Electroconductive nylon 6 and copper composites

A study is reported on the effect of the filler size and concentration on the electrical resistivity, density, and hardness of composites made of copper powder embedded in nylon 6 matrix by means of compression molding. The electrical resistivity of the composites is > 10¹¹ ohm·cm unless the metal content reached the percolation threshold, beyond which the resistivity decreased markedly by as much as 10¹². The percolation concentration was found to decrease with a decrease in the average particle diameter. The density of the composites was measured and compared with values calculated assuming different void levels within the samples. However, there is no sharp variation in the density due to the onset of percolation. Furthermore, it is shown that a percolation concentration can be also defined in the hardness/metal concentration curves as the intercept of linear regression curves of the low and high metal content regimes, respectively.     

Comparison of a contactor catalytic membrane reactor with a conventional reactor: example of wet air oxidation

A wet air oxidation reaction was carried out in a gas/liquid catalytic membrane reactor of the contactor type. The oxidation of formic acid was used as a model reaction. The mesoporous top-layer of a ceramic tubular membrane was used as catalyst (Pt) support, and was placed at the interface of the gas (air) and liquid (HCOOH solution) phases.

A similar reaction was carried out in a conventional batch reactor, using a steering rate high enough to avoid gas-diffusion limitations, and exactly identical conditions than for the CMR (amount of catalyst, pressure, etc.). At room temperature, the CMR showed an initial activity three to six times higher than the conventional reactor. This activity increase was attributed to an easier oxygen access to the catalytic sites. Nevertheless, the catalytic membrane gradually deactivated after a few hours of operation. Different deactivation mechanisms are presented.     

Surface Modification of Polydimethylsiloxane via Combined Aminolysis and Alcoholysis Generating Cell Adhesive and Antifouling Properties

Polydimethylsiloxane (PDMS) is an elastomeric polymer frequently used as implant material, for flexible tubing and in microfluidic devices. The pronounced hydrophobic surface of this unique material impedes many applications where a good wetting behavior is required. Consequentially, various ways of surface modifications have been used to introduce new properties. Plasma treatment is the most popular technique in this respect, but is not generally applicable, especially if hardly accessible surfaces are to be modified. A novel wet-chemistry-based modification scheme yielding an amino-functionalized PDMS surface using a combined alcoholysis/aminolysis reaction is presented. Biological applications are exemplified by the conjugation of the RGD peptide, or polyethylene glycol (PEG) and heparin, yielding surfaces with cell-adhesive or nonthrombogenic properties, respectively. The effect of subsequent conjugation with an adhesive peptide is tested in cell culture. Additionally, two antifouling surfaces generated by coupling heparin and polyethylene glycol respectively are shown to improve the materials resistance to platelet adhesion drastically while simultaneously preventing hydrophobic recovery of the PDMS surface. The findings provide a versatile means of surface functionalization of PDMS substrates and is suitable for many biomedical applications.     

Experimental Study on Electrostatically Enhanced Granular Filters

Filtration of charged aerosols by granular bed filters enhanced by an externally applied electrostatic field was studied experimentally. The filtration efficiencies of latex aerosols by sand beds were measured for various aerosol and bed granule diameters. The results were compared with theoretical solutions. It was demonstrated that high filtration efficiencies of charged aerosols may be achieved when moderate electrostatic fields are applied to a filter.     

Influence of shear flow on the preparation of polymer layered silicate nanocomposites

In this paper the influence of melt-processing on the final polymer/layered silicate nanocomposite morphology is discussed. In particular the role of shear forces on the transformation of the original large clay agglomerates is of interest. Several polymer nanocomposites were prepared by melt-extrusion, involving polycaprolactone, poly(ethylene oxide), polyamide-12 or polyamide-6 as the matrix polymer. The nanocomposite morphology was characterised by X-ray diffraction and transmission electron microscopy and the clay tactoid morphology with polarised optical microscopy and scanning electron microscopy. The development of the tactoid and nanocomposite morphology during melt-mixing under shear was studied time-resolved by optical microscopy in conjunction with a rheometer and synchrotron X-ray scattering together with a Couette type flow cell. The shear forces in the melt-preparation of polymer layered mineral nanocomposites facilitate the break-up of large-sized agglomerates, whereas the extent of further exfoliation of the mineral layers is determined by the compatibility between the polymer matrix and the mineral layers rather than by shear forces.     

