Valorisation of waste fractions from autohydrolysis of selected lignocellulosic materials

Non‐isothermal processing of lignocellulosic materials in aqueous media (autohydrolysis reaction) under mild conditions leads to solutions containing valuable chemicals (oligosaccharides, sugars and acetic acid) and other, undesired, compounds (belonging to the extractive and acid‐soluble lignin fractions) which have to be removed in further purification treatments. Liquors obtained by non‐isothermal autohydrolysis of Eucalyptus globulus wood and corncobs under a variety of operational conditions were extracted with ethyl acetate in order to remove non‐saccharide components, and the suitability of the fraction dissolved in the organic phase was assayed for possible utilisation as an antioxidant. The yield and antioxidant activity of ethyl acetate extracts (measured by the α,α‐diphenyl‐β‐picrylhydrazyl (DPPH) radical scavenging capacity) showed a strong dependence on the autohydrolysis conditions. The antioxidant activity of extracts obtained under selected operational conditions compared well with synthetic antioxidants. © 2003 Society of Chemical Industry     

X-ray or UV adjustment of MOS threshold voltage: Analytical and numerical modeling

A model is formulated that describes how radiation-induced charge accumulates in the gate oxide of a MOS structure and how it decays through tunneling and thermal emission. The model is used in a numerical analysis of the x-ray or UV adjustment of threshold voltage in MOS-circuit manufacture. The limits of this process technique are evaluated.     

Using the magneto-optical Kerr effect to study magnetization processes in two-dimensional magnonic crystals based on YIG thin films

The magneto-optical Kerr effect for red (628 nm) and green (532 nm) light is used to study magnetization processes in 2D magnonic crystals obtained by etching pits with the diameter D ≈ 32 μm to a depth of t ≤ 2 μm in a 16.1-μm-thick film of yttrium iron garnet (YIG). Hysteresis loops obtained in the case of the inplane crystal magnetization at 628 nm are characterized by lower saturation fields H _s and higher remanent magnetizations than those obtained at 532 nm, a result that is attributed to different absorption coefficients of the YIG film at these wavelengths. This difference between the magnetization curves reflects the fact that the magnonic-crystal surface probed with the green light makes a greater contribution to the magneto-optical Kerr effect. Therefore, the green light is more sensitive to the demagnetizing fields, which govern magnetization processes in the magnonic crystals.     

Second harmonic generation from a ferroelectric film

We derive an expression for transmittivity (T_SHG) of second harmonic generation (SHG) signals from a ferroelectric (FE) film. Intensities of up and down fields in the medium are investigated in relation to T_SHG. The derivations are made based on undepletion of input fields and nonlinear wave equation derived from the Maxwell equations. We present two cases: film without mirrors and with partial mirrors. Expressions for the newly derived nonlinear susceptibility coefficients of SHG for real crystal symmetry [J. Opt. Soc. Am. B 19 (2002) 2007] are used to get more realistic results. Variations in T_SHG with respect to film thickness are illustrated.     

1/f noise in large-area Hg<Subscript>1−x</Subscript>Cd<Subscript>x</Subscript>Te photodiodes

The 1/f noise in photovoltaic (PV) molecular-beam epitaxy (MBE)-grown Hg_1−xCd_xTe double-layer planar heterostructure (DLPH) large-area detectors is a critical noise component with the potential to limit sensitivity of the cross-track infrared sounder (CrIS) instrument. Therefore, an understanding of the origins and mechanisms of noise currents in these PV detectors is of great importance. Excess low-frequency noise has been measured on a number of 1000-μm-diameter active-area detectors of varying “quality” (i.e., having a wide range of I-V characteristics at 78 K). The 1/f noise was measured as a function of cut-off wavelength under illuminated conditions. For short-wave infrared (SWIR) detectors at 98 K, minimal 1/f noise was measured when the total current was dominated by diffusion with white noise spectral density in the mid-10⁻¹⁵A/Hz^1/2 range. For SWIR detectors dominated by other than diffusion current, the ratio, α, of the noise current in unit bandwidth i_n(f = 1 Hz, V_d = −60 mV, and Δf = 1 Hz) to dark current I_d(V_d = −60 mV) was α_SW-d = i_n/I_d ∼ 1 × 10⁻³. The SWIR detectors measured at 0 mV under illuminated conditions had median α_SW-P = i_n/I_ph ∼ 7 × 10⁻⁶. For mid-wave infrared (MWIR) detectors, α_MW-d = i_n/I_d ∼ 2 × 10⁻⁴, due to tunneling current contributions to the 1/f noise. Measurements on forty-nine 1000-μm-diameter MWIR detectors under illuminated conditions at 98 K and −60 mV bias resulted in α_MW-P = i_n/I_ph = 4.16 ± 1.69 × 10⁻⁶. A significant point to note is that the photo-induced noise spectra are nearly identical at 0 mV and 100 mV reverse bias, with a noise-current-to-photocurrent ratio, α_MW-P, in the mid 10⁻⁶ range. For long-wave infrared (LWIR) detectors measured at 78 K, the ratio, α_LW-d = i_n/I_d ∼ 6 × 10⁻⁶, for the best performers. The majority of the LWIR detectors exhibited α_LW-d on the order of 2 × 10⁻⁵. The photo-induced 1/f noise had α_LW-P = i_n/I_ph ∼ 5 × 10⁻⁶. The value of the noise-current-to-dark-current ratio, α appears to increase with increasing bandgap. It is not clear if this is due to different current mechanisms impacting 1/f noise performance. Measurements on detectors of different bandgaps are needed at temperatures where diffusion current is the dominant current. Excess low-frequency noise measurements made as a function of detector reverse bias indicate 1/f noise may result primarily from the dominant current mechanism at each particular bias. The 1/f noise was not a direct function of the applied bias.     

