直纺长丝工艺中聚酯熔体端羧基值控制的工业研究

本文从工业生产的实践出发对杜邦聚酯技术直接纺工艺中端羧基控制进行了研究。通过对熔体端羧基值对无油长丝端羧基、粘度及纺丝加工影响的分析 ,阐明了聚酯端羧基控制范围 ;通过摸索三个反应釜工艺条件对端羧基值的影响 ,找出了端羧基工业控制的有效途径 ,为同类技术装置生产提供了依据     

陶瓷纳米粉体的分散与表征

总结了复合材料制备过程中纳米颗粒的分散方法，对其机理进行探讨，总结了纳米粒径及复合材料的表征方法，并展望了纳米复合材料的发展前景。     

二种双邻位甲基取代的聚芳醚酮类树脂的合成与性能

合成二种双邻位甲基取代的聚芳醚酮类聚合物,聚芳醚酮醚酮酮(DM-PEKEKK)和聚芳醚酮酮醚酮酮(DM-PEKKEKK),用FT-IR、1H NMR、DSC、WAXD、TG等技术对其进行表征,研究表明:较之于未取代的PEKEKK和PEKKEKK玻璃化转变温度和溶解性能大幅度提高,热分解温度有所下降,但均在450℃以上.     

泡沫微晶玻璃的研究进展

概述了泡沫微晶玻璃的性能及应用,综述了泡沫微晶玻璃的研究进展,并对泡沫微晶玻璃的发展方向进行了展望。     

A kinetic model for polystyrene (PS) pyrolysis reaction

A mathematical model for the pyrolysis reaction of polystyrene (PS) in a semi-batch reactor has been presented. The thermal degradation of PS was flexibly modeled by a combination of random and specific chain-end scissions. Numerical simulation was used to investigate the effect of operating conditions on the PS products spectrum, the results of which were validated by the experimental data. It was found that as the reaction temperature increased (decreased), the monomer fraction in the products became lower (higher) while the trimer higher (lower). No significant variation in the product composition was, however, observed while constant temperature was maintained. These results indicate the reaction temperature is an effective manipulated variable for the control of products composition of PS pyrolysis. The calculation of the optimum temperature trajectories through the optimization study can thus be of interest for achieving productivity enhancement in plastics pyrolysis processes. This paper is dedicated to Professor Dong Sup Doh on the occasion of his retirement from Korea University.     

接触轨玻璃钢防护罩研制

本文介绍了地铁接触轨防护罩的结构设计、原材料选择、制造工艺、性能检测、质量控制等.     

碘量法测定二氧化氯要点分析

二氧化氯是一种安全高效的消毒剂。采用国家行业标准中有效二氧化氯含量的测定方法的测量结果差异较大，用碘量法测定稳定态二氧化氯溶液中的有效二氧化氯含量时，活化反应的速度对测定有效二氧化氯的含量有一定影响。通过条件实验确定了碘量法测定有效二氧化氯含量的最佳测试条件，即：活化时间13min，盐酸稀释至与水体积比1：4，参考电压140V，可确保实验结果的平行性和再现性。     

液氯气化工艺及安全

介绍了液氯气化的工艺过程及所采取的相应安全措施。     

酰胺类除草剂对红小豆的安全性

针对当前红小豆农业生产中大量应用的酰胺类除草剂并丙草胺、并丙甲草胺，研究其对红小豆苗期的安全性。研究表明，在低温、土壤墒情好的条件下两种药剂均对红小豆不安全，主要表现在影响出苗率、抑制生长、根体积明显减少、真叶叶片皱缩扭曲、严重的叶缘开始发黄、根瘤减少、逐渐枯死。两种药剂药害程度相近、随剂量增加症状明显加重，高用量时拱土期施药比播后立即施药的药害相对较轻，随有机质含量的降低而药害加重。     

Electrochemical performance of nanocrystalline Li3V2(PO4)3/carbon composite material synthesized by a novel sol–gel method

A novel sol–gel method based on V₂O₅·nH₂O hydro-gel was developed to synthesize nanocrystalline Li₃V₂(PO₄)₃/carbon composite material. In this route, V₂O₅·nH₂O hydro-gel, NH₄H₂PO₄, Li₂CO₃ and high-surface-area carbon were used as starting materials to prepare precursor, and the Li₃V₂(PO₄)₃/carbon was obtained by sintering precursor at 750 °C for 4 h in flowing argon. The sol–gel synthesis ensures homogeneity of the precursors and improved reactivity. The sample was characterized by XRD, SEM and TEM. X-ray diffraction results show Li₃V₂(PO₄)₃ sample is monoclinic structure with the space group of P2₁/n. The TEM image indicates that the Li₃V₂(PO₄)₃ particles modified by conductive carbon are about 70 nm in diameter. The Li₃V₂(PO₄)₃/carbon system showed that the discharge capacities in the first and 50th cycle are about 155.3 and 143.6 mAh/g, respectively, in the range of 3.0–4.8 V. The sol–gel method is fit for the preparation of Li₃V₂(PO₄)₃/carbon composite material which may offer some favorable properties for commercial application.