Synthesis and electrochemical studies of the 4 V cathode, Li(Ni2/3Mn1/3)O2

Layered Li(Ni_2/3Mn_1/3)O₂ compounds are prepared by freeze-drying, mixed carbonate and molten salt methods at high temperature. The phases are characterized by X-ray diffraction, Rietveld refinement, and other methods. Electrochemical properties are studied versus Li-metal by charge–discharge cycling and cyclic voltammetry (CV). The compound prepared by the carbonate route shows a stable capacity of 145 (±3) mAh g⁻¹ up to 100 cycles in the range 2.5–4.3 V at 22 mA g⁻¹. In the range 2.5–4.4 V at 22 mA g⁻¹, the compound prepared by molten salt method has a stable capacity of 135 (±3) mAh g⁻¹ up to 50 cycles and retains 96% of this value after 100 cycles. Capacity-fading is observed in all the compounds when cycled in the range 2.5–4.5 V. All the compounds display a clear redox process at 3.65–4.0 V that corresponds to the Ni^2+/3+–Ni^3+/4+ couple.     

Solar cookers—part-II—cooking vessel with central annular cavity

Cooking vessels used in a solar cooker must be able to transfer the heat trapped in the cooker effectively to the food material. In the preceding paper (Part-I) the advantage of keeping the vessel on lugs was discussed. In the current paper the performance of a cooking vessel with a central annular cavity kept on lugs is discussed. The experiments were conducted for several days using water and thermic fluid as working medium. The studies indicated that the cooking vessel with central annular cavity on lugs performs much better than the conventional vessel kept on the floor of the cooker. The conventional vessel is considered to be the benchmark for the purposes of comparison.     

Flux pattern and fouling of membranes during ultrafiltration of some dairy products

The flux pattern of milk (whole milk, skimmed milk and buttermilk) showed a distinct contrast to whey (sweet whey and acid casein whey) systems during ultrafiltration (UF) at constant composition. For milk systems, the initial flux was lower than for whey systems, but the flux stabilised within a few minutes of operation. However, for both acid and sweet whey, the flux continued to fall with time for nearly 1 h. The fouling coefficient (FC) for buttermilk was 0.6 after 5 min, rising to 0.68 after 60 min. During this time flux did not decline, suggesting that concentration polarisation (CP), rather than fouling, was controlling the flux rate. In contrast, the FC for whey was 0.5 after 5 min with a progressive rise over the next 55 min, but the flux also fell throughout this period suggesting that flux was controlled by fouling rather than CP. The higher concentration of protein in milk systems appeared to be responsible for CP, rather than fouling, being the controlling mechanism.     

Way-Point Multicast Routing Framework for improving QoS in hybrid wireless mesh networks

Since internet access is used by billions of people worldwide and the number of internet user is also increasing every day, a new technology called as wireless mesh network (WMN) is becoming popular. This is because it has some desirable characteristic, but it has some limitation for multi-hop routing, bandwidth, and many more. In order to overcome these issues, we proposed Way-Point Multicast Routing Framework (WPMRF) for improving the quality of service (QoS) in Hybrid WMN. Initially, the multicast framework is established based on the minimum load factor. The route established with least load factor is considered, as it avoids any kind of congestion in the network. After that, segmentation of route is done, and the way-point nodes are selected to join the multicast session. After that, the transmission is performed using MAODV and ODMRP protocol. In addition, an estimated route disconnection parameter is used for fast route recovery process and helps to select more reliable route path. The advantage of the proposed work is that it provides more reliable routing path to increase the quality of service (QoS) with fast route recovery process.     

Optimization of on-chip ESD protection structures for minimal parasitic capacitance

Diodes are key components in on-chip electrostatic discharge (ESD) protection design. As the operating frequency of the microchip being protected against the ESD continues to increase, the parasitic capacitance associated with the diodes in the ESD structure starts to impose problems for RF operation. This paper presents a systematic approach to optimize the diode structure for minimal parasitic capacitance based on the requirements of breakdown voltage and heat dissipation. Device simulator Atlas with mix-mode simulation capability is calibrated against measurement data and used to carry out the optimization. An optimized diode structure with a parasitic capacitance of less than 30 fF at an operating frequency of 10 GHz and ESD charging voltage of 1 kV has been suggested. Furthermore, a case study to implement and optimize the ESD protection structure based on an existing 0.13-μm CMOS technology has been presented and verified.     

基于多级维纳滤波的机载共形阵雷达杂波抑制方法研究

目前,多级维纳滤波器是一种收敛速度最快的降秩空时自适应处理算法,但它只适合于处理平稳随机信号,不能直接用于抑制非均匀的机载共形阵雷达杂波。该文在分析共形阵雷达杂波特性的基础上,提出采用俯仰向空域滤波改善杂波的非均匀性,改进了传统的协方差矩阵加权算法,最后形成了一种基于俯仰向空域滤波的协方差矩阵加权多级维纳滤波算法,用于抑制共形阵雷达杂波。仿真结果表明,该文方法抑制共形阵雷达杂波的综合性能优于现有其他方法,且计算复杂度低,收敛速度快,便于工程实现,在共形阵雷达杂波抑制中具有实际应用前景。     

应用于3.3kV IGBT的线性渐变掺杂结终端扩展的设计与优化

本文将线性渐变掺杂结终端扩展（LG-JTE）技术用于3.3kV IGBT并进行了试验验证。和采用多次光刻和离子注入传统结终端扩展技术不同,LG-JTE只用一张注入窗口宽度随与主结的距离线性变化的掩膜版。结合仿真设计了采用LG-JTE的IGBT,并在国内工艺平台上成功流片,其测试耐压达到3.7kV,接近理想的平行平面情形的耐压。     

Field Measurements with a 5.25 GHz Broadband MIMO-OFDM Communication System

Theoretical capacity calculations and corresponding simulations show significant capacity/throughput gains from MIMO systems. Whether these gains are achievable in a real system, deployed in a practical environment, depends on a variety of factors, such as the choice of the communication algorithms, analog impairments and the "quality" of the wireless channel to sustain MEMO communications. In this paper, a 5.25 GHz broadband MIMO-OFDM testbed is described along with field measurements conducted with it. The MIMO-OFDM communication algorithms and also the impact of analog impairments on the performance of the system are described. Detailed system calibration results are described which serve as a baseline for results of field measurements. The results of wireless measurements are compared with the theoretical capacity, computed with the channel estimates obtained during the demodulation process. The average achievable capacity in the indoor wireless environment is shown to be 9.97 bps/Hz (bits per sec per Hz) while the capacity loss due to analog impairments and the choice of algorithms is about 2.33 bps/Hz. Also, field measurements conducted with the system in various environments are presented comparing the average throughput/capacity achieved in each of these environments.