Modeling and Simulation for Transient Thermal Analyses Using a Voltage-in-Current Latency Insertion Method

This article presents a modeling and simulation method for transient thermal analyses of integrated circuits(ICs) using the original and voltage-in-current(VinC) latency insertion method(LIM). LIM-based algorithms are a set of fast transient simulation methods that solve electrical circuits in a leapfrog updating manner without relying on large matrix operations used in conventional Simulation Program with Integrated Circuit Emphasis(SPICE)-based methods which can significantly slow down the sol...     

Simultaneous fractionation of multiple classes of polyphenols from honeybush tea using solid-phase extraction

The structural diversity of polyphenols and the inherent limitations of current extraction techniques pose a challenge to extract polyphenols using a simple and green method. Hence, in this study, a method was developed to simultaneously fractionate multiple classes of polyphenols by only varying ethanol-water solutions. Honeybush tea, which is rich in polyphenols, was selected as a model for this study. Solvent extraction followed by solid-phase extraction (SPE) was developed to obtain a polyphenol-rich fraction from six honeybush samples. Based on a gradient elution programme (10%, 30%, 50%, 70% and 90% (v/v) ethanol-water solution) of SPE, the Strata X cartridge showed a better recovery of most targeted polyphenols under 0.9 mL of the drying volume and 1 mL min⁻¹ of the dispensing speed. The elution programme for fractionating most polyphenols was as follows: single elution with 50% ethanol, followed by twice elution with 70% ethanol. The antioxidant capacity was used to analyse the differences among the polyphenol-rich fractions from six honeybush samples. Principal component analysis (PCA) revealed that unfermented C. genistoides (GG) has the greatest antioxidant capacity among the honeybush species studied. Additionally, mangiferin, isomangiferin and vicenin-2 were the main contributors to the antioxidant capacity in six honeybush fractions according to the correlation study.     

Targeted Delivery of Anesthetic Agents to Bone Tissues using Conductive Microneedles Enhanced Iontophoresis for Painless Dental Anesthesia

Pain management during dental procedures is a cornerstone for successful daily practice. In current practice, the traditional needle and syringe injection is used to administer local anesthesia. However, the appearance of long needles and the pain associated with it often leads to dental anxiety deterring timely interventions. Microneedles (MNs) have emerged as a minimally invasive alternative to hypodermic needles and shown to be effective in transdermal drug delivery applications. In this article, the potential use of MNs for local anesthesia delivery in dentistry is explored. The development of a novel conductive MN array that can be used in combination with iontophoresis technique to achieve drug penetration through the oral mucosa and the underlying bone tissue is presented. The conductive MN array plays a dual-role, creating micro-conduits and lowering the resistance of the oral mucosa. The reduced tissue resistance further enhances the application of a low-voltage current that is able to direct and accelerate the drug molecules to target the sensory nerves supplying teeth. The successful delivery of lidocaine using this new strategy in a clinically relevant rabbit incisor model is shown to be as effective as the current gold standard.     

Facile Synthesis and Characterization of Palm CNF-ZnO Nanocomposites with Antibacterial and Reinforcing Properties

Cellulose nanofibers (CNF) isolated from plant biomass have attracted considerable interests in polymer engineering. The limitations associated with CNF-based nanocomposites are often linked to the time-consuming preparation methods and lack of desired surface functionalities. Herein, we demonstrate the feasibility of preparing a multifunctional CNF-zinc oxide (CNF-ZnO) nanocomposite with dual antibacterial and reinforcing properties via a facile and efficient ultrasound route. We characterized and examined the antibacterial and mechanical reinforcement performances of our ultrasonically induced nanocomposite. Based on our electron microscopy analyses, the ZnO deposited onto the nanofibrous network had a flake-like morphology with particle sizes ranging between 21 to 34 nm. pH levels between 8–10 led to the formation of ultrafine ZnO particles with a uniform size distribution. The resultant CNF-ZnO composite showed improved thermal stability compared to pure CNF. The composite showed potent inhibitory activities against Gram-positive (methicillin-resistant Staphylococcus aureus (MRSA)) and Gram-negative Salmonella typhi (S. typhi) bacteria. A CNF-ZnO-reinforced natural rubber (NR/CNF-ZnO) composite film, which was produced via latex mixing and casting methods, exhibited up to 42% improvement in tensile strength compared with the neat NR. The findings of this study suggest that ultrasonically-synthesized palm CNF-ZnO nanocomposites could find potential applications in the biomedical field and in the development of high strength rubber composites.     

