ZJ510L-B汽车用高强度热轧板的试制

珠钢150t电弧炉-LF(VD)-CSP(紧凑式带材生产)流程试生产的5～8mm ZJ510L-B(0．16C--1．22Mn)汽车用高强度热轧板的铁素体晶粒尺寸为6．0～9．2μm，带状组织为1．5～2．5级，强度极限σb562～610MPa，延伸率δ5 32．0％～38．6％。文中还分析和提出了带状组织的形成原因和改进措施。     

Microstructure and fatigue characteristics of direct chill cast and electromagnetic cast 2024 Al alloy ingots

The distinct advantages of the electromagnetic casting (EMC) process consist in the presence of stirring motions in the melt, which lead to significant grain size reduction in solidified ingot. Furthermore, surface and subsurface qualities are improved due to the absence of ingot mold. However, it is impossible to achieve the aforementioned advantages in conventional direct chill casting (DCC). In order to contrast the before and after heat treatments of the microstructural and mechanical characteristics of EMC and DCC 2024 aluminium alloys, optical microscopy, scanning electron microscopy, transmission electron microscopy (TEM), X-ray diffractions (XRD), differential scanning calorimetry (DSC), etc. were carried out. Compared with the DCC ingot, the EMC ingot has better mechanical properties not only in the ascast condition but also in the as-aged condition. The DSC curves show that the EMC specimens have high enthalpy, i.e., the thermal kinetic energy to form precipitates during the aging treatment process. Despite heat treatments applied to the DCC ingot, it fails to attain the same mechanical properties as the EMC ingot. Moreover, considering the expernsive scalping operation for DCC ingots, the EMC technique, which offers a lower manufacturing cost, is one of the best manufacturing methods used in obtaining the ingots of wrought aluminum alloys.     

基于SEP3203的高精度功耗测量仪器设计

重点阐述高精度功耗检测仪器及其软件的开发工作。本仪器以东南大学ASIC工程中心自主研发的基于ARM7TDMI的SEP3203嵌入式微处理嚣为核心处理器，以TI公司的高精度数模转换器ADS1210为转换器件实现模／数转换。采集器共设16个通道，通道与通道之间采用小体积固态继电器M211进行输入量隔离厦通道选通，并用TI公司的程控放大器PGA204对较小信号进行放大以匹配AD转换器的输入量程，有效提高了测量精度。本仪器通过RS485与PC机相连，电气隔离良好，具有较高的工作稳定性。     

Aroused problems in the deposition of diamond-like carbon films by using the liquid phase electrodeposition technique

Hydrogenated diamond-like carbon (DLC) films were prepared by using liquid phase electrodeposition technique. The effects of the applied potential and the carbon sources on the deposition process and film structures were studied. It has been found that the organic liquids with high dielectric constants, small viscosities and the methyl group bonding to the polar group are appropriate carbon sources. The increasing of potential improves the formation of sp³ carbon during the deposition process. In a high electric field, organic molecules are polarized and reacted on the surface of the electrode, turning out DLC and other products. It is believed that the reaction follows a polarization-reaction mechanism.     

室内设计中绿色设计的功效

绿色设计是一种将功能主义与可持续发展思想相结合的设计。文中就其形成的背景、设计原理及在室内设计领域中的应用进行一些探讨。     

纯镁对碳化硼颗粒的常压浸渗

本文研究了纯镁对不同致密度的碳化硼(B₄C)颗粒基片的常压浸渗性;讨论了镁液对B₄C颗粒聚集体常压浸渗的影响因素;提出了浸渗模型。研究表明,纯镁在氩气保护下,800～850℃温度范围保温30min即可浸渗B₄C颗粒聚集体。浸渗深度和宽度随加热温度升高和保温时间延长而增加;常压浸渗的B₄C_P/Mg复合材料具有很高的硬度,B₄C颗粒在基体中分布较均匀。     

Vortices in anisotropic type-II superconductors

We present a generalized variational model of an isolated vortex, valid in the anisotropic case when the external magnetic field is along one of the symmetry directions. We discuss the effects of the field anisotropy on the core and magnetic pinning of individual vortices.     

镶嵌在CaF2介质中纳米Cu团簇微观结构的研究

利用磁控溅射产生金属Ｃｕ团簇，同时蒸发ＣａＦ２介质，将Ｃｕ团簇包埋在ＣａＦ２介质中，团簇大小可通过改变溅射气压控制，用ＴＥＭ研究了嵌埋团簇的结构，分析结果表明：Ｃｕ团簇呈三角状多晶结构，团簇大小为１０￣７０ｎｍ，基质ＣａＦ２晶体也为多晶结构，Ｃｕ团簇的晶格常数在包埋状态下发生了膨胀，膨胀率大约在１６％左右。     

表面稳定模式铁电液晶的电光特性测试

采用一种改进的高分子膜摩擦定向法成功地实现了表面稳定模式铁电液晶的光学双稳态，对比度大于１４０，响应时间达１００微秒。     

各种状态的液体通过核孔膜的规律

介绍了液体通过核孔膜规律方面取得的新认识，包括：（１）纯净液体通过核孔膜的规律；（２）核孔膜测定液体粘滞系数的各种方法；（３）各种物质溶液浓度的核孔膜测定；（４）液相混合物快速分离和化学分离；（５）流体中固体微粒对核孔膜的堵塞及其公式；（６）用核孔膜滤除液中各各斩规律。