Microstructural and textural characterization of a hot-rolled IF steel

The present paper reports the experimental results on the microstructural and textural characterization of a hot-rolled IF steel. The IF steel was hot-rolled in multiple passes in the austenitic field (1,070 °C) followed by air-cooling. SEM, TEM, and LOM were used to image the microstructure of the material. The global texture was determined by X-ray diffraction (XRD) technique. The mesotexture of selected regions was investigated by electron backscatter diffraction (EBSD). Results show the presence of a diffuse (nearly random) and weak texture in the hot-band that consists of recrystallized polygonal grains and subgrains. The fraction of boundaries with misorientations comprised in the interval 2° ≤ ψ < 15° was found to be lower than 5%. It can be concluded that these low angle boundaries and the presence of subgrains can be associated to the existence of a few areas softened by recovery during or after hot rolling in austenitic field.     

Optical and structural properties of MOVPE grown GaxIn1−xAs/InP strained multiple quantum well atructures

This paper presents a study of the structural and optical properties of strained GaInAs/ InP multiple quantum well (MQW) structures fabricated by LP-MOVPE. The composition of the Ga _x In_1−x As films ranged fromx = 0.17 tox = 1.0 and was determined by sputtered neutral mass spectrometry (SNMS) on thick layers. The structures of the MQW samples with well widths from 1.5 to 5 nm were investigated by high resolution x-ray diffraction (HR-XRD). Simulations of the diffraction patterns showed that transition layers of approximately 2 monolayer (ML) thickness with high lattice mismatch exist at the interfaces. Photoluminescence (PL) measurements indicate well widths of a multiple of a monolayer with local variations of one monolayer. The PL peak energies vary smoothly with the Ga concentration. These results were confirmed by optical absorption measurements.     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

Mesa and planar SiGe-HBTs on MBE-wafers

SiGe-HBTs have the potential for outstanding analog and digital or mixed-signal high frequency circuits widely based on standard Si technology. Here we review on MBE grown transistors and circuits. Processes and results of a research-like SiGe HBT and two possible production relevant HBT versions are presented. The high frequency results with f_max and f_T up to 120 GHz and a minimum noise figure of 0.9 dB at 10 GHz demonstrate the advantage of using MBE samples with steep and high base doping and high germanium contents. A comparison to the concept of reported low doped, low germanium and triangular profiled SiGe base layers, realized by UHV-CVD, is given. In addition, some circuit demonstrators of SiGe-ICs will be presented.     

Referenzprozesse für elektronische Ausschreibungen aus Sicht des industriellen Einkaufs

Many companies and purchasing departments only possess a limited knowledge about the modelling of inter-company business processes for electronic procurement. In the past the discussion about electronic procurement was mostly focused on technical aspects. This article introduces a reference process model for procurement auctions. The process model is made up of a basic process, which describes a minimal process for procurement auctions, and a number of process alternatives, which allow for the adoption of the basic process to changing parameters and individual company requirements.     

3 Jahre Akkreditierung Stand, Erfahrungen, Probleme

Vor 3 Jahren ist ein beispielloser Prozess zur Umgestaltung des deutschen Hochschulwesens angelaufen. Mit dem Übergang zu Bachelor- und Masterstudiengängen wurde eine Qualitätssicherung nach Art der international üblichen Akkreditierung erforderlich.     

Formula creatinine clearance as a substitute for 24-hour creatine clearance in children with kidney transplantation

A 10-year-old German shepherd dog presented with a periodontal 10 mm interproximal defect between the left mandibular fourth premolar and first molar teeth. Bone graft removed from the caudoventral portion of the ipsilateral hemimandible was placed in the defect as a component of the periodontal treatment plan. The use of bone graft likely contributed to periodontal pocket reduction.     

Image analysis of comet assay measurements

In the last decade the 'comet assay' or 'single cell gel electrophoresis assay' has been established as a sensitive method for the detection of DNA damage and the measurement of its recovery. The results published in the literature have often been obtained with different methods for comet structure measurement. In most cases these data are not comparable with each other. Even when using similar systems for the analysis, it is difficult to obtain matching data. This presentation will describe some technical aspects of our measurement equipment and evaluation software. It focuses on necessary experimental conditions to minimize errors in obtaining such data. The software developed here allows the rapid analysis of the microscopic samples (< 2 s per image). The image analysis was designed with respect to the morphological shapes of comet cells, which were investigated with a confocal laser microscope. The system is built with standard components which are commercially available. As a measure of the amount of DNA damage the ratio of fluorescence intensity was used inside the comet tail and the fluorescence intensity of the comet head. Other parameters such as DNA content, comet area, head radius, tail length and tail moment are also determined. The reproducibility of the system has been evaluated in several experiments over a period of 5 years.     

T cells of the human intestinal lamina propria are high producers of interleukin-10

BACKGROUND: The transmission of hepatitis A virus (HAV) has been associated with the use of a number of solvent/detergent-treated factor VIII concentrates and possibly a factor IX concentrate. These reports have emphasized the necessity of using virus-inactivation methods for plasma products that are capable of inactivating nonenveloped viruses such as HAV. STUDY DESIGN AND METHODS: A simple, highly accurate titration procedure for HAV, which allows extensive kinetic investigations of virus-inactivation procedures, has been developed. This system has now been used to evaluate the efficacy of vapor heating in inactivating HAV after the addition of the virus to a range of human plasma products. RESULTS: It was demonstrated that HAV was significantly more thermostable than other picornaviruses, which reinforced the fact that such viruses cannot be used as model viruses for HAV-inactivation studies. A one-step vapor-heating procedure was demonstrated to inactivate between 5.9 and > 6.3 log10 of HAV in different products. A two-step vapor-heating procedure had the capacity to inactivate between > 8.7 and > 10.4 log10 of HAV. Both procedures were more effective in inactivating HAV than was the pasteurization procedure used for virus inactivation in human albumin solutions. CONCLUSION: These data demonstrate the efficacy of vapor heating in inactivating high-titer HAV after the spiking of plasma products with virus. This study confirms and explains the results of controlled clinical trials and long-term clinical usage with respect to the lack of HAV transmission by such vapor-heated products.