Energy content of world trade

This paper constructs a comprehensive dataset of oil and total energy embedded in world trade of manufacturing goods for 73 countries from 1978 to 2000. Applying the data to debates on the dependency on foreign energy sources makes clear that achieving complete energy independence in the foreseeable future is unlikely to be feasible and may not be desirable. Applying it to the discussion of environmental Kuznets curves (EKCs) highlights an important distinction between production and consumption of energy. Richer countries use relatively less energy in their industrial production yet still consume relatively large amounts of energy indirectly. A further investigation largely excludes structural shifts of production in and out of the manufacturing sector as an explanation for the downward-sloping portion of the EKC. Country-level analyses add caveats but show tentative support for the cross-country conclusions.     

Interpretation und Modellierung der Temperaturverteilung in einer Sicker- und Grundwassermeßstelle der Braunkohlentagebaukippe Cospuden

The time and depth depending temperature distribution in an isolated expolratory hole in the dump of former open-cast lignite mine Cospuden is analyzed and interpreted. By means of hydrodynamical modeling several model assumptions are tested on following influences: seasons, hydraulic situation, geochemical processes, sampling regime, specific features of drilling, and support of bore hole. Best correspondence between measured temperature distribution and model assumptions is obtained by the following primary processes: seasonal influences of earth's surface and reactive processes in the dump. Then are favored: Slow exothermic reactions with an high extant of reaction heat in the depth of 2 to 6 m, slow strongly exothermic reactions above the piezometric water level in 9 to 13 m depth with a maximum near 11 m, and simultaneously run of fast endothermic and slow weakly exothermic reactions in the zone of saturation of the bore hole. It is tried to assign chemical reactions to these processes.     

Parkhaus CHL Centre Hospitalier de Luxembourg: Verbunddecken mit Faserbeton

Multi‐storey car park “centre hospitalier de Luxembourg“: Composite decking with fibre reinforced concrete. A multi‐storey car park was built for the “centre hospitalier de Luxembourg” in 2006 within a construction time of only eight months. It is the first application of a composite decking Cofraplus 60 with fibre reinforced concrete. The time for installing the rebars was extremely reduced. The slabs of the 4 storey building of an area of 125 m × 43,6 m have no joints. The car park offers 643 parking spaces and a helicopter pad on the roof.     

Optical properties of highly transparent polypropylene cast films: Influence of material structure,additives, and processing conditions

Polypropylene homopolymers and ethylene/propylene‐random‐copolymers formulated with and without anti‐blocking additives were extruded to cast films with an industrial scale extruder equipped with a soft box, a specific air knife that expels a higher volume of air at lower velocity. The films were analyzed as to their optical properties haze and clarity. A comprehensive topographical characterization was performed using atomic force microscopy (AFM) and confocal microscopy. To obtain morphological information on a nanometer scale AFM phase imaging, micro‐thermal analysis and small angle X‐ray scattering (SAXS) were done. A significant effect of additives and processing conditions on the film topography and the optical properties was revealed. The films without anti‐blocking and antacid aids showed the best optical properties and lowest vertical roughness fluctuations. In contrast, the addition of anti‐blocking and antacid aids reduced the optical properties associated with an increase in surface roughness. While for films without anti‐blocking aids an enhanced soft box condition resulted in lower vertical fluctuations of roughness and better optical properties, the behavior was in reverse for films with anti‐blocking aid. By means of SAXS crystalline lamellae with a thickness of about 2.5 nm were detected. High‐resolution phase imaging AFM yielded thicker crystal lamellae on the film surface. POLYM. ENG. SCI., 46:520–531, 2006. © 2006 Society of Plastics Engineers.     

ESBL-producing E. coli in Austrian sewage sludge

The aim of this study was to investigate the degree of contamination of sewage sludge with ESBL-producing Escherichia coli strains and the effectiveness of different sewage sludge treatment methods.Monthly sewage sludge samples were collected between January and September 2009 in 5 different sewage treatment plants and tested for the presence of ESBL E. coli. In addition, the number of colony forming units (CFU) of E. coli and coliform bacteria before and after the different sludge treatment methods (aerobic/anaerobic digestion, lime stabilization, and thermal treatment) was investigated.Of the 72 sewage sludge samples investigated, ESBL-positive E. coli were found in 44 (61.1%) sewage sludge samples. The classification of β-lactamase groups was carried out in 15 strains resulting in the detection of 2 different groups (CTX-M and TEM) of bla genes. All 15 of them had a CTX-M gene and 4 of these strains furthermore carried a TEM gene.With regard to the CFU of E. coli and coliform bacteria, thermal treatment and lime stabilization following dehydration sufficiently reduced pathogen concentrations. The plants using merely stabilization and dehydration showed an increase of E. coli and coliform bacteria and thus also an increase in ESBL-producing E. coli.     

Development of Endothelial Cell Networks in 3D Tissues by Combination of Melt Electrospinning Writing with Cell‐Accumulation Technology

A remaining challenge in tissue engineering approaches is the in vitro vascularization of engineered constructs or tissues. Current approaches in engineered vascularized constructs are often limited in the control of initial vascular network geometry, which is crucial to ensure full functionality of these constructs with regard to cell survival, metabolic activity, and potential differentiation ability. Herein, the combination of 3D‐printed poly‐ε‐caprolactone scaffolds via melt electrospinning writing with the cell‐accumulation technique to enable the formation and control of capillary‐like network structures is reported. The cell‐accumulation technique is already proven itself to be a powerful tool in obtaining thick (50 µm) tissues and its main advantage is the rapid production of tissues and its ease of performance. However, the applied combination yields tissue thicknesses that are doubled, which is of outstanding importance for an improved handling of the scaffolds and the generation of clinically relevant sample volumes. Moreover, a correlation of increasing vascular endothelial growth factor secretion to hypoxic conditions with increasing pore sizes and an assessment of the formation of neovascular like structures are included.