CT图像局域阴影特征小波阈值提取方法

利用当前方法对CT图像局域阴影特征提取时未对CT图像进行预处理,存在峰值信噪比低、ROC曲线低和特征分离度低的问题.提出CT图像局域阴影特征小波阈值提取方法,该方法确定小波阈值后对CT图像进行去噪,同时利用线性、分段线性以及非线性三种灰度变换方式以此增强CT图像分辨率,以便更加清晰地分辨CT图像局域阴影,并利用二维Dau-bechies小波分解CT图像局域阴影,将其分成若干个小图像后利用概率密度分布求解特征值,最终结合所有图像的特征值实现CT图像局域阴影特征提取.实验结果表明,所提方法的峰值信噪比高、ROC曲线高和特征分离度高.     

Performance evaluation of anti-radiation based on the gamma degradation process

In the environment of space radiation, the high-energy charged particles or high-energy photons acting on a spacecraft can cause either temporary device degradation or permanent failure. The traditional probability model is difficult to obtain reliable estimation of unit radiation resistance performance with small samples. Considering that different products will change differently after high-energy particle radiation, we construct a model based on the gamma degradation process. This model can efficiently describe the law of unit radiation resistance variation with the total radiation dose levels under the effect of the total dose and displacement damage. Finally, the proposed model is used to assess the anti-radiation performance of the N-channel power MOSFET device STRH60N20FSY3 produced by STM to obtain average unit radiation resistance, survival probability, survival function, etc.     

读者决策采购（PDA）成功实施的关键性因素分析

读者决策采购作为一种全新的基于读者需求的资源建设模式,目前国内还没有高校图书馆实施。介绍了读者决策采购面临的问题,提出PDA要在我国高校图书馆成功实施,需制定严格的标准、选择合适书商并及时进行跟踪与评价。     

氧化鸡肉脂肪制备肉味香精前体物质的研究

研究以鸡肉脂肪为主要原料制备肉味香精的前体物质,通过单因素和正交试验确定氧化反应的最佳反应条件.结果表明氧化鸡肉脂肪的最佳条件是:氧化温度为120℃,氧化时间为3h,VE的添加量为1.0%,不添加水和NaCl.在最优条件下进行氧化试验,得到产物的酸值和过氧化值分别为1.472 mg/g和193.51 mmol/kg,感官评价值为4.905,具有典型特征的鸡肉香气.     

Engineering all-aromatic polyamide surface from hydrophilic to superhydrophobic and the accelerated strategy

Being a new kind of nanomaterials, aromatic polyamide nanofibers (ANF) have been much highlighted in recent studies. We here demonstrate an isopropyl alcohol (IPA) accelerated chemical cleavage on poly (p-phenylene terephthalamide) chopped fibers, which provides an efficient preparation method of ANF. The comprehensive study on the processes accelerated by different alcohols revealed that the preparation time of ANF in the mixed medium of dimethyl sulfoxide (DMSO)-alcohol (20:1 in volume) was shorten to 45 min and 75 min for methanol (ethanol) and isopropanol, respectively. However, the nanofibers prepared in DMSO-IPA exhibited the minimum in axial and radial dimensions, providing the finest and most uniform diameter of 16 nm. The corresponding ANF films through vacuum assisted filtration also showed the highest tensile strength of 150 MPa, in comparison with those of the ANF films prepared using other alcohols, which were about 110 MPa. Furthermore, ANF/silicon hybrid films were prepared by the ionic ring-opening reaction followed by the alkoxysilane condensation and nanoparticle fabrication. By changing the organo functional groups in the alkoxysilane, the surface of the films were adjustable in a wide contact angle range from 56° (hydrophilic) to 150° (superhydrophobic), suggesting the amendable interfacial properties potential applicable to composite fabrication with most of the resin matrix.     

EFFECT OF SILICON ON THE TRANSITION OF BRITTLENESS IN A NICKEL BASE WROUGHT SUPERALLOY

Ni-15Cr-6W-3Mo-2Al-2Ti变形高温合金的室温抗张强度、塑性和冲击性能,随着合金中Si含量的变化呈现马鞍型的变化,即在0.4—0.6％Si范围内出现一个低塑性、低拉伸强度和低冲击韧性区。造成这种现象的本质原因是由于Si含量变化改变了晶界碳化物沉淀析出顺序、析出类型、析出量和析出形态。该合金晶界碳化物析出可分为四个阶段:第一阶段,<0.1％Si时,只有单一的M_(23)C_6析出;第二阶段,>0.1％Si以后,除M_(23)C_6外,M_6C开始析出,一直到0.4％Si时增加2缓慢;第三阶段,0.4—0.6％Si时,M_6C大量析出逐渐取代M_(23)C_6;第四阶段,>0.6％Si以后,M_6C量占绝对优势,但增加幅度比第三阶段小得多。从晶界形态来看,第一、二、四阶段皆属不连续的链状形式,只有第三阶段晶界呈现连续膜状。因此,造成性能下降的原因不是因为析出M_6C,而是它的形态,当它以颗粒状分布在晶界上时是一个很好的强化相。第三阶段的不正常析出是性能下降的本质因素。本研究结果打破了只要镍基合金中MO+1/2>W>6％(重量百分比)就形成M_6C的经验判据,“Si”才是该合金碳化物沉淀析出过程的控制因素。本文还对比了冶炼工艺差别对碳化物析出过程的影响。     

简单断面孔型计算机绘图系统简介

介绍了简单断面孔型计算机绘图系统的编制方法、使用范围 ,计算机绘图的步骤及特点     

基于MATLAB的热定型机PID张力控制器设计

文章介绍了热定型机的工作原理,及其定型过程中张力系统控制结构图,并以此为基础建立了张力控制系统的数学模型.基于比例积分微分(PID)控制器的原理,利用MATLAB软件设计了张力控制器,其编写的PID参数整定函数能作为MATLAB函数进行直接调用.实验和仿真结果表明:该控制器完全满足张力控制系统的性能要求,降低了超调量,提高了系统的动静态性能;同时设计简单、易于实现.     

多目标优化理论在蜂窝夹芯结构设计中的应用

在确定了设计变量及目标函数的基础上,根据结构本身的要求,推导出用于多目标优化的5个约束条件.根据多目标优化理论,采用乘除法对蜂窝夹芯结构进行了评价函数的构造,并用VC语言编制了钢质蜂窝夹芯减振板结构的优化程序,该程序可实现结构尺寸及性能的优化,并计算出各目标函数的最终值.     

Performance of positive and negative electrodes in amorphous manganese oxide supercapacitor

Using potassium permanganate and acetic manganese as the reactants, amorphous manganese oxide was prepared with mechanochemical method. XRD was used for microstructure characterization, while cyclic voltammetry and constant current charge-discharge were used for electrochemical performance testing. The positive electrode （PE） and negative electrode （NE） were investigated respectively in amorphous manganese oxide supercapacitor, aiming to find their different performances in charging-discharging. The results show that the crystalline structure is destroyed in both the PE and NE material during charge-discharge process. Thereinto, the NE suffers a bit more seriously. When cycling, the PE potential scope diminishes while the NE potential scope enlarges. The increased inner resistance makes the NE curves almost bended to be a right angle, but not the PE curves. The cell＇s equivalent series resistance （ESR） is more dependent on the NE, and the capacitance is mainly determined by the rapid descent of the NE potential range. The capacitances of the NE are highly rate-dependent, decreasing from 121.3 to 53.1 F/g, by 56.2%, over the range of 5-25 mV/s. However, the PE appears to be weakly dependent and its capacitance is only dropped by 22.1%.