specific gravity of urine of 1.016. The 95% confidence range was 17.1-79.7 micrograms/l. Neither alcohol consumption nor smoking habit affected the Cu-U. A literature survey showed that the observed level appears to be somewhat higher than previously reported values.     

Interaction effects of multiple pool fires

What are the effects of flame behavior of a number of fires burning in close proximity to one another? The results of measurements of burning rates, heat feedback, flame height, and flame trailing are reported for fires involving liquid pools.     

Studies on oxidation of benzo [a] pyrene by sunlight and ozone

The destruction of the carcinogen benzo[a]pyrene (BaP) by light is well known; laboratory workers are routinely advised to cover fluorescent lamps with yellow filters while treating samples containing BaP. However until recently the mechanism of oxidation by sunlight and ozone had not been studied in detail. Concentrations of benzo[a]pyrene in urban air are in the range of 5–10 μg/1000 m³. Oxidant concentrations (predominantly in the form of ozone) are reported to be in the range of 0.01 ppm (22 μg per m³). Thus a sampling system with a filter paper would filter about 22,000 μg of ozone passing through and collect about 5 μg of BaP for analysis. The effect of interactions of such large ozone concentrations with BaP deposited on the filter paper is reported; data for the oxidation rates for benzo[a]pyrene coated on quartz surface and exposed to ozone or sunlight are presented. The oxidation products were analysed by thin-layer chromatography and highpressure liquid chromatography. From about eight products detected in these experiments, three have been identified as quinones based on UV-absorption spectrometry and mass spectrometry. Oxidation rates as high as 100% per hour of exposure are observed when less than 0.1 μg of BaP is coated inside the quartz tubes and exposed to ozone or sunlight. Oxidation rates for benzo[a]pyrene (using tritiated BaP) were determined for two types of experimental conditions. In the first set, tritiated BaP was spotted onto a glass fibre paper and sampling continued for 24 h; the loss of BaP was found to be 88%. In the second set tritiated BaP was spotted at intervals of one hour, for eight hours, while sampling is being carried out and the loss of BaP during the period was estimated to be 50%.     

The impact of using chilled water storage systems on the performance of air cooled chillers in Kuwait

In the air conditioning (AC) industry chilled water storage (CWS) systems are one form of cool thermal storage technology that can be used to time shift the electrical load of the system from the peak day periods to off peak night time periods. In this paper the data for the actual exported and generated electrical energy obtained for the power stations in Kuwait has been used to estimate the electrical energy consumption and the peak electrical load of AC systems. Since the chiller in an air cooled AC system represent more than 75% of the total electrical power consumed by an AC system during the peak demand period, the impact of using CWS systems with alternative operating strategies including partial (load levelling), partial (demand limiting) and full load has been investigated. In our conclusions we estimate that approximately 45% of the total annual exported electrical energy is consumed solely by AC systems as a result of the very high ambient temperatures occurring between March and October. Furthermore, it is estimated AC systems represent about 62% of the peak electrical load. The results demonstrate that CWS can reduce the peak electrical load of a chiller in an air cooled AC system by up to 100% and reduce the nominal chiller size by up to 33% depending upon the operating strategy adopted. This is achieved with only a 4% increase in power consumption of the chiller for all CWS strategies except for full storage where the energy consumption actually decreases by approximately 4%.     

A digital wind gust recorder

The instrument was a byproduct of an undergraduate final year project on wind power which was carried out by the Department of Mechanical Engineering of the University of Liverpool.The windmill test site was on an exposed, rocky island where there was no history of weather recording but a long tradition of violent winds.Field experience during the winter months suggested that corrosion fatigue arising from wind buffeting and salt spray would rank equally with maximum wind pressure as criteria of failure and if modern materials, so convenient for forming aerodynamic surfaces, were to be used then limited life concepts would need to be considered. This called for more knowledge of wind variations at the test site. A complete wind spectrum taken on chart recording instruments would have been ideal but since such such refined devices were not available the instrument to be described was designed.The only wind measuring instrument which was available was a rotating cup anemometer. This supplied an alternating voltage proportional to its rotational speed. It also operated a gear driven microswitch which could give an integrated “miles of wind” reading on an electromagnetic counter.Briefly the e.m.f. generated by the anemometer (Fig. 1) was matched against a pre-set voltage corresponding to the required gust velocity. When this was exceeded an appropriate counter was operated. Only the rising e.m.f. was significant. The subsequent fall was ignored. Initially three stages were incorporated which reported the gusts rising through forty, fifty and sixty knots, respectively. These recorded on separate counters. All basic settings were based on pitot-static speed determinations in a wind tunnel.