Illuminating Dark Plasmons of Silver Nanoantenna Rings to Enhance Exciton–Plasmon Interactions

The chemical growth of silver nanorings that possess singly twinned crystals and a circular cross section via a reductive reaction solution is reported. The wire and ring diameters of the synthesized nanorings are in the ranges 80–200 nm and 4.5–18.0 μm, respectively. By lighting up the multipolar dark plasmons with slanted illumination, the silver nanoring exhibits unique focused scattering and large local‐field enhancement. We also demonstrate strong exciton–plasmon interactions between a monolayer of CdSe/ZnS semiconductor quantum dots and a single silver antenna‐like nanoring (nanoantenna) at the “hot spots” located at the cross points of the incident plane and nanoring; the position of these spots are tunable by adjusting the incidence angle of illumination. The tunable plasmonic behavior of the silver nanorings could find applications as optical nanoantennae or plasmonic nanocavities.     

高硫原油生产清洁燃料组合工艺技术

通过九个加工方案的对比，指出对于新建的10Mt/a炼油厂，建议采用减压渣油加氢脱硫 重油催化裂化 加氢裂化加工方案，或溶剂脱沥青 加氢裂化 重油催化裂化方案；对于已有的炼油厂需进行加工高硫原油技术改造时，建议采用溶剂脱沥青 加氢裂化 重油催化裂化方案。     

3.33dtexDU1腈纶膨体毛条生产探讨

通过对3．33dtexDU1腈纶膨体毛条两种生产方案的对比,分析了原料和拉断机工艺对生产的影响,确立了3．33dtexDU1腈纶膨体毛条今后的生产方式。     

Cl‐Doped ZnO Nanowire Arrays on 3D Graphene Foam with Highly Efficient Field Emission and Photocatalytic Properties

An environmentally friendly, low‐cost, and large‐scale method is developed for fabrication of Cl‐doped ZnO nanowire arrays (NWAs) on 3D graphene foam (Cl‐ZnO NWAs/GF), and investigates its applications as a highly efficient field emitter and photocatalyst. The introduction of Cl‐dopant in ZnO increases free electrons in the conduction band of ZnO and also leads to the rough surface of ZnO NWAs, which greatly improves the field emission properties of the Cl‐ZnO NWAs/GF. The Cl‐ZnO NWAs/GF demonstrates a low turn‐on field (≈1.6 V μm⁻¹), a high field enhancement factor (≈12844), and excellent field emission stability. Also, the Cl‐ZnO NWAs/GF shows high photocatalytic efficiency under UV irradiation, enabling photodegradation of organic dyes such as RhB within ≈75 min, with excellent recyclability. The excellent photocatalytic performance of the Cl‐ZnO NWAs/GF originates from the highly efficient charge separation efficiency at the heterointerface of Cl‐ZnO and GF, as well as improved electron transport efficiency due to the doping of Cl. These results open up new possibilities of using Cl‐ZnO and graphene‐based hybrid nanostructures for various functional devices.     

嵌入式环境下关于移动性的研究

首先诠释在嵌入式环境下移动性的含义,分析并实现两种解决移动性的方案———Mobile IP(在IP层增加移动性)和Mobile SIP(在应用层增加移动性)。最后,对两种方案进行比较。     

Reducing the operation temperature of a solid oxide fuel cell using a conventional nickel-based cermet anode on dimethyl ether fuel through internal partial oxidation

Dimethyl ether (DME)-oxygen mixture as the fuel of an anode-supported SOFC with a conventional nickel-cermet anode for operating at reduced temperatures is systematically investigated. The results of the catalytic tests indicate that sintered Ni-YSZ has high activity for DME partial oxidation, and DME conversion exceeds 90% at temperatures higher than 700 °C. Maximum methane selectivity is reached at 700 °C. Cell performance is observed between 600 and 800 °C. Peak power densities of approximately 400 and 1400 mW cm⁻² at 600 and 800 °C, respectively, are reached for the cell operating on DME-O₂ mixture. These values are comparable to those obtained using hydrogen as a fuel, and cell performance is reasonably stable at 700 °C for a test period of 340 min. SEM results demonstrate that the cell maintains good geometric integrity without any delimitation of respective layer after the stability test, and EDX results show that carbon deposition occurrs only at the outer surface of the anode. O₂-TPO analysis shows that carbon deposition over the Ni-YSZ operating on DME is greatly suppressed in the presence of oxygen. Internal partial oxidation may be a practical way to achieve high cell performance at intermediate-temperatures for SOFCs operating on DME fuel.     

高分辨高灵敏度CCD图像传感器驱动时序设计

在分析面阵CCD图像传感器结构和驱动时序基础上,针对高分辨率高灵敏度ICX694ALG大面阵CCD图像传感器,研究其驱动时序发生器;以现场可编程门阵列(FPGA)作为硬件平台,通过Verilog HDL硬件描述语言对该驱动时序发生器进行了硬件描述,采用ISE软件进行功能仿真,并针对XILINX公司的可编程逻辑器件XC3S1000进行了硬件适配;仿真测试表明,FPGA驱动时序发生器能够满足高分辨高灵敏ICX694ALG大面阵CCD图像传感器驱动要求,达到了设计要求。     

多种节流形式的动静压轴承有限元—优化分析

在动静压轴承有限元分析的基础上对其不同的节流形式进行了优化计算 ,建立了有限元—优化迭代的计算模型 ,给出了浅腔相当节流比和相当节流液阻的计算方法 ,编制了计算机程序 ,得到了主要设计变量的优化结果     

基于学习分类器的多机器人路径规划收敛性研究

近年来,学习分类器LCS已广泛用于基于归纳学习的强化学习领域,但很少用于多机器人领域.提出了一种基于集成强化学习和遗传算法的学习分类器用于多机器人路径规划领域.由于遗传算法具有早熟收敛、局部最优解和占据较大的存储空间等缺陷,针对静态和动态环境因素对多机器人路径规划的不同影响,设计了在静态和动态环境下不同的适应度函数,在理论上推导并证明了信用分配算法的收敛性,为路径规划算法的收敛提供了理论保证.仿真实验结果也表明遗传算法和学习分类器结合用于多机器人的路径规划是有效的,遗传算法的早熟收敛、局部最优解、占据存储空间较大和收敛速度慢等难题得到很大改善,提高了多机器人发现安全路径的能力.所以LCS在机器人领域的应用前景是非常广阔的,是今后需要努力研究的方向.     

无线电引信贮存寿命预测方法研究

研究一种无线电引信贮存寿命预测方法,在不改变无线电引信失效机理的前提条件下,通过提高应力水平,在很短的时间内得到引信的失效数据,经过数字方法处理,预测出产品的贮存寿命。解决了无线电引信贮存寿命无法实际考核这一问题。