The critical pressure and impeding pressure of Al evaporation during induction skull melting processing of TiAl

In this article, two key pressures, the critical pressure P _crit and the impeding pressure P _impe of elemental evaporation, are defined and studied based on the calculation relationship between the evaporation loss rate N _m and the chamber pressure P during melting of titanium-aluminum alloys. When the chamber pressure is below P _crit or above P _impe, N _m tends to the maximum or the minimum value and remains almost unchanged. However, if P _crit<P<P _impe, with the increase of the chamber pressure, N _m declines sharply. A method has been put forward to calculate P _crit and P _impe of Al evaporation in a Ti-XAl (at pct) (X=25 to 50) melt. The calculation result shows that P _crit or P _impe is a second-order function of the molar percentage of Al and the melt temperature.     

新增探明储量的经济可采储量计算方法

提出了新增探明储量有无经济可采储量的判别方法。在此基础上，通过对立已开发油田技术可采储量经济转化率与油藏空气渗透率的相关关系式和图版，根据储层的空气渗透率，计算新增探明储量的经济转化率和经济可采储量。该方法参数易取，计算简便，对于快速、准确计算新增探明储量的经济可采储量具有重要意义。     

调谐质量阻尼器参数设计中的两个问题

本文以单自由度系统安装一个调谐质量阻尼器（简称TMD）为例，对抗风和抗震两类不同激励工况下TMD的参数设计问题进行了理论研究与对比分析。通过给出相对误差系数的概念，定量评价了不同的参数方法对TMD减振性能的影响程度。本文的研究为TMD的参数设计提供了理论指导。     

建立水利工程管理运行新机制的思考

水利工程管理体制改革，是党中央、国务院根据我国经济和社会可持续发展需要，针对我国水利工作存在的突出问题做出的一项重大决策，通过改革，初步建立了职能清晰、权责明确、管理科学、经营规范、管养分离的新的水利工程管理体制。从根本上改变了过去长期形成的水利工程管理体制不顺、机制不活、经费不足、工程失修、安全不保的局面。     

用于激光打靶实验数据采集处理和管理的微机局域网系统

介绍了一套基于微机局域网的ICF综合实验数据采集和处理系统，从基本物理实验需求的分析到系统软硬件的选择，物理测试节点的入网和实验数据的共享和管理等方面阐述了其整个建立过程，给出了实用系统的结构和其应用情况。     

Reynolds number-dependent permeability of wastewater sludge flocs

Most theoretical models assume constant permeability of wastewater sludge floc. This work shows that, at creeping flow limit with small intrafloc Reynolds number, the permeability of floc can not only be affected by floc structure, but also by the external flow condition. The three-dimensional structure of flocs using the fluorescence in situ hybridization (FISH) and the confocal laser scanning microscope (CLSM) was firstly probed. Then, the volumetric grid models for sludge flocs were constructed. We noted that the floc permeability could keep unchanged, increased, or decreased at increased Reynolds number (Re). Flow redistribution among channels of various sizes contributes to the noted Re-dependent permeability of flocs.     

Robustness analysis of responses of vibration control structures with uncertain parameters using interval algorithm

Variations in system parameters due to uncertainties may result in system performance deterioration. Uncertainties in modeling of structures are often considered to ensure that control system is robust with respect to response errors. Hence, the uncertain concept plays an important role in vibration control of the engineering structures. The paper discusses the robustness of responses of vibration control systems with the uncertain parameters. The vibration control problem of an uncertain system is approximated by a deterministic one. The uncertain parameters are described by interval variables. The uncertain state matrix is constructed directly using system physical parameters and avoided to use bounds in Euclidean norm. The feedback gain matrix is determined based on the deterministic systems, and then it is applied to the actual uncertain systems. A method to calculate the upper and lower bounds of responses of the closed-loop system with uncertain parameters is presented. The upper bounds of responses can be used to estimate the robustness of responses of the controlled system with uncertain parameters. Two numerical examples are given to illustrate the applications of the present approach.     

薄板坯连铸连轧工艺对铌微合金化高强度钢组织和性能的影响

首先建立薄板坯连铸连轧工艺的试验室模拟技术，并运用该模拟技术，研究薄板坯连铸连轧工艺(CSP)和传统板坯再加热工艺(TRP)两种工艺对铌微合金化高强度钢的显微组织和力学性能的影响。研究结果表明：CSP钢的晶粒细化效果不如TRP钢，两者的平均铁素体晶粒尺寸分别为8．17μm和6．30μm。在CSP试验钢板中铌的析出量较大，特别是在铁素体中细小颗粒的铌的析出物较多，沉淀强化效果较强。CSP试验钢的σ0.5和σb分别较TRP工艺低约40MPa和约25MPa，同时其低温冲击韧性较好，FATT温度较低。     

Formation and retention of local melted films in AZ91 friction stir spot welds

The formation of local melted films during friction stir spot welding of as-cast AZ91D and thixomolded AZ91 material is investigated. The average temperatures close to the tip of the rotating pin vary from 438 to 454 °C during the dwell period in friction stir spot welding. These measured temperature values are higher than the melting temperature of α-Mg + Mg₁₇Al₁₂ eutectic (437 °C). It is suggested that the temperature in the stir zone during the dwell period is determined by the relative proportions of α-Mg and (α-Mg + Mg₁₇Al₁₂) eutectic material, which are incorporated during friction stir spot welding. Based on the stir zone temperature measurements and a detailed examination of material located at the root of the pin thread it is suggested that material is moved downwards via the pin thread and into the stir zone during the dwell period in friction stir spot welding. Evidence of local melted film formation is observed in the stir zone of AZ91 spot welds. It is suggested that melted films are retained since their dissolution rate is much slower in the high temperature stir zone than it is when melted films is formed in the stir zone during Al 7075-T6 friction stir spot welding. The spontaneous melting temperature, solute diffusion rate and the thermodynamic driving force for droplet dissolution are much higher during Al 7075-T6 friction stir spot welding.     

合成2,4-二叔丁基苯酚工业试验

以离子交换树脂为催化剂，苯酚和甲基叔丁基醚为原料合成2，4-二叔丁基苯酚(简称2，4酚)，合成产物经过滤再经间歇真空精馏精制提纯，得到高纯度的2，4酚成品。成品精馏后釜中残液在酸性白土催化剂的作用下通过歧化反应生成对叔丁基苯酚，再经精馏提纯得到成品对叔丁基苯酚。通过工艺优化，使2，4酚、对叔丁基苯酚形成联产生产工艺，降低了生产原料消耗和成本。