Effect of Sb implantation on copper silicides formation and morphology after annealing of Cu/Si structures

In this work, the solid state reaction between a thin film of copper and silicon has been studied using Rutherford backscattering spectroscopy, X-ray diffraction, scanning electron microscopy and microprobe analysis. Cu films of 400 and 900 Å thicknesses are thermally evaporated on Si(1 1 1) substrates, part of them had previously been implanted with antimony ions of 5×10¹⁴ or 5×10¹⁵ at. cm⁻² doses. The samples are heat-treated in vacuum at temperatures in the range 200–700 °C for various times. The results show the growth and formation of Cu₃Si and Cu₄Si silicides under crystallites shape dispatched on the sample surface, independently of the implantation dose. On the other hand, it is established that the copper layer is less and less consumed as the antimony dose increases, resulting in the accumulation of Sb⁺ ions at silicide/Si interface and in the silicide layer close to surface. The exposure of samples to air at room temperature shows the stability of Cu₄Si phase whereas the Cu₃Si silicide disappears to the benefit of the silicon dioxide formation. The observed phenomena are discussed.     

Training and optimization of an artificial neural network controlling a hybrid power filter

A hybrid power compensator (HPC) consisting of a static VAr compensator and a dynamic compensator needs to be optimally controlled during the compensation of nonlinear loads. The HPC must be controlled to meet minimum requirements in terms of power factor and harmonic distortion, while at the same time minimizing its total cost. An artificial neural network (ANN) is used to control the HPC amidst a very dynamic power system environment. The performance of a reference ANN is evaluated while controlling an HPC connected to a typical nonlinear industrial load. The training and performance of the ANN is then optimized in terms of training set size, training set packing and ANN topology and the performance compared to the reference ANN. This paper highlights the importance of optimising the mentioned ANN parameters to achieve optimum ANN training and modeling accuracy. The results obtained reveals that the application of an ANN in controlling an HPC is feasible given that the ANN parameters are chosen appropriately.     

Synthesis of ZSM‐5 Films and Monoliths with Bimodal Micro/Mesoscopic Structures

A route to synthesize ZSM‐5 crystals with a bimodal micro/mesoscopic pore system has been developed in this study; the successful incorporation of the mesopores within the ZSM‐5 structure was performed using tetrapropylammonium hydroxide (TPAOH)‐impregnated mesoporous materials containing carbon nanotubes in the pores, which were encapsulated in the ZSM‐5 crystals during a solid rearrangement process within the framework. Such mesoporous ZSM‐5 zeolites can be readily obtained as powders, thin films, or monoliths.     

Optimal pilot waveform assisted modulation for ultrawideband communications

Ultrawideband (UWB) transmissions induce pronounced frequency-selective fading effects in their multipath propagation. Multipath diversity gains can be collected to enhance performance, provided that the underlying channel can be estimated at the receiver. To this end, we develop a novel pilot waveform assisted modulation (PWAM) scheme that is tailored for UWB communications. We select our PWAM parameters by jointly optimizing channel estimation performance and information rate. The resulting transmitter design maximizes the average capacity, which is shown to be equivalent to minimizing the mean-square channel estimation error, and thereby achieves the Crame/spl acute/r-Rao lower bound. Application of PWAM to practical UWB systems is promising because it entails simple integrate-and-dump operations at the frame rate. Equally important, it offers a flexible UWB channel estimator, capable of striking desirable rate-performance tradeoffs depending on the channel coherence time.     

Effect of the Distribution of Manganese Ions on the Properties of Mn-Doped (Ba,Y)TiO3 PTCR Ceramics

The electrical properties and microstructure of (Ba,Y)TiO₃ PTCR ceramics were studied. The results indicate that the Mn ions increase the intergranular barrier height and produce a high-resistance layer on the grain surface. The temperature-dependent resistances of the grain bulk, surface layer, and grain boundaries, the temperature coefficient of resistance, and the magnitude of the varistor effect were assessed as a function of Mn content.