异件共型的压铸模设计

阐述了把形状和主要壁厚差别很大的几种零件放在一个压铸模上同时成形的设计方法。     

不同添加剂对AgSnO2In2O3触头材料电性能的影响

采用内氧化法工艺制备了不含添加剂及分别含添加剂CuO或TeO2的3种AgSnO2In2O3触头材料。应用模拟继电器试验设备检测了这3种材料在AC230 V、25 A阻性负载条件下的电寿命、熔焊力、电弧能量、燃弧时间、质量侵蚀率等相关电性能参数,并对检测结果及试验后铆钉触头样品进行了分析。研究发现:与不含添加剂的AgSnO2In2O3材料相比,添加剂CuO对材料的电寿命影响不大,而添加剂TeO2明显提高了材料的电寿命;含添加剂的两种材料的熔焊力和电弧能量均有了不同程度的降低,但它们的质量侵蚀率却明显增加。     

Influence of pre-oxidation on the hot corrosion of Ti3SiC2 in the mixture of Na2SO4-NaCl melts

Polycrystalline Ti₃SiC₂ suffered from serious hot corrosion attack in the mixture of 75wt.%Na₂SO₄ + 25wt.%NaCl melts at 850 °C. In order to improve the hot corrosion resistance of this material, pre-oxidation treatment was conducted at 1200 °C in air for 2 h. A duplex oxide scale with an outer layer of TiO₂ and an inner layer of a mixture of TiO₂ and SiO₂ was formed during the pre-oxidation. Because the outer oxide layer of the pre-oxidation treated specimens could inhibit hot corrosion process, they exhibited good hot corrosion resistance in the mixture of 75wt.%Na₂SO₄ + 25wt.%NaCl melts at 850 °C for 50 h. However, during the hot corrosion the outer layer of TiO₂ would degrade gradually. Once the outer layer damaged, the hot corrosion rate increased sharply, the corrosion behavior was similar to Ti₃SiC₂ corroded under the same conditions. The microstructure and phase compositions of the hot corrosion samples were investigated by SEM/EDS and XRD.     

速动形状记忆合金元件设计原理

提出了评价速动双程形状记忆元件性能的主要参数,并说明了设计实用速动元件的原理和方法。     

静磁场对ZK60镁合金组织的影响

试验发现在镁合金的凝固过程中施加静态磁场能有效细化晶粒，减小晶界化合物的厚度，同时，出现了大量细小块状化合物，这有利于提高镁合金的成形性能。     

CLIPS在开发冲压模具选材专家系统中的应用

研究CLIPS在开发冲压模具选材专家系统中的应用问题,论述了借助CLIPS解决知识表示、模式匹配算法和不确定推理等实际问题的途径,以及支持专家系统的模具材料数据库结构.     

Study on the machinability of resulfurized composite free-cutting steels

The machinability of S, S-Ca, S-RE, and S-RE-Ca system resulfurized composite free-cutting steels were investigated, where RE is rare earths, mostly cerium. The experimental results showed that in the low cutting speed range (≤35 m/min), the S-RE system free-cutting steel had better machinability than the others and that the S-RE-Ca system free-cutting steel exhibited the best machinability at high cutting speeds. A protective layer capable of preventing diffusion wear was formed on the rake face of a P30 tool when S-RE-Ca system free-cutting steel was machined in the cutting speed range of 120 to 160 m/min.     

Investigation on gradient material fabrication with electron beam melting based on scanning track control

A new electron beam control system was developed in a general vacuum electron beam machine by assembling with industrial control computer, programmable logic control （PLC）, deflection coil, data acquisition card, power amplifier, etc. In this control system, scanning track and energy distribution of electron beam could be edited off-line, real-time adjusted and controlled on-line. Ti-Mo gradient material （GM） with high temperature resistant was fabricated using the technology of electron beam melting. The melting processes include three steps, such as preheating, melting, and homogenizing. The results show that the GM prepared by melting technology has fine appearance, and it has good integrated interface with the Ti alloy. Mo and Ti elements are gradually distributed in the inter.face of the gradient material. The microstructure close to the Ti alloy base metal is α ＋ β basket-waver grain, and the microstructure close to the GM is a single phase of β solid solution.     

超声波处理微污染水体技术研究

考察了用超声波降解水中低浓度三氯乙腈、氯代苦味碱、溴苯的动力学，并从工程角度分析了多种污染物共存、自然水体等复杂状态下的可行性。探讨了采用空气鼓泡、不控水温的操作方式。结果表明超声波可以较快地去除复杂水体中的多种有机污染物，氧化可在批式反应器与连续流反应器中进行，高流速可以提高反应器的空间与能量利用效率。     

饲料级磷酸氢钙标准样品的研制

简述了饲料级磷酸氢钙标准样品的研制过程，并对样品作了稳定性试验，对搅拌设备的搅拌均匀性和物料的均匀性进行了测定，并由国家认可实验室进行了定值数据的监测。通过对比实验证明了国家实验室之间的无差异性。实验数据表明了所测定的饲料级磷酸氢钙产品是稳定和均匀的，同时简要介绍标准样品的研制程序，为开发其他化工行业标准样品奠定了基础。