Rheological properties of mixtures of molten polymer and fluorocarbon blowing agent. I. Mixtures of low-density polyethylene and fluorocarbon blowing agent

The viscosities of mixtures of low-density polyethylene and fluorocarbon blowing agent were determined from the measurement of wall normal stress along the longitudinal axis of a capillary die. For the study, three different grades of commercial high-pressure low-density polyethylene were used, together with the following fluorocarbon blowing agents, dichlorodifluoromethane (FC-12), dichlorotetrafluoroethane (FC-114), and blends of FC-12 and FC-114. In the experiment, blowing agent concentration and melt temperature were varied for each combination of polymer and blowing agent employed. Analysis of the experimental data has led to a correlation between the viscosity reduction factor (VRF) and the blowing agent concentration, in which VRF is defined as the ratio of the viscosity of polymer-blowing agent mixture to that of the polymer alone. It was found that the correlation obtained is independent of shear rate and temperature and dependent upon only the type of fluorocarbon blowing agent. The practical significance of the correlation is discussed. We have shown that the entrance pressure drop obtained in the absence of phase separation in the entrance region may be used as a measure of the elastic properties of mixtures of fluorocarbon blowing agent and low-density polyethylene resin.     

Guerbet十四醇的合成与表征

以正庚醇为原料 ,通过Guerbet反应合成Guerbet十四醇 (2 戊基壬醇 ,C14 GA)。用IR、NMR和元素分析测定了C14 GA的结构 ,并研究了反应温度和用料比对其产率的影响。实验结果如下 :(1)在较优化的反应条件下 (正庚醇的总加入量为 1mol,在实验过程中 ,先加入 1/ 3mol庚醇和 1/ 4mol的KOH ,在 16 0℃下反应 2h ,然后再加入剩下的 2 / 3mol庚醇和 4g 5 %Pd -C催化剂 ,在 15 5℃下反应 6h)合成产物 ,其产率可达到 5 4 2 0 % ;(2 )所合成的产物与试图要得到的Guerbet十四醇 (2 戊基壬醇 ,C14 GA)含有相同的基团 (2×—CH3、10×—CH2 —、1×CH、1×—CH2 —O—和 1×—OH) ,而且 ,所合成的产物中 ,w (C) =79 0 6 % ,w (H ) =13 6 2 % ,与从Guerbet十四醇分子式计算的理论值w(C) =78 5 0 % ,w (H) =14 0 1%基本一致。可见所合成的产物正是Guerbet十四醇 (C14 GA)     

Industrial TiO2 based nacreous pigments as functional building materials: Photocatalytic removal of NO

In this paper, the photocatalytic activity of industrial titanium dioxide (TiO₂) based nacreous pigments was researched as functional building materials for photocatalytic NO remove. Three industrial TiO₂ based nacreous pigments were selected to estimate the photocatalytic activity for NO remove. This study is a good proof that pearlescent pigments can eliminate NO, and its performance is positively correlated with its titanium dioxide content. And this research will widen the application of nacreous pigments in functional building materials, and provide a new way to eliminate in door nitric oxide pollution.     

多降液管筛板塔的设计计算

简要介绍多降液管筛板塔的特点及塔板参数的设计计算方法。     

Substrate-mediated interactions and intermolecular forces between molecules adsorbed on surfaces

Adsorbate interactions and reactions on metal surfaces have been investigated using scanning tunneling microscopy. The manners in which adsorbates perturb the surface electronic structure in their vicinity are discussed. The effects these perturbations have on other molecules are shown to be important in overlayer growth. Interactions of molecules with surface steps are addressed, and each molecule's electron affinity is shown to dictate its adsorption sites at step edges. Standing waves emanating from steps are demonstrated to effect transient molecular adsorption up to 40 A away from the step edge. Halobenzene derivatives are used to demonstrate how the surface is important in aligning reactive intermediates.     

聚合物多元醇产品质量的影响因素与控制

从内在和外在质量两个方面，简要论述了影响聚合物多元醇(POP)产品质量的因素和控制产品质量的措施。     

电石包装桶中乙炔气处理简述

电石在远距离运输过程中，受潮湿，生成乙炔气，遇明火燃烧或发生爆炸。对从业人员造成巨大危害。如何处理包装桶中的乙炔气成为电石产业的物流运输瓶颈。我公司在原来包二化比较实用的氮气置换基础上，逐渐形成了成熟的可使200KG大桶和100KG小桶中各种粒度电石包装桶中乙炔气浓度有效降低的出口电石质量控制体系。     

Studies on multilayer film coextrusion III. The rheology of blown film coextrusion

Multilayer blown film coextrusion was studied, both experimentally and theoretically. For the experimental study, an annular die with a feed-port system was designed and multilayer blown films were produced by rotating the inner mandrel with a one horsepower variable-speed drive at speeds from nearly 2 to 6 rpm, and by inflating the tubular molten film with air. The die has 16 feed slots and melt pressure transducers are mounted along the axial direction of the outer wall of the annular flow channel. The transducers were used to determine the pressure gradient in the annular flow channel, which then permitted determination of the reduction in pressure drop when different combinations of two polymer systems were coextruded. Polymers used for b own film coextrusion were: (1) low-density polyethylene with ethylene-vinyl acetate; (2) low-density polyethylene with high-density polyethylene; (3) low-density polyethylene with polypropylene; (4) high-density polyethylene with ethylene-vinyl acetate. For the theoretical study, stratified helical flow was analyzed using a power-law non-Newtonian model. A computational procedure was developed to predict the number of layers, layer thickness, and the volumetric flow rate as functions of certain processing variables (namely, the pressure drop in the die, and the angular speed of rotation of the inner mandrel of the die) and the rheological parameters of the individual polymers concerned. Comparison was made of the theoretical prediction of volumetric flow rate with experimental ones. Some representative results are presented of the theoretically predicted axial and angular velocity distributions, shear stress profiles, and shear rate profiles.     

混合电解质NaBr+NaAc十H_2O体系的活度系数的测定

用电势法测定了298.15K以及I为0.1、0.5、1.0、1.5、2.0、2.5和3.0 mol/kg时,NaBr在混合电解质溶液NaBr+NaAc+H_2O中的活度系数.实验结果用Harned、SRJ和Pitzer方程拟合,得到各种方程的相互作用参数,由拟合的标准偏差得知,Pitzer方程的拟合精度略好于前2个方程.用Pitzer混合参数θ_(Br-Ac)和ψ_(Br-Na-Ac)计算了NaAc在该混合体系中的活度系数和体系的过量Gibbs自由能.