用于激光打靶实验数据采集处理和管理的微机局域网系统

介绍了一套基于微机局域网的ICF综合实验数据采集和处理系统，从基本物理实验需求的分析到系统软硬件的选择，物理测试节点的入网和实验数据的共享和管理等方面阐述了其整个建立过程，给出了实用系统的结构和其应用情况。     

Reynolds number-dependent permeability of wastewater sludge flocs

Most theoretical models assume constant permeability of wastewater sludge floc. This work shows that, at creeping flow limit with small intrafloc Reynolds number, the permeability of floc can not only be affected by floc structure, but also by the external flow condition. The three-dimensional structure of flocs using the fluorescence in situ hybridization (FISH) and the confocal laser scanning microscope (CLSM) was firstly probed. Then, the volumetric grid models for sludge flocs were constructed. We noted that the floc permeability could keep unchanged, increased, or decreased at increased Reynolds number (Re). Flow redistribution among channels of various sizes contributes to the noted Re-dependent permeability of flocs.     

Robustness analysis of responses of vibration control structures with uncertain parameters using interval algorithm

Variations in system parameters due to uncertainties may result in system performance deterioration. Uncertainties in modeling of structures are often considered to ensure that control system is robust with respect to response errors. Hence, the uncertain concept plays an important role in vibration control of the engineering structures. The paper discusses the robustness of responses of vibration control systems with the uncertain parameters. The vibration control problem of an uncertain system is approximated by a deterministic one. The uncertain parameters are described by interval variables. The uncertain state matrix is constructed directly using system physical parameters and avoided to use bounds in Euclidean norm. The feedback gain matrix is determined based on the deterministic systems, and then it is applied to the actual uncertain systems. A method to calculate the upper and lower bounds of responses of the closed-loop system with uncertain parameters is presented. The upper bounds of responses can be used to estimate the robustness of responses of the controlled system with uncertain parameters. Two numerical examples are given to illustrate the applications of the present approach.     

薄板坯连铸连轧工艺对铌微合金化高强度钢组织和性能的影响

首先建立薄板坯连铸连轧工艺的试验室模拟技术，并运用该模拟技术，研究薄板坯连铸连轧工艺(CSP)和传统板坯再加热工艺(TRP)两种工艺对铌微合金化高强度钢的显微组织和力学性能的影响。研究结果表明：CSP钢的晶粒细化效果不如TRP钢，两者的平均铁素体晶粒尺寸分别为8．17μm和6．30μm。在CSP试验钢板中铌的析出量较大，特别是在铁素体中细小颗粒的铌的析出物较多，沉淀强化效果较强。CSP试验钢的σ0.5和σb分别较TRP工艺低约40MPa和约25MPa，同时其低温冲击韧性较好，FATT温度较低。     

Formation and retention of local melted films in AZ91 friction stir spot welds

The formation of local melted films during friction stir spot welding of as-cast AZ91D and thixomolded AZ91 material is investigated. The average temperatures close to the tip of the rotating pin vary from 438 to 454 °C during the dwell period in friction stir spot welding. These measured temperature values are higher than the melting temperature of α-Mg + Mg₁₇Al₁₂ eutectic (437 °C). It is suggested that the temperature in the stir zone during the dwell period is determined by the relative proportions of α-Mg and (α-Mg + Mg₁₇Al₁₂) eutectic material, which are incorporated during friction stir spot welding. Based on the stir zone temperature measurements and a detailed examination of material located at the root of the pin thread it is suggested that material is moved downwards via the pin thread and into the stir zone during the dwell period in friction stir spot welding. Evidence of local melted film formation is observed in the stir zone of AZ91 spot welds. It is suggested that melted films are retained since their dissolution rate is much slower in the high temperature stir zone than it is when melted films is formed in the stir zone during Al 7075-T6 friction stir spot welding. The spontaneous melting temperature, solute diffusion rate and the thermodynamic driving force for droplet dissolution are much higher during Al 7075-T6 friction stir spot welding.     

合成2,4-二叔丁基苯酚工业试验

以离子交换树脂为催化剂，苯酚和甲基叔丁基醚为原料合成2，4-二叔丁基苯酚(简称2，4酚)，合成产物经过滤再经间歇真空精馏精制提纯，得到高纯度的2，4酚成品。成品精馏后釜中残液在酸性白土催化剂的作用下通过歧化反应生成对叔丁基苯酚，再经精馏提纯得到成品对叔丁基苯酚。通过工艺优化，使2，4酚、对叔丁基苯酚形成联产生产工艺，降低了生产原料消耗和成本。     

表冷器设计计算的一种新方法

本文从分析盘管内、外侧换热系数着手，提出了表冷器一种新的热工计算方法。     

吉林闹枝金矿床黄铁矿的标型特征研究

从成因矿物学及找矿矿物学的观点出发，系统地研究了闹枝金矿床黄铁矿的形态、粒度、化学成分、热电性、硫同位素方面的标型特征，为矿床的成因研究和深部远景评价提供了矿物学依据。     

An alternative method to compute the component fractions in the geometrical optical model: visual computing method

A method called visual computing was used to solve angular four-components' proportions and directional vegetation cover fraction for discrete canopies and continuous row-planted plants. It proved effective to predict the angular characteristics on pixel scale. The method could be an alternative way to a classical solution of geometrical optical models. A visual computing method would be effective especially when the canopies' spatial distribution and shapes were irregular and could not be described statistically.     

脉冲电镀最佳参数之探索和优化

本文利用正交实验法对脉冲电镀各控制参数进行试验,对影响分散能力、镀层可靠性及外观质量的各种因素进行探讨,寻找影响外观质量的显著因子并加以控制,同时进一步优化脉冲电镀的工艺参数。