An efficient and direct method for out-of-plane buckling analysis of Y-braced steel frames

Dimensionless design-oriented charts are introduced for customising a new and efficient method of computing the out-of-plane critical buckling load of Y-braced steel frame systems. These charts are derived from extensive parametric studies on the basis of an “exact solution”, within the limits of the Eulerian theory, stability analysis, using a wide array of geometric characteristics of practical interest. Demonstrated with numerical examples, these calculations are shown to yield, in a very efficient way, accurate critical load values of these systems. The charts can be used for practical design of Y-brace elements.     

Improvement of Glass Transition and Flowability of Reduced-Fat Coffee Creamer: Effect of Fat Replacer and Fluidized Bed Drying

This study was conducted to investigate the effects of inulin (0, 2.5, 5, and 7.5 %), maltodextrin (0, 15, 20, and 25 %), and different drying processes (one- and two-stage drying) on the morphology and physicochemical properties of regular and instant reduced-fat creamers. The present study showed that the drum-dried creamer containing 0 % maltodextrin and 0 % inulin was fully sticky powder with dark brown color. It was found that the maximum increase in maltodextrin (from 0 to 25 %) and inulin (from 0 to 7.5 %) resulted in the creamer with the highest glass transition temperature and the lowest stickiness among all formulated creamers. The application of two-stage drying involving fluidized bed drying resulted in further improvement of the glass transition temperature and stickiness of the reduced fat instant creamer. The instant creamers obtained from two-stage drying had considerably higher glass transition temperature and lower bulk density than the regular creamers from one-stage drying. Such improvement could be due to the reduction of bulk density induced by fluidized bed drying. This might be because of higher porosity of the creamer particles after agglomeration. The current study revealed that the addition of high amounts of inulin and maltodextrin also played a significant role in the reduction of bulk density and further improvement of glass transition temperature (T_g) and solubility of the reduced fat creamer. The instant reduced fat creamer containing 25 % maltodextrin and 7.5 % inulin had the most desirable characteristics among all formulated creamers.     

Performance evaluation of open-cycle solar regenerator using artificial neural network technique

Theoretical investigation on the performance of lithium chloride (LiCl) absorption cooling system using an artificial neural network (ANN) model is presented. Tabulated data from the literature are used to construct the ANN model. Solar collector desiccant/regenerator is applied to re-concentrate the working solution. Using the proposed model, the effect of system design parameters; namely regenerator length, and air flow rate on the performance of the system is demonstrated. The variation of the thermo-physical parameters along the regenerator length is highlighted.     

Kinetic Model for Invertase‐Induced Sucrose Hydrolysis: Initial Time Lag

The kinetics of sucrose hydrolysis by invertase was studied in order to find a comprehensive model for the reaction pathway and mechanism. First, three common models of Michaelis‐Menten (MM), substrate inhibition (S²), and substrate clusters' inhibition (S³(I)) were investigated. The third model was found to better predict the initial sucrose concentration. Then, the S³(I) model was modified to cover the remaining pathway (S³(II)). Finally, a new comprehensive model (S³(III)) was evaluated, which in addition to what is considered in the two previously mentioned models (S³(I) and S³(II)) also involved the initial time lag. The model predictions showed an excellent agreement with the experimental data. The mean absolute error for the MM model is significantly reduced for the S³(III) model.     

An Application of Computer‐Aided Molecular Design (CAMD) Using the Signature Molecular Descriptor–Part 2. Evaluating Newly Identified Surface Tension‐Reducing Substances for Potential Use as Shrinkage‐Reducing Admixtures

In this study, the use of computer‐aided molecular design (CAMD) is validated as a tool for enabling the discovery of new shrinkage‐reducing compounds for possible use in portland cement composites and is framed as one of many multiscale modeling tools in a broad hierarchy of possibilities. Twelve additives were tested for their ability to inhibit shrinkage in Type I ordinary portland cement under both autogenous and drying conditions. The 12 additives included two commercial shrinkage‐reducing admixtures (SRAs), two active ingredients of a commercial admixture [one of which was used to establish the quantitative structure–property relationships (QSPR)], two additional classified as potential SRA compounds based on the patent literature, four newly identified compounds predicted by using CAMD and an inverse quantitative structure–property relationship (I‐QSPR), and two other compounds use to establish the QSPR relationship. The newly identified I‐QSPR compounds were targeted for their ability to reduce the surface tension of water, a primary consideration for shrinkage‐reducing activity. Results for both drying shrinkage and autogenous shrinkage indicate that the designed compounds perform similar to commercial admixtures, yet have different chemical functionalities. Hydration data and set measurements were also considered since selection of new SRAs is a multiparameter problem with many constraints. Thus, these newly identified shrinkage‐reducing compounds can potentially provide additional options for use in portland cement concrete applications.     

