Nd3+ Doped Silicate Glass Photonic Crystal Fiber with Random Hole Distributions

The fabrication of one kind of large core area Nd3 doped silicate glass photonic crystal fiber, and demonstration of the fiber's waveguidence properties were reported. This fiber owns a random air hole distribution in the cladding. The measured minimum loss of this kind of fiber is 10 dB·m-1 at 660 nm. These fibers can sustain only a single mode at least over wavelength ranging from 660 nm to 980 nm.     

Evaluation of accuracy of measuring intraocular pressure by handheld non-contact applanation tonometer

PURPOSE: To evaluate the accuracy of measuring intraocular pressure by handheld non-contact applanation tonometer. METHOD: 58 patients' (113 eyes) intraocular pressure were measured by Keeler, non-contact tonometer and R 900 Goldmann applanation tonometer and the results of measurement of intraocular pressure by the two kinds of tonometers were compared. RESULT: The mean intraocular pressure measured by non-contact is 16.31 +/- 5.59 mmHg and 17.49 +/- 6.13 mmHg (1 mmHg = 0.1333 kPa) by Goldmann applanation tonometer, respectively. There was no statistical significance to be found (P > 0.05) between the two methods. By linear correlation and regression analysis, a positive correlation was found between the two methods (r = 0.8942, b = 0.8154). CONCLUSION: The handheld non-contact tonometer has the same accuracy and reliability of measurement of intraocular pressure comparing with Goldmann applanation tonometer, and it can be used in glaucoma clinic and screening.     

锆(Ⅳ)-3,5-diBr-PADAP-安替比林三元配合物的分光光度研究与应用

本文提出在安替比林存在下,以3,5-diBr-PADAP为显色剂,分光光度测定微量锆的新方法。在pH1～2的HCl介质中,锆(W)与试剂和安替比林形成配合比为1:1:1的红色三元配合物,最大吸收值在615nm波长处,摩尔吸光系数ε=1.35×10~5。锆(Ⅳ)量在0～25μg/25ml范围内,遵守比尔定律。方法简单、快速、准确。若采用钽试剂—苯萃取法分离共存离子,可适用于钽铌矿和合金中痕量锆的测定。     

Evolving Fault-Tolerant Neural Networks

In this paper, genetic algorithm is used to help improve the tolerance of feedforward neural networks against an open fault. The proposed method does not explicitly add any redundancy to the network, nor does it modify the training algorithm. Experiments show that it may profit the fault tolerance as well as the generalisation ability of neural networks.     

Optically tuned superconductive-dielectric resonators with whispering-gallery modes

An analytical method is presented for calculating the resonant frequency andQ-factor of a superconducting dielectric disk resonator operating in millimeter-wave regime with whispering-gallery mode. Resonant frequency shift due to the optical generation of quasi-particles in superconducting film is investigated as a function of photon flux. An optically tunable resonant frequency of about 500 MHz is estimated, and good agreement is found between numerical results and experimental ones.     

Determination of tablet coating distribution by deconvolution of uncoated and coated tablet weight distributions

PURPOSE: The purpose of this research is to obtain the tablet coating distribution from weight distributions of uncoated and coated tablets. METHODS: The method of deconvolution with digital smoothing was used to calculate the distribution of coating applied to a tablet population from separate random measurements of individual uncoated and coated tablets. RESULTS: It was demonstrated that the calculated coating weight distribution agrees well with the measured distribution. The effect of the smoothing factor on the solution is illustrated. CONCLUSIONS: This method can be used during development to facilitate process scale-up/optimization. In routine production, the method can assess the reproducibility and consistency of a coating process.     

Experimental Study on Energy Consumption of Combined Conventional and Dehumidification Drying

Conventional drying, dehumidification drying, and combined conventional-dehumidification drying of wood were experimentally studied in this article. The results showed that the energy consumption in the dehumidification drying is the least but its drying time is the longest. The energy consumption in the combined drying is more than that in the dehumidification drying but less than that in the conventional drying, and the drying time is half of that in the dehumidification drying. The advantages of the combined conventional and dehumidification drying are discussed from the experiments results.     

MEASUREMENT OF COEFFICIENTS FOB SIMULTANEOUS HEAT AND MASS TRANSFER IN FOOD PRODUCTS

Two experimental devices were designed and built to determine four coefficients K_T K_M D_M D (or δ_T = D_T / D_M occurring in simultaneous heat and mass transfer equations, where,K _T and D_M are thermal conductivity and moisture diffcusivity respectively, D_T ( or δ _T is temperature gradient Induced moisture migration coefficient and K_M is moisture gradient Induced heat transfer coefficient. Three food materials, i.e. potato, bread dough and bread, were tested. From this study, it was found that the value of 5 was higher for low density food materials, such as bread, than for high density materials, such as potato. The coefficient & measures moisture migration contribution due to temperature gradient within the material. The average values of δ _T for potato, bread dough and bread were 0.0014, 0.0059 and 0.0127 per °C, respectively. The contribution of temperature gradient to the overall moisture migration is negligible In high density materials. However, this contribution may be important in the moisture migratlon analysls for low density materials. The moisture gradient induced heat transfer coefficient % as found to be negligible for the materials tested in this study