Master sintering curve concepts as applied to the sintering of molybdenum

Sintering experiments with various molybdenum powders are rationalized using a master sintering curve concept that collapses density, grain size, or other parameters onto a single curve. In this case, the integral work of sintering is developed and customized for different green densities. Construction of the master sintering curve is described to show how the curve can be normalized with respect to green density effects. Various grades of molybdenum for metal injection molding and die compaction are included in the analysis, processed over a range of heating cycles. Die-compacted samples of varying green densities are used to illustrate the efficacy of the new, normalized master sintering curve concept. Sintering cycle optimization is one possible outcome from this analysis.     

覆膜滤料的滤尘性能测试方法研究

由于覆膜滤料的结构和性能有别于普通滤料，因而普通滤料的滤尘性能测试方法不完全适用于覆滤料。本文作者在总结实践经验的基础上，提出了在覆膜滤料的滤尘性能测试中应注意的一些问题和应增加的测试项目。     

控制W9Cr3Mo4V低倍碳化物剥落的工艺改进

针对W9Cr3M04V轧制成品材低倍碳化物剥落的形成原因分析，得出一次碳化物颗粒粗大、在1／4D至中心区域聚集是导致低倍热酸浸试验碳化物剥落的主因；由此进行冶炼过程中注速（锭形）、浇注温度选择对比工艺试验，得出在原有冶炼＋轧制的工艺基础上选用2．2t锭、降低浇注温度（1489℃）能有效改善一次碳化物颗粒大小和聚集程度，进而有效降低低倍碳化物剥落倾向。     

Restraining the associations of anthracene fluorophore by chemically linking to poly(methyl methacrylate)

Associations (dimer or aggregate) of anthracene (An) fluorophores tend to interrupt the monomer emission and reduce the quantum yield (Φ_PL); therefore, poly(methyl methacrylate) (PMMA) chain was used in this study to chemically link to anthracene and to block the mutual associations among the anthracene fluorophores. With this aim, the target polymers were prepared by anionic polymerizations with 9,10‐dibromoanthracene/s‐butyllithium as initiating system to proceed polymerizations of methyl methacrylate (MMA) directly or in the presence of 1,1‐diphenylethylene (DPE). Use of DPE before addition of MMA produces stable initiating anionic species and avoids potential side reactions during polymerization; however, it also introduces four β‐phenylene rings around the central anthracene ring, which interfere with the corresponding emission pattern and reduce the Φ_PL (32%) value due to potential interactions between phenylene rings and anthracene. On the contrast, polymerization without participation of DPE results in polymer with central anthracene ring directly connected to two PMMA chains, which gives clean vibronic emission pattern with limited association emissions and enhanced Φ_PL (52%) value. Physical blending of anthracene by PMMA is less efficient to restrain the associations and results in a film of lower Φ_PL (20%). © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Intercalated clays from pentaerythritol stearate for use in polymer nanocomposites

Smectite clays treated with quaternary ammonium salts have been utilized for decades in paints, greases, cosmetics, and personal care products as rheological modifiers. They have also been used in industrial wastewater treatment extensively. In more recent times these surface modified clays have demonstrated benefits in polymer/clay nanocomposites. The use of quaternary ammonium modifiers limits the usefulness of these composites in food packaging because they are not approved for direct food contact. It would be advantageous to have surface modifying chemicals acceptable for direct food contact in these composites. This article reports research conducted on a promising surface modifier pentaerythritol stearate (PS), which is approved by the FDA for inclusion in food as a preservative. The surface modification of montmorillonite with PS is reported in detail as well as the production of nanocomposites with selected polymers made with the modified clay. Molecular modeling and purification of commercial PS samples indicate that the mono‐ and diesters are the critical surface modifiers, although the as received commercial material works well in forming intercalated clay complexes. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Viscoelastic properties of polyarylene ether nitriles/thermotropic liquid crystalline polymer blend

Polyarylene ether nitriles (PEN)/thermotropic liquid crystalline polymer (TLCP) blend was prepared via melt mixing. The immiscible phase morphologies, linear and nonlinear, as well as transient viscoelastic properties of the blend were studied using SEM, rheometer, and DMA. The linear dynamic viscoelastic behavior of the blend shows temperature dependence due to further evolution of the immiscible morphology and, as a result, the principle of time‐temperature superposition (TTS) is invalid. In the steady shear flow, the discrete TLCP phase is difficult to be broken up because of the high viscosity ratio of the blend systems, while is easy to be coarsened and followed by elongation, and finally, to form fibrous morphology at high TLCP content and high shear level. During this morphological evolution process, the transient stress response presents step increase and nonzero residual relaxation behavior, leading to increase of the dynamic viscoelastic responses after steady preshear. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and adsorption behavior of a cellulose‐based,mixed‐mode adsorbent with a benzylamine ligand for expanded bed applications

A novel mixed‐mode expanded bed adsorbent with anion‐exchange properties was explored with benzylamine as the functional ligand. The cellulose composite matrix, densified with stainless steel powder, was prepared with the method of water‐in‐oil suspension thermal regeneration. High activation levels of the cellulose matrix were obtained with allyl bromide because of the relative inertness of the allyl group under the conditions of the activation reaction. After the formation of the bromohydrin with N‐bromosuccinimide and coupling with benzylamine, the activated matrix was derived to function as a mixed‐mode adsorbent containing both hydrophobic and ionic groups. The protein adsorption capacity was investigated with bovine serum albumin as a model protein. The results indicated that the prepared adsorbent could bind bovine serum albumin with a high adsorption capacity, and it showed salt tolerance. Effective desorption was achieved by a pH adjustment across the isoelectric point of the protein. The interactions between the cell and adsorbent were studied, and the bioadhesion was shielded by the adjustment of the salt concentration above 0.1M. Stable fluidization in the expanded bed was obtained even in a 2% (dry weight) yeast suspension. The direct capture of target proteins from a biomass‐containing feedstock without extra dilution steps could be expected with the mixed‐mode adsorbent prepared in this work, and this would be especially appropriate for expanded bed adsorption applications. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation of brush-like crystals of poly[2,6-(1,4-phenylene)-benzobisimidazole]

Poly[2,6-(1,4-phenylene)-benzobisimidazole] (PPBI) crystals were prepared by using reaction-induced crystallization of oligomers during solution polymerization of 1,2,4,5-tetraaminobenzene and diphenyl terephthalate. Polymerizations were carried out at a monomer concentration of 4.3 × 10⁻² mol L⁻¹ at 350 °C for 6 h. Brush-like PPBI crystals were obtained in a mixture of structural isomers of dibenzyltoluene, in which many needle-like crystals came out vertically from the surface of the ribbon-like crystals. Average width and thickness of the ribbon-like crystals were 0.75 μm and 0.11 μm, respectively. And average length and diameter of the needle-like crystals were 0.36 μm and 50 nm, respectively. The brush-like crystals possessed high crystallinity and exhibited good thermal resistance. The ribbon-like crystals were formed by the crystallization of imidazole oligomers at an initial stage of polymerization, and then the needle-like crystals grew from the surface of the ribbon-like crystals. Polymerization occurred on the crystals when the oligomers were crystallized, leading to the high molecular weight PPBI crystals.     

真空蒸馏脱硒的研究

本文从理论上分析了真空蒸馏脱Se的影响因素时间和温度,并通过实验给予验证,提出了最佳条件,对工业采用真空蒸馏脱出含Se物料中的Se具有一定的指导性。