The effects of pressure on the isothermal fluid behavior of bituminous coals

An investigation into the effects of pressure (helium gas) on the isothermal fluid behavior includes: (1) the effect of pressure on the rate of melting and coking as evidenced by the rate constants k(melt) and k(coke); (2) the effect of pressure on the energies of activation of melting and coking; (3) the effects of pressure on the characteristic times; (4) the effects of pressure on the maximum isothermal fluidity. Results from the effects of pressure on k(melt) revealed that it was generally the high total sulfur, low nitrogen, low reactives/mineral matter ratio, medium rank coals which show the greatest increase in k(melt), whereas the highest rank coals show the least decrease in k(coke). The energies of activation of melting and coking were not significantly affected by pressure. The investigation also reveals increases or decreases in the respective times of softening, maximum fluidity, resolidification and total time of fluid behavior under isothermal pressurized conditions. There appears the possibility that these shifts may be rank dependent. Additionally, the lower rank coals show the largest relative increase in their fluidities when subjected to pressure. Empirical relationships were derived in order to quantitatively predict the maximum isothermal fluidity for most (fluid) coals at a given pressure.     

An expert diagnostic system for the MACRO experiment at the GranSasso Laboratory

The maintenance of the MACRO (a Monopoles, Astrophysics and Cosmic Ray Observatory), a large-area detector that will be used to search for rare constituents or phenomena in cosmic radiation penetrating deep underground, is addressed. A real-time expert system for diagnosing detector and data acquisition system anomalies, which is based on the NEXPERT commercial tool, is described. It performs online diagnosis and, if an abnormal condition is identified, takes the appropriate action to reduce the unavailability of the apparatus. The data acquisition system is CAMAC-based, and the sensor modules, which gather the significant values for diagnosis, are implemented in the VME crate     

Seasat over-land scatterometer data. I. Global overview of theKu-band backscatterer coefficients

Statistics on the backscatter coefficient σ⁰ from the Ku-band Seasat-A Satellite Scatterometer (SASS) collected over the world's land surfaces are presented. This spaceborne scatterometer provided data on σ⁰ between latitude 80° S and 80° N at incidence angles up to 70°. The global statistics of vertical (V) and horizontal (H) polarization backscatter coefficients for 10° bands in latitude are presented for incidence angles between 20° and 70° and compared with the Skylab and ground spectrometer results. Global images of the time-averaged V polarization σ⁰ at a 45° incidence angle and its dependence on the incidence angle are presented and compared to a generalized map of the terrain type. Global images of the differences between the V an H polarization backscatter coefficients are presented and discussed. The most inhomogeneous region, which contains the deserts of North Africa and the Arabian Peninsula, is studied in greater detail and compared with the terrain type     

Systematic characterization of Cl2 reactive ion etchingfor improved ohmics in AlGaN/GaN HEMTs

Pre-metal-deposition reactive ion etching (RIE) was performed on an Al_0.3Ga_0.7N/AlN/GaN heterostructure in order to improve the metal-to-semiconductor contact resistance. An optimum AlGaN thickness for minimizing contact resistance was determined. An initial decrease in contact resistance with etching time was explained in terms of removal of an oxide surface layer and/or by an increase in tunnelling current with the decrease of the AlGaN thickness. The presence of a dissimilar surface layer was confirmed by an initial nonuniform etch depth rate. An increase in contact resistance for deeper etches was experienced. The increase was related to depletion of the two-dimensional (2-D) electron gas (2-DEG) under the ohmics. Etch depths were measured by atomic force microscopy (AFM). The contact resistance decreased from about 0.45 Ωmm for unetched ohmics to a minimum of 0.27 Ωmm for 70 Å etched ohmics. The initial thickness of the AlGaN layer was 250 Å. The decrease in contact resistance, without excessive complications on device processing, supports RIE etching as a viable solution to improve ohmic contact resistance in AlGaN/GaN HEMTs     

Reduced and differential parallel interference cancellation forCDMA systems

Since code division multiple access systems in multipath environments suffer from multiple access interference (MAI), multiuser detection schemes should be used in the receivers. Parallel interference cancellation (PIC) is a promising method to combat MAI due to its relatively low computational complexity and good performance. It is shown that the complexity of PIC is still high for realistic scenarios in terms of the symbol rate, the number of users, spreading gain, and multipath components. However, two novel methods are introduced to reduce significantly the complexity without sacrificing performance. The first approach, called reduced PIC, takes advantage of the composition of the interference to concentrate interference cancellation only on significant terms. The second approach, called differential PIC, exploits the multistage character of PIC to avoid unnecessary double calculations of certain terms in consecutive stages. It is shown that a combination of both approaches leads to a performance very close to the single-user bound whereas the complexity can be kept on the order of the conventional RAKE receiver     

Sequential tripping strategy for a transmission network back-upprotection expert system

This paper describes a sequential tripping strategy used in a wide area back-up protection expert system (BPES) to combat situations in which protection relays have maloperated or information is missing. The BPES is an innovative back-up protection scheme designed to prevent the occurrence of widespread blackouts. The BPES evaluates the certainty that transmission lines are likely to be affected by the fault and uses a sequential tripping strategy to isolate the fault if a firm decision is not available due to maloperated relays and/or missing information. The mode of analysis and the sequential tripping strategy ensures that the BPES will clear a fault at minimum risk to the network. An example is included to demonstrate how the certainty factor based sequential tripping strategy is employed by the BPES to clear a fault which occurred on the South Western part of the UK National Grid System     

Bonding in cotton fiber from formaldehyde-free crosslinks

Cotton fabric was crosslinked with five agents, three of which were prepared form formaldehyde and two of which were formaldehyde-free. The formaldehyde-free agents produced less bonding between layers in the laminated microstructure of the cotton fiber. One agent, 4,5-dihydroxy-1,3-dimethyl-2-imidazolidinone, gave no evidence of any interlayer bonding. All five agents gave the same relationship between wrinkle recovery angle and molar substitution on the cotton up to moderate recovery angles, but only agents based on formaldehyde gave higher wrinkle recovery angles with additional reaction. Intralayer crosslinking did not reduce absorptivity, as shown by moisture regain and dye receptivity, but did restrict swelling in cupriethylenediamine hydroxide to the same extent as combined interlayer and intralayer crosslinking. The decrease in extensibility of treated fabric with increasing wrinkle recovery angle was the same with all agents. These results indicate the regions of the fiber that are important for each of these properties.     

Generalisations of Heyman's and Foulkes' theorems using dual formulation

Existing duality principles in structural optimisation are briefly reviewed and then they are extended to structures with segment-wise constant cross-sections. All theories are discussed in the particular context of optimal plastic beam design with symmetric convex specific cost functions and are confirmed by independent calculations on illustrative examples. It is shown that the optimal solution is always associated with a displacement field in which the mean absolute curvature value for each segment equals the subgradient of the specific cost function, with respect to the maximum absolute moment value for that segment. Moreover, the dual problem consists of the maximisation of the difference of two terms: the first one is the integral of the product of load and deflection (external work), and the second is the sum of products of segment lengths and the mean complementary cost values (taken with respect to the mean absolute curvature for that segment). Finally, some tentative proposals for a class of non-convex optimisation problems are presented. For special cases, the proposed general statements reduce to theorems by Heyman, Foulkes and Hemp.     

Resonant neutron filters in elemental analysis and radiography

Translated from Atomnaya Énergiya, Vol. 67, No. 4, pp. 271–274, October, 1989.