Phase Behavior and Mechanical Properties of Siloxane-Urethane Copolymer

Two series of siloxane-urethane copolymers were prepared from polydimethylsiloxane (PDMS) with a molecular weight of 1000 or 1800 which was used as a soft segment, 4,4′-diphenylmethane diisocyanate (MDI) and 1,4-butanediol (1,4-BD). Differential scanning calorimetry (DSC) demonstrated that the position (T_gs) and breadth (ΔB) of soft-segment glass transition of copolymers remained constant as the hard-segment content increased. Heat capacities at soft-segment glass transition of the copolymer (ΔCp) were 0.195∼0.411 J/g^○C and heat capacities of pure PDMS (ΔCp₀) were 0.571∼0.647 J/g^○C, leading to the various ΔCp/ΔCp₀ ratios. The ΔCp/ΔCp₀ ratios decreased as the increasing of hard-segment content, showing poor phase separation. The FTIR spectrum confirmed the occurrence of hydrogen bonding in ether end-group of pure PDMS. The ether group of the soft segment led to interfacial mixing between soft and hard segments. The tan δ of the soft segment determined by dynamic mechanical testing (DMA) also identified the mixing of soft and hard segments. The mechanical properties of the copolymer were directly related to either the soft and hard segment contents or the chain lengths of soft and hard segments. The hard segment that reinforced the soft segment and interfacial thickness between soft and hard segment dominated the mechanical properties.     

Optimal reaction conditions for the minimization of energy consumption and by‐product formation in a poly(ethylene terephthalate) process

We determined the optimal reaction conditions to minimize the energy cost and the quantities of by‐products for a poly(ethylene terephthalate) process by using the iterative dynamic programming (IDP) algorithm. Here, we employed a sequence of three reactor models: the semibatch transesterification reactor model, the semibatch prepolymerization reactor model, and the rotating‐disc‐type polycondensation reactor model. We selectively chose or developed the reactor models by incorporating experimentally verified kinetic models reported in the literature. We established the model for the entire reactor system by connecting the three reactor models in series and by resolving some joint problems arising when different types of reactor models were interconnected. On the basis of the simulation results of the reactor system, we scrutinized the cause and effect between the reaction conditions and the final quality of the polymer product. Here, we set up the optimization strategy by using IDP on the basis of the integrated reactor model, and the process variables with significant influence on the properties of polymer were selected as control variables with the help of a simulation study. With this method, we could refine the reaction conditions at the end of each iteration step by contracting the spectra of control regions, and the iteration process finally stopped when the profile of the optimal trajectory converged. We also took the constraints on the control variables into account to guarantee polymer quality and to suppress side reactions. Constituting six different strategies by setting weighting vectors differently, we examined the differences in optimal trajectories, the trend of optimality, and the quality of the final polymer product. For each of the strategies, we conducted the optimization to examine whether the number‐average degree of polymerization approached the desired value. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 993–1008, 2002     

Anisotropically ordered liquid crystalline epoxy network on carbon fiber surface

Summary Anisotropic orientation of liquid crystalline epoxy(LCE) resin on carbon fiber(CF) surface was investigated and it was correlated with curing behavior and thermomechanical properties of LCE. Anisotropic orientation of a LCE resin was spontaneously induced on CF surface along a long molecular axis of CF during curing and the anisotropic orientation was maintained after curing. Curing of LCE was accelerated by alignment of LCE on CF and anisotropic orientation of LCE enhanced dynamic modulus of CF reinforced LCE composites.     

Universal yield stress function for biocompatible chitosan based-electrorheological fluid: Effect of particle concentration

Electrorheological (ER) response of biocompatible particles suspended in an insulating silicone oil, was investigated under several different applied external electric field strengths. Chitosan, a biodegradable polysaccharide, was used as anhydrous ER materials. The effect of particle volume concentration on their ER response was examined by focusing on the measurement for rheological and electrical properties. The yield stress of chitosan suspended in silicone oil system as a function of applied electric field strength showed different value of slopes for different particle concentrations, however, all data points collapse onto a universal scaling function.     

Morphology and mechanical properties of liquid crystalline copolyester and poly(ethylene 2,6-naphthalate) blends

Blends of poly(ethylene 2,6-naphthalate) (PEN) and a liquid crystalline copolyester (LCP), poly(benzoate-naphthoate), were prepared in a twin-screw extruder. Specimens for mechanical testing were prepared by injection molding. The morphology and mechanical properties were investigated by scanning electron microscopy (SEM) and an Instron tensile tester. SEM studies revealed that finely dispersed spherical domains of the liquid crystalline polymer (LCP) were formed in the PEN matrix, and the inclusions were deformed into fibrils from the spherical droplets with increasing LCP content. The morphology of the blends was found to be affected by their composition and a distinct skin-core morphology was found to develop in the injection molded samples of these blends. Mechanical properties were improved with increasing LCP content, and synergistic effects have been observed at 70 wt% LCP content whereas the elongation at break was found to be reduced drastically above 10 wt% of LCP content. This is a characteristic typical of chopped-fiber-filled composites. The improvement in mechanical properties is likely due to the reinforcement of the PEN matrix by the fibrous LCP phase as observed by scanning electron microscopy. The tensile and modulus mechanical behavior of the LCP/PEN blends was very similar to those of the polymeric composite, and the tensile strength and flexural modulus of the LCP/PEN 70/30 blend were two times the value of PEN homopolymer and exceeded those of pure LCP, suggesting LCP acts as a reinforcing agent in the blends.     

