油田放射性作业人员外周血淋巴细胞染色体畸变的观察

本文调查了油田212例受γ射线和中子混合辐射照射的作业人员和30例正常人的外周血淋巴细胞染色体畸变。作业人员受γ射线照射的人均年受照剂量为1.28mGy。调查结果表明,放射性测井人员与正常人相比染色体畸变率有显著差异。     

A new kind of compound solid-state quasi-optical power combiner

In this paper, a new kind of solid-state quasi-optical power combiner is presented. It consists of two or more singlecavity multiple-device power combiners and a Fabry-Perot cavity. The experimenal results using six Gunn diodes at X-band show that the total output power is higher than 400 mW, the total combining efficiency is as high as 83%, and the frequency stability is better than 10^?5.     

底水油藏射孔优化设计

为了优化底水油藏的生产参数，研究了不同产量时射孔长度的优化方法。采用球面流和径向流相结合的模型推导了临界产量和无水采油量的计算公式，分别以临界产量和无水采油量为标准，对胜利油田桩西区块底水油藏上6口油井的射孔长度进行了优化设计，优化结果表明，对于底水油藏应首先按照临界产量对射孔长度进行优化设计，如果得到的最大临界产量不符合实际生产的要求，就应按照无水采油量进行射孔优化设计。研究表明，当油井产量超过临界产量后，以临界产量为标准得到的优化射孔长度会减小油井的无水采油量。     

天然气的储存

随着能源结构的调整,天然气在一次能源中的比重逐步增大,天然气的储存成为人们日益关注的课题,作者就此作一综述。     

基于HMM方法的动态手势轨迹训练性能研究

基于HMM(Hidden Markov Model,隐形马尔可夫模型)对动态手势轨迹的训练是手势识别的关键技术之一。本文对HMM的模型训练采用Baum.Welch算法,并分别从迭代次数,样本个数选取,以及模型初值选取等方面对动态手势轨迹的训练性能进行了研究。实验结果表明HMM方法对具有时空特性的动态手势轨迹识别是非常有效的。     

Optimal control and operation of drum granulation processes

Process optimisation and optimal control of batch and continuous drum granulation processes are studied in this paper. The main focus of the current research has been: (i) construction of optimisation and control relevant, population balance models through the incorporation of moisture content, drum rotation rate and bed depth into the coalescence kernels; (ii) investigation of optimal operational conditions using constrained optimisation techniques; (iii) development of optimal control algorithms based on discretized population balance equations; and (iv) comprehensive simulation studies on optimal control of both batch and continuous granulation processes. The objective of steady state optimisation is to minimise the recycle rate with minimum cost for continuous processes. It has been identified that the drum rotation-rate, bed depth (material charge), and moisture content of solids are practical decision (design) parameters for system optimisation. The objective for the optimal control of batch granulation processes is to maximize the mass of product-sized particles with minimum time and binder consumption. The objective for the optimal control of the continuous process is to drive the process from one steady state to another in a minimum time with minimum binder consumption, which is also known as the state-driving problem. It has been known for some time that the binder spray-rate is the most effective control (manipulative) variable. Although other possible manipulative variables, such as feed flow-rate and additional powder flow-rate have been investigated in the complete research project, only the single input problem with the binder spray rate as the manipulative variable is addressed in the paper to demonstrate the methodology. It can be shown from simulation results that the proposed models are suitable for control and optimisation studies, and the optimisation algorithms connected with either steady state or dynamic models are successful for the determination of optimal operational conditions and dynamic trajectories with good convergence properties.     

现场总线技术的特点及其在热电站的应用

阐述了现场总线技术的含义、主要特点和优点,对比了现场总线控制系统与DCS系统的区别,介绍了现场总线技术在洛阳石化分公司热电站的典型应用及其发展前景。     

CO毒化AB5型合金分形特征研究

研究了三种贮氢合金 L a Ni5、L a Ni4 .7Al0 .3、Ml Ni4 .5Al0 .5被 10 0× 10 - 6 CO毒化后的分形特征 ,求出这三种合金在含 10 0× 10 - 6 CO的氢中循环 ,分维分别为 0 .2 5 4 7、0 .170 9、0 .0 72 5。可以较好的解释合金被毒化的宏观现象。     

3-N-丙酰基-2-芳基-5-(3-碘苯基)-1,3,4-(口恶)唑啉类化合物的合成及表征

以3-碘苯甲酸为原料,在浓硫酸作用下与乙醇反应制得3-碘苯甲酸乙酯(1),再以无水乙醇为溶剂,在105℃化合物1与80％的水合肼反应8 h,制得3-碘苯甲酰肼(2)。在无水乙醇中,在90～95℃化合物2分别与4-甲基苯甲醛、2-氯苯甲醛、4-氯苯甲醛、4-羟基苯甲醛、2,4-二氯苯甲醛、4-甲氧基苯甲醛、3-硝基苯甲醛、4-硝基苯甲醛和4-二甲氨基苯甲醛反应得到相应的酰腙[3(a～i)]。最后化合物3(a～i)分别与丙酸酐脱水环化成了3-N-丙酰基-2-芳基-5-(3-碘苯基)-1,3,4-(口恶)唑啉类化合物[4(a～i)],收率分别为86．2％,70．5％, 80．1％,68．2％,62．4％,75．2％,73．2％,70．5％和63．2％。并通过元素分析,IR,1H NMR和MS对化合物4(a～i)的结构进行了表征。