The changes of chemical composition of microencapsulated roselle (Hibiscus sabdariffa L.) seed oil by co-extrusion during accelerated storage

Roselle seed oil (RSO) is an underutilised seed oil, which is having beneficial properties to humans. Microencapsulation of vegetables and seed oil is an alternative to preserve these properties and deliver them to the human diet. In this study, microencapsulation of RSO was performed using co-extrusion technology and 1.5% w/w sodium alginate solution with 1.5% w/w high methoxyl pectin as the wall materials. Results showed that the microencapsulation efficiency was high (95.68 ± 1.95%) and the microencapsulation indeed preserved the content of unsaturated fatty acids, phytosterols, and tocopherols. During an accelerated storage condition at 65 °C for 24 days, most of these properties remained high for the first six storage days, including tocopherol which preserved high γ-tocopherol. Worth noting that the microencapsulated RSO (MRSO) was particularly effective in preserving the total unsaturated fatty acids (especially C18:1 and C18:2), even during the 24th day of storage. The total unsaturated fatty acids retained by MRSO were significantly (P < 0.05) higher (70 ± 0.4%) than the RSO (65.6 ± 1.6%). In short, microencapsulation was effective in preserving the RSO properties.     

Fibre Bragg grating compression-tuned over 110 nm

A fibre Bragg grating with a tuning range covering beyond the C- and L-bands has been realised, which represents the broadest tuning range reported of any Bragg grating. The device exhibits constant spectral response and polarisation mode dispersion within these bands.     

Controlled Growth of Conductive AlN Thin Films by Plasma-Assisted Reactive Evaporation

Metallurgical and Materials Transactions A - In this work, the growth of conductive AlN thin films by plasma-assisted reactive evaporation at different filament-to-substrate distances was presented...     

Silole‐Based Red Fluorescent Organic Dots for Bright Two‐Photon Fluorescence In vitro Cell and In vivo Blood Vessel Imaging

Robust luminescent dyes with efficient two‐photon fluorescence are highly desirable for biological imaging applications, but those suitable for organic dots fabrication are still rare because of aggregation‐caused quenching. In this work, a red fluorescent silole, 2,5‐bis[5‐(dimesitylboranyl)thiophen‐2‐yl]‐1‐methyl‐1,3,4‐triphenylsilole ((MesB)₂DTTPS), is synthesized and characterized. (MesB)₂DTTPS exhibits enhanced fluorescence efficiency in nanoaggregates, indicative of aggregation‐enhanced emission (AEE). The organic dots fabricated by encapsulating (MesB)₂DTTPS within lipid‐PEG show red fluorescence peaking at 598 nm and a high fluorescence quantum yield of 32%. Upon excitation at 820 nm, the dots show a large two‐photon absorption cross section of 3.43 × 10⁵ GM, which yields a two‐photon action cross section of 1.09 × 10⁵ GM. These (MesB)₂DTTPS dots show good biocompatibility and are successfully applied to one‐photon and two‐photon fluorescence imaging of MCF‐7 cells and two‐photon in vivo visualization of the blood vascular of mouse muscle in a high‐contrast and noninvasive manner. Moreover, the 3D blood vasculature located at the mouse ear skin with a depth of over 100 μm can also be visualized clearly, providing the spatiotemporal information about the whole blood vascular network.     

Poisson Model of Construction Incident Occurrence

Construction incidents are essentially random events because they have a probabilistic component that causes their occurrence to be indeterministic. Thus, as with most random events, one of the best ways to understand and analyze construction incidents is to apply statistical methods and tools. Consequently, this paper presents a statistical framework based on the modified loss causation model (MLCM). Even though the MLCM has been used for the framework, the approach can be readily adapted for other incident causation models. The MLCM is separated into two basic components: random and systematic. The random component is represented by a probability density function (PDF), which has parameters influenced by the systematic component of the MLCM, while the systematic component is represented by the situational variables and quality of the safety management system. In particular, this paper proposes that the PDF can be represented by the Poisson distribution. Besides being a convenient and simple distribution that can be easily used in applications, the Poisson distribution had been used in various industries to model random failures or incidents. The differences in contexts and the undesirable effects of adopting an unrepresentative distribution will require formal analysis to determine the suitability of the Poisson distribution in modeling the random component of construction incident occurrence. Incident records for 14 major projects were used in the analysis. Hypothesis testing using the chi-square goodness-of-fit and dispersion tests shows that the incident occurrences can be modeled as a Poisson process characterized by some mean arrival rate. The paper also presents some applications of the proposed Poisson model to improve construction safety management, focusing on two specific concepts: the Bayesian approach and the partitioned Poisson.     

Advances in optical path crossconnect systems using planar-lightwave circuit-switching technologies

This article highlights advances in NTT's optical path crossconnect systems that use planar-lightwave circuit switches. A photonic MPLS router that can handle up to 256 optical label switched paths is developed as one result of our R&D activities; mature OPXC technologies are adopted to create a practical OPXC system.