Enhancement of combustion efficiency with mixing ratio during fluidized bed combustion of anthracite and bituminous blended coal

In order to investigate the effect of mixing ratio of bituminous coal to blended coal on the enhancement of combustion efficiency, combustion experiments of blended coal with anthracite and bituminous are done in a laboratory scale fluidized bed combustor (10.8 cm ID and 170 cm height). The gross heating values of anthracite and bituminous coal used in this study are 2,810 cal/g and 6,572 cal/g, respectively. Experimental parameters are fuel feed rate, superficial gas velocity and mixing ratio of bituminous coal to blended coal. The combustion efficiency increases with the mixing ratio of bituminous coal due to the lower unburned carbon losses and higher burning velocity of bituminous coal. The rate of combustion in the combustor was increased with mixing ratio resulted from a higher burning velocity of bituminous coal. The measured combustion efficiency experimentally is about 3.5-12.4% higher than that of the calculated value based on the individual combustion of anthracite and bituminous coal under the same operating conditions. The optimum mixing ratio (MR) of bituminous coal determined is around 0.75 in this study. This paper is dedicated to Professor Dong Sup Doh on the occasion of his retirement from Korea University.     

Organic Nanoparticles with Polypropyleneoxide Chains as Support for Metallocene Catalysts: Ethylene Homopolymerization and Ethylene/α-olefin Copolymerization

Summary Novel organic nanoparticles functionalized with nucleophilic polypropyleneoxide (PPO) chains on their surfaces for supporting metallocene catalysts in heterogeneous olefin polymerization are presented. The nanoparticles (60–100 nm) were obtained by miniemulsion polymerization of styrene, divinylbenzene and PPO functionalized styrene. It is demonstrated that Me₂Si(2MeBenzlnd)₂ZrCl₂/MAO supported on these nanoparticles is suitable for the homopolymerization of ethylene, resulting in excellent product morphologies and high activities. lt is shown that by varying the MAO/Zr ratios and Zr concentrations the activities and productivities of the catalysts as well as the qualities of the polyethylene products can be tuned. These new supported catalysts are also suitable for the copolymerization of ethylene with several comonomers (1-hexene, 1-octene, 1-decene or norbornene). As the obtained product properties like crystallinity, melting temperature or bulk density match the results of silica supported systems, these organic nanoparticles can be considered as alternative carriers in comparison to the established inorganic ones.     

Scalable Realistic Rendering with Many‐Light Methods

Recent years have seen increasing attention and significant progress in many‐light rendering, a class of methods for efficient computation of global illumination. The many‐light formulation offers a unified mathematical framework for the problem reducing the full lighting transport simulation to the calculation of the direct illumination from many virtual light sources. These methods are unrivaled in their scalability: they are able to produce plausible images in a fraction of a second but also converge to the full solution over time. In this state‐of‐the‐art report, we give an easy‐to‐follow, introductory tutorial of the many‐light theory; provide a comprehensive, unified survey of the topic with a comparison of the main algorithms; discuss limitations regarding materials and light transport phenomena and present a vision to motivate and guide future research. We will cover both the fundamental concepts as well as improvements, extensions and applications of many‐light rendering.     

Pathline glyphs

Visualization of pathlines is common and highly relevant for the analysis of unsteady flow. However, pathlines can intersect, leading to visual clutter and perceptual issues. This makes it intrinsically difficult to provide expressive visualizations of the entire domain by an arrangement of multiple pathlines, in contrast to well‐established streamline placement techniques. We present an approach to reduce these problems. It is inspired by glyph‐based visualization and small multiples: we partition the domain into cells, each corresponding to a downscaled version of the entire domain. Inside these cells, a single downscaled pathline is drawn. On the overview scale, our pathline glyphs lead to emergent visual patterns that provide insight into time‐dependent flow behavior. Zooming‐in allows us to analyze individual pathlines in detail and compare neighboring lines. The overall approach is complemented with a context‐preserving zoom lens and interactive pathline‐based exploration. While we primarily target the visualization of 2D flow, we also address the extension to 3D. Our evaluation includes several examples, comparison to other flow visualization techniques, and a user study with domain experts.     

An analysis of muscles from ultrasound image using morphological information of fascia and thoracic vertebra

In this paper, we propose a new fully computerized image analysis method for measuring the thickness of muscles from ultrasound image obtained by muscle endurance test using morphological information of fascia and thoracic vertebra. Firstly, we divide the image into lumbar region and thoracolumbar region by the difference of density in image for measuring the thickness of muscles. In lumbar region, we notice that the intensity of fascia is relatively higher than other parts. Thus, we measure the thickness of muscles surrounding the fascia area. In the process, we apply median filter to candidate fascia areas for extracting candidate muscle layers between fascias. Then, the thickness of muscles we measure is that of the third layer. In thoracolumbar region, we apply region expansion method for classifying the region into subcutaneous fat part and part including thoracic vertebra. Then, we apply counting method and evolutionary computation search model to find the measuring location that is in between subcutaneous fat area and thoracic vertebra. In experiment, the proposed method is effective in measuring the thickness of muscles and avoids failures of previous studies. The performance of this approach is sufficiently comparable to that of medical experts.