Control of Superelastic Behavior of NiTi Wires Aided by Thermomechanical Treatment with Reference to Three-Point Bending

The aim of this study is to investigate the effect of thermomechanical treatment on the superelastic behavior of a Ti-50.5 at.%Ni wire in terms of loading/unloading plateau, mechanical hysteresis, and permanent set to optimize these parameters for orthodontic applications. A new three-point bending fixture, oral cavity configuration three-point bending (OCTPB) test, was utilized to determine the superelastic property in clinical condition, and therefore, the tests were carried out at 37 °C. The results indicate that the thermomechanical treatment is crucial for thermal transformation and mechanically induced transformation characteristics of the wire. Annealing of thermomechanically treated specimens at 300 and 400 °C for 1/2 and 1 h leads to good superelasticity for orthodontic applications. However, the best superelasticity at body temperature is obtained after annealing at 300 °C for 1/2 h with regard to low and constant unloading force and minimum permanent set.     

Micromechanics of spatially uniform heterogeneous media: A critical review and emerging approaches

Outside of the classical microstructural detail-free estimates of effective moduli, micromechanical analyses of macroscopically uniform heterogeneous media may be grouped into two categories based on different geometric representations of material microstructure. Analysis of periodic materials is based on the repeating unit cell (RUC) concept and the associated periodic boundary conditions. This contrasts with analysis of statistically homogeneous materials based on the representative volume element (RVE) concept and the associated homogeneous boundary conditions. In this paper, using the above classification framework we provide a critical review of the various micromechanical approaches that had evolved along different paths, and outline recent emerging trends. We begin with the basic framework for the solution of micromechanics problems independent of microstructural representation, and then clarify the often confused RVE and RUC concepts. Next, we describe classical models, including the available RVE-based models, and critically examine their limitations. This is followed by discussion of models based on the concept of microstructural periodicity. In the final part, two recent unit cell-based models, which continue to evolve, are outlined. First, a homogenization technique called finite-volume direct averaging micromechanics theory is presented as a viable and easily implemented alternative to the mainstream finite-element based asymptotic homogenization of unit cells. The recent incorporation of parametric mapping into this approach has made it competitive with the finite-element method. Then, the latest work based on locally-exact solutions of unit cell problems is described. In this approach, the interior unit cell problem is solved exactly using the elasticity approach. The exterior problem is tackled with a new variational principle that successfully overcomes the non-separable nature of the overall unit cell problem.     

Rheological properties of biopolymers drilling fluids

Drilling muds are complex fluids, generally used to clean the well, maintain hole integrity, transport the rock cuttings, lubricate the drill bit and control formation pressures. Two basic types of drilling fluids are used, water based muds (WBM) and oil based muds (OBM). OBM are very effective but polluting, and environmental regulations continue to restrict the use of oil based muds in many areas of the world. In order to reduce the mud toxicity, we developed water based mud systems using two biopolymers, which are xanthan gum and scleroglucan, generally proposed for high permeability reservoirs or for complex geometries such as horizontal wells. In this study, we evaluated the rheological behaviour of different samples and we determined the effect of components such as clay, calcium carbonate and potassium chloride. This formulations exhibit non-Newtonian rheological behaviour which can be described well by the tree parameter in Herschel–Bulkley rheological model.     

Spontaneous Formation of Liquid Crystals in Ultralarge Graphene Oxide Dispersions

A novel process is developed to synthesize graphene oxide sheets with an ultralarge size based on a solution‐phase method involving pre‐exfoliation of graphite flakes. Spontaneous formation of lyotropic nematic liquid crystals is identified upon the addition of the ultralarge graphene oxide sheets in water above a critical concentration of about 0.1 wt%. It is the lowest filler content ever reported for the formation of liquid crystals from any colloid, arising mainly from the ultrahigh aspect ratio of the graphene oxide sheets of over 30 000. It is proposed that the self‐assembled brick‐like graphene oxide nanostructure can be applied in many areas, such as energy‐storage devices and nanocomposites with a high degree of orientation.     

Study the flashover voltage for outdoor polymer insulators under desert climatic conditions

This work presents a study of flashover voltage for outdoor polyester and composite insulators under some desert climatic conditions. Cylindrical polyester composite samples have been prepared after incorporated with different concentrations of inorganic fillers e.g., alumina trihydrate [ATH], boric acid [H₃BO₃] and magnesium hydroxide [Mg(OH)₂] to improve the electrical, mechanical and thermal properties in addition to maximize the surface flashover voltage and decrease the tracking phenomena.Results showed that flashover voltage reaches to 38 kV for samples without filler and 47 kV for samples containing 50% of ATH filler in dry condition. A comparison between inorganic fillers under various environmental conditions showed higher flashover voltage values for samples containing ATH filler than that of samples containing H₃BO₃ and Mg(OH)₂ fillers at all filler concentrations. Flashover voltage increases 24% by adding ATH filler for polyester samples under sandstorm conditions. Also, in this study, the effects of sandstorm, ultra violet (UV) radiation, mechanical strength (compressive and tensile strengths) and thermal performance with respect to surface of the sample under test have been investigated in detail.