Targeting optimum resource allocation using reverse problem formulations and property clustering techniques

Decoupling the constitutive equations from the balance and constraint equations allows for reformulating a conventional forward problem into two reverse problems. The first reverse problem is the reverse of a simulation problem, where the process model is solved in terms of the constitutive (synthesis/design) variables instead of the process variables, thus providing the synthesis/design targets. The second reverse problem (reverse property prediction) solves the constitutive equations to identify unit operations, operating conditions and/or products by matching the synthesis/design targets. Visualization of the problem is achieved by employing recently developed property clustering techniques, which allows a high-dimensional problem to be visualized in two or three dimensions. The clusters by definition satisfy intra-stream and inter-stream conservation through linear “mixing” rules, which allows for the development of consistent additive rules along with their ternary representation.     

Preparation of carbon-based adsorbents from sewage sludge pyrolysis to remove metals from water

The objective of this study was to evaluate the use of cheap carbon-based adsorbents from sewage sludge pyrolysis to remove Na⁺, K⁺, Ca²⁺ and Mg²⁺ from saline water. Four model solutions of NaCl, KCl, CaCl₂ and MgCl₂ that simulated seawater composition were used. The model solutions were 456.54 mmol_c L⁻¹ NaCl, 9.72 mmol_c L⁻¹ KCl, 19.96 mmol_c L⁻¹ CaCl₂ and 111.09 mmol_c L⁻¹ MgCl₂. Two carbon adsorbents, one with chemical activation, were prepared by a new method and evaluated for ion adsorption. The results indicated that carbon adsorbent without chemical activation was the most effective in removing ions from different solutions and the removal of metals followed the sequence: Na⁺ (76.78−69.66) >K⁺ (66.0−57.80) >Mg²⁺ (44.84−42.85) >Ca²⁺ (35.12−12.38). Results showed that it is to possible prepare carbon-based adsorbents from sewage sludge following inexpensive and environmentally acceptable methods.     

The Importance of Small Extracellular Vesicles in the Cerebral Metastatic Process

Brain metastases represent more than 50% of all cerebral tumors encountered in clinical practice. Recently, there has been increased interest in the study of extracellular vesicles, and the knowledge about exosomes is constantly expanding. Exosomes are drivers for organotropic metastatic spread, playing important roles in the brain metastatic process by increasing the permeability of the blood–brain barrier and preparing the premetastatic niche. The promising results of the latest experimental studies raise the possibility of one day using exosomes for liquid biopsies or as drug carriers, contributing to early diagnosis and improving the efficacy of chemotherapy in patients with brain metastases. In this review, we attempted to summarize the latest knowledge about the role of exosomes in the brain metastatic process and future research directions for the use of exosomes in patients suffering from brain metastatic disease.     

Production of Methyl Oleate in Reactive‐Separation Systems

The esterification of oleic acid and methanol using sulfuric acid as a homogeneous catalyst is studied in reactive‐separation systems. The conversion of the free fatty acid was investigated in two different experiments with the molar ratio of methanol/oleic acid, amount of catalyst, temperature, and reaction time as variables. The conversion of the free fatty acid was found to depend strongly on the molar ratio of methanol/oleic acid. The reaction time had a direct effect on the conversion of the free fatty acid, and this conversion decreased with higher temperature. These results were valuable for a preliminary study on biodiesel production, using an acid homogeneous catalyst in a reactive dividing‐wall